Woodworking Equipment For Sale

Cemco 2000 Sander, Heavy Duty, 36inch wide, 20 hp, 3 phase, good condition $10,000 - Call 218-638-2810 or 218-410-0548

2000 MEREEN JOHNSON 424-DC DIP CHAIN GANG RIPSAW. 75HP ARBOR. COMPLETE BRAND NEW FEED CHAIN, NEW RUBBER INSERT, NEW CHAIN WAYS, NEW KICKBACK FINGERS, NEW OUTBOARD BEARING ON ARBOR AND NEW GEAR MOTOR ON PRESS ROLL HEIGHT ADJUST. SERIAL #MJ-6134. 10469 HOURS. 1 SAW SLEEVE INCLUDED. 460 VOLT. Price Reduced! $70,000.

The Northtech heavy-duty 40 HP glue-line capable multi-rip (“gang-rip”) saw with 12? maximum blade diameter quickly and accurately rips material up to 3-15/16” thick and 12” wide. Cutting both sides of your blanks at once provides incredible parallelism, reducing required moulder allowance, and increasing your yield. Short stock hold-down shoes allow for the cutting of small or thick materials. Variable feed speeds of 30 – 125 FPM and powered height adjustment improve operator efficiency. The innovative closed-link feed chain eliminates dangerous pinch-points to increase worker safety. Features: Close link chain vs. traditional open (pinch point) Auto lube system oiler has twice the number of lube points (critical) Can cut up to 3-15/16? with MRS-12 12? blade. Bottom kickback fingers for added safety Glue line rip capable Speed of saw blade 3550 RPM Variable feed speed 30’ – 125’ per minute Include (1) carbide blades: 12? x 36T x 70mm x 3.5mm kerf Net Weight: 3,300 lbs. Packing Weight: 3,525 lbs. Dimensions: 72”L x 62”W x 64”H Specifications: Main Motor Hp. = 40 hp. Voltage/ Freq. = 230460 Volt 60Hz Phase = 3 Phase Amp Requirement = 100/50 Amps Feed Hp. = 2 Hp. Feed System = 12” Dip Chain Drive System = Variable Speed Pulley Feed Speed = 30 – 125 FPM Variable Speed = Mechanical Wheel Adjustment Elevation Hp. = 1/4 Hp. Elevation Style = Push Button Elevation Sys. = Jack Screw / Linear Guides Total Hp. = 50 Hp. Electronics = CE Approved Components Dual Voltage = 230/460 Volt Control Voltage = 110 Volt Assisted Start = Wye-Delta Pass-Line = 29-1/2” Min. Length = 7” Butt Feed 12” Single Min. Width = 1/2” Max. Width = 12” Min. Thickness = 1/4” Max. Thickness = 3-15/16” Arbor Rpm = 3550 Rpm Blade Size = 12” Tungsten Carbide Tipped No. of Teeth = 36 Tooth Tooth Spacing = 1-3/16” Blade Kerf = 3.5 mm Cleaning System = Brush on Chain Vertical Travel = 1/4” – 4-3/16” Dust Collection = (2) 6” @ 1962 CFM Arbor Diameter = 70 mm Hold Down Style = (6) Rollers Throat Plate

Progressive multiblade gang saw, 75/60HP, vin #4VF 365TSTFS8001BVF2, we can load. Price Reduced! $24,500 931-205-8475

Selling a complete Planermill Line -Infeed, tilthoist, landing table, pineapple feed and transfer. -Stetson Ross 6-10-A1 Planer/Moulder c/w assortment of changeable 12 knife side heads can dress up to 6” thick, 8 knife top/bottom heads, 12” wide. Moulder heads with plenty of attachments. -Outfeed Belt, Slowdown Belt, accumulation transfer, lug loader, board turner, Canadian Trimmer with an assortment of trim length stops, trim block belts, green chain and stacking carts. Great planermill, ran 120,000fbm per shift when in production. 600V, 3phase, 60Hz system. Call/text for more details

Used Torit 376RF10 Reverse Air Bag House, 4,892 SQ/FT Cloth Media, 39,000 CFM Capacity @ 8:1 Air/Cloth Ratio, 12” Rotary Valve, Structural Support, Good Condition, $65,000

Wadkin 5 head, feed through molder, 9 x 4 inch max. With several cutting heads. Manifold and blower included. Very good condition $30,000 - Call 218-638-2810 or 218-410-0548

Whitney S-205 Planer 30", 3PH, great operating condition from brother's estate, phase converter available. Price Reduced! $18,500 OBO. 301-501-6344

15" color "Touch Screen" with Industrial Computer for setup and running CNC control of machine setup in less than one minute All components sized to handle 6x30 dowels Three v-groove heads with minimum 4" center to center Three banks of nine spindles for drawer front drilling One additional nine spindle bank to handle four sided drawers Two nine spindle horizontal banks for dowel drilling Runs up to 22 parts/minute in production Application Ability to v-groove drawer parts from 25" to 96" in length Ability to run parts as short as 10" without v-groove Ability to handle parts from 2-1/2" to 13-3/4" in width Ability to handle material thicknesses of 7/16" & 1/2" Makes box drawers with dowel construction Makes box drawers with 3 miters & 1 butt joint CNC Setup of machine Hopper loading of parts Parts feed through to the rear of the machine Like New Machine has run less than 100 parts. NEW PRICE: $235,000

15" color "Touch Screen" with Industrial Computer for setup and running CNC control of machine setup in less than one minute All components sized to handle 6x30 dowels Three v-groove heads with minimum 4" center to center Three banks of nine spindles for drawer front drilling One additional nine spindle bank to handle four sided drawers Two nine spindle horizontal banks for dowel drilling Runs up to 22 parts/minute in production Application Ability to v-groove drawer parts from 25" to 96" in length Ability to run parts as short as 10" without v-groove Ability to handle parts from 2-1/2" to 13-3/4" in width Ability to handle material thicknesses of 7/16" & 1/2" Makes box drawers with dowel construction Makes box drawers with 3 miters & 1 butt joint CNC Setup of machine Hopper loading of parts Parts feed through to the rear of the machine Like New Machine has run less than 100 parts. NEW PRICE: $235,000

Accu-Systems MMTJ Door Machine

Adwood Rapid EP8 Dust Collector

AEM 137-1 WIDE BELT SANDER1-Head, 36" width cap. - Combination sanding head with 4" dia. rubberized contact roll & 1-1/2" wide "dual action" polishing platen.Equipped with: -- Abrasive belt size 37" x 60" -- Pneumatic abrasive belt tensioning. -- POSI-TRACK electronic abrasive belt tracking. -- 20 HP main drive motor. -- 2 HP Variable feed speed motor for 15 - 45 FPM. -- Infeed & outfeed rubber covered holddown rolls. -- 0" - 6" manual thickness adjustment. -- 24" Infeed conveyor extensions with over thick protection device at infeed,Complete with: -- Air-operated disc brakes on sanding head, emergency stop button

AEM - 502-43-KPS, ...43" Planer Sander -- 1st Head: Helical planer; 25 HP, 208 - 230 - 460V. 3-Phase. -- 2nd Platen Head: 5"; 20 HP, 208 - 230 - 460 V; 3-phase; capacity 43 x 8 inches. -- Variable speed frequency drive. -- Load meters; pneumatic tracking. -- Power open & close.Also included: -- Extra feed belt. -- Original manuals and other documents.

AEM 8 Narrow Belt Sander

AEM 36" Sander

AES SIRIUS 950M ATC CNC MACHINING CENTER (FEED THRU): -- Specifications:Automatic CNC feed through Point to Point Boring Machine that combines flexibility and high productivity.A perfectly suited solution for small to midsize companies & artisans in need of an automatic solution for precision drilling with a low cost investment.Parts can be discharged at the opposite end of the machine for automated material handling or returned to the Operator for manual unloading. -- Working Capacity:Max. panel size on X-Axis is unlimited; Y-axis is 37.4" (950 mm); Z-axis is 2-3/4" (70 mm).Min. panel on size X-axis is 9.84" (250 mm); Y-axis is 3.14" (80 mm); Z-axis is 0.31" (8 mm). -- Positioning Speed: Panel feeding speed of 229 FPM (70 MPM); Y-axis at 229 FPM (70 MPM); Z-axis at 65 FPM (20 MPM).Axes positioning by AC drives & brushless Servo motors; the Panel moves in X-axis & the boring head moves in Y & Z-axes. -- Work Area:NC Controlled "Optical Material Sensor" creates a zero-panel reference point by reading the panel ends; this ensures that RH & LH (mirror image) panels will always be symmetrical.High precision clamping automatically positions the workpiece. Automatic presser moves independently and adjusts to workpiece thickness. Pneumatic side pusher make locating workpiece accurate and efficient. LH Side pressure clamp with automatic adjustment & pneumatic locking according to the panel width.Scratch resistant air floatation tables make for ease of loading and unloading from either side of the machine. -- Boring Unit:HSD Drilling head; 3 HP (2.2 kW), variable speed from 4,500 - 8,000 RPM motor. (10) Independent vertical spindles on 32 mm centers; (5) spindles in X-axis & (5) spindles in Y-axis.(6) Horizontal spindles with (2 + 2) in X-axis & (1 + 1) in Y-axis.(1) X-Axis grooving saw for max. 120 mm dia. blade; variable speed from 5,500 - 10,000 RPM. -- Machining:HSD 7 HP (5.5 kW) spindle; variable speed from 1,000 - 18,000 RPM with manual tool change system.(1) 6-Position ATC Automatic Tool Change system with ATC rotary magazine. -- Operator & Machine Control: PC Based user-friendly, icon-driven control housed on the main machine base; displays programming graphics, functions, and machine data. -- Complete with: Users & Maintenance Manuals; ALPHACAM "Essential" is provided with machine for ease of programming at the Controller. -- Software Disclaimer:EX-FACTORY INC. offers NO warranty or support, written or implied concerning any/all "optional" or "additional" manufacturer or 3rd party software supplied with this machine. All software related issues including re-licensing fees/requirements/functionality & training is ultimately the sole responsibility of the "Buyer".Actual Model is: AES SIRIUS 950M - ATC

ALDO BERRONE AIRONE 2 Single End Tenoner3-Station Tenoner with Trim; top & bottom tenons and cope head with manual sliding table. -- 1st Station: Trim saw, 10" max. dia. saw blade. -- 2nd Station: Top & bottom tenon heads, 25 mm dia. x 3-15/16" long spindles, 3/16" - 2-1/16" max. tenon thickness, 3 HP motor belt driven to saw & tenon heads. -- 3rd Station: Cope head, 35 mm dia. x 3-15/16" long spindle, 9-7/8" - 11-7/8" max. cutting circle, 2 HP motor. Equipped with: --² 15" Long x 12" wide sliding table (approx. 50" travel), tilts 0ø - 30ø down, -- Overhead pneumatic holddown and tilting fence line;

The VICTORY machine is a “heavy duty” linear sanding machine, that can be supplied with sanding drums or sanding disc’s depending on the application in the different industries. The machine comes standard with motorized adjustment, but can also be supplied with 14” PLC control with memory, so different programs can be stored & the setup can easily be done. The top/bottom drums comes in diameter of 400mm (16”) & side-heads comes in 300mm (12”) diameter, which will ensure better abrasive life. When machine is supplied with disc’s, each disc is 300mm (12”) in diameter. LS-TS- Offset Heavy duty motorsEasy changing of abrasivesHeavy duty constructionExtra large sanding wheelsTiltable side-heads Thickness of work piece: Min 0mm - max 150mm (6”)Conveyor Roller width: 300mm ( 12” )Conveyor motor: 0,75 kwSpeed of conveyor belt: 3– 15 m/min. ( 9-45 f/min)

Alpha Brush KS-LS Sander