Hurst 400 HP Boiler

Hurst Boiler System 1. 1- Used1995 200HP 150 PSI Hurst Hybrid Vessel 2. 1- Used 1995n refractory lined boiler furnace 3. 1- 8” underfeed stoker system 4. 1- 10” Fuel feed metering conveyor system 5. 1- Overfire air combustion fan with ductwork 6. 1- Underfire air combustion fan with ductwork 7. 1- Multi cyclone flyash collector 8. 1- Induced draft fan with exhaust stack 9. Muti cyclone and ID fan support steel with legs 10. Access platforms to boiler with ladders 11. Hurst open vented feedwater tank with 2 Grundfos feedwater pumps and control panel 12. Blowdown separator 13. Hurst Boiler control panel 14. Boiler piping parts 15. Boiler electrical parts 16.Equipment loaded onto trucks Optional: Fuel handling and storage supply system: Walking floor Vibrating Screen Screw conveyor Controls

Three systems available. Pricing will include removal and loading onto trucks. - Hurst Hybrid 600 HP 150 PSI - Hurst Hybrid 200 HP 150 PSI - Hurst Hybrid 300 HP 150 PSI Each system should include (email for specifics): Hurst Hybrid Vessel Hurst Boild Furnace with cast grates Hurst underfeed stoker system Hurt Metering conveyor system Overfire air combustion fan Underfire air combustion fan Hurst combustion air preheater Access platforms with ladders Boiler system control panel (PLC, frequency drives, UDC, control for automatic operation)

Used 1995 Hurst Hybrid Boiler system 200 HP 150 PSI 1– Hurst Hybrid Boiler 200 HP 150 PSI Boiler 1 - Hurst Boiler 200 HP Woodfired Furnace for Boiler vessel with cast iron grate system. 1 – Deaerator Tank 1 – Blowdown Separator for fuel storage equipment 1 – 8” Underfeed stoker System 1 – 10” Metering Bin Screw Conveyor with Hopper 1- 20HP Over fire air combustion fan 1- 15HP Under fire air combustion fan 1- Hurst multi-cyclone collectors 1- Induced draft fan

600 hp 300 psi Hurst Hybrid boiler system. 1996 year model Equipment Included: 1- 1- Hurst 1996 Hybrid Boiler 2- 1- Hurst woodfire furnace box 3- 1- Hurst 12” metering conveyor system 4- 1- Overfire air combustion fan 5- 1- Underfire air combustion fan 6- 1- Hurst combustion air preheater 7- 2- Hurst multi-cyclone collectors with rotary air lock 8- 1- Flyash Duct 9- 1- Induced draft fan with exhaust stack 10- Access platforms with ladders 11- Boiler and collector system support frame and legs 12- Boiler system control panel (PLC Controller, frequency drives, UDC) 13- Under feed fuel stoker system with cast iron grate system. 14- 20,000 lbs/hr DA Tank with two 15 HP Grunfos Pumps 15- Rear Injection Fan

Hutto Shaving Mill 9' Box (2) Heads 50 HP Motors Outfeed conveyor

Hutto Shaving Mill Hydraulic cylinder to hold dow scrap material Infeed shoot: 16" x 30" 30 HP Motor

12" blade 7-1/2 HP motor 3 phase Foot Pedal control Left Hand machine

Complete operation for sale. Land may also be available. (3) Jackson 8-knife shaving mills Newman 32-knife shaving mill Knife Grinders Shaker Screen Cut Off Saw Briquette System Drum Dryer with Burner and Blower Complete electrical and control (2) Verville VP300 Baggers with bins Shrink wrapper Truck Scales

175 KW -175 KVA 264 amps at 460v John Deere diesel powered 460v - 208v - 115v outlets housed in a container with ample access doors

14@ x 16” inlet 16” Round inlet no motor

(2) McConnell 40-50 MM BTU Gas Burners available

MEC 10x40 Single Pass Drum Trunions Controls

MEC 12'x42' Triple Pass Drum Trunions Cyclone available

This system was used at an old particle board facility. Seller thinks it is a MEC system. System starts with propane and then runs on dust. Includes burner, blower and piping.

225 KVA 480 volt to 208Y/120

Montgomery 100 HP Hammer Mill Includes: Outfeed conveyor and Infeed Hopper

In good condition. Has 50” opening. No drive motor but would take 100-200HP depending on material being run. No screen included. Very heavy weighs approximately 4 ton.

Very clean Newman G-200 Knife grinder. In good working order, grinds 17" on the inside and 20" on the outside.

Nice Newman G-280 tub grinder. Everything functional just needs cleaned.