Mereen Johnson 424 Gang Rip Saw

Mereen-Johnson Model 441-DC Gang Rip Saw Capacity: Arbor space 41” Arbor Drive: 75 HP 3600 RPM TEFC motor Feed Drive: HP TEFC variable speed direct; 45’ to 225’ feet per minute Hold Downs & Bed Plate: Four 5” dia. Air loaded high yield idle press rolls Saw Sleeve: One 41” capacity sleeve Dust Collection: Four upper dust pick-ups: two (2) 8” dia., two(2) 4” dia., one lower 4”dia. Pick-up:(requires total 4820 CFM @ 5,000 feet per minute) Swing Arm & Tip-Up Cart: One floor mounted dual shaft swing arm and one tip-up saw sleeve set-up cart Electrical: Arranged for 3 phase, 60 cycle, 460V Cameron Automated Opti-Rip Model #34F-M1 System: Manufacture Year: (2004) Complete with length measurement Tally System 5 infeed belt and chains for feeding a Gang Rip saw up to 41” wide 16 width sensors 3 sets of pinch rolls for short stock 1 fixed & 4 movable laser lights This system feed for 4’ to 16’ max lumber length It feeds from operator right to left Wired 220V; If 440V required, a transformer will be needed

Mereen Johnson 424 DC/SR4 Gang Rip Saw with Automated Infeed with multiple lasers manufacturer’s specs to be confirmed 24” width capacity 3-1/2” thickness capacity 75 HP main motor 3 hp feed motor feed rete 30-245 fpm

Mereen Johnson 424 DC Gang Rip Outfeed Rollers

These two rip saws were removed from service in working condition some time ago. The seller purchased them and never installed them. They have been in storage the whole time.

Mereen Johnson Model 312 Rip Saw Includes: New pads for the chain Includes: Twistlock Collar Mounted Saw Blades Available approx May 1, 2024

Mereen Johnson Model 312 DC SR1R Rip Saw 600 V/3 PH/60 Cy

Mereen Johnson 424DC 24" Wide Arbor 75 HP Motor (460v/3Ph) 3 HP Feed Speed Variable Feed Speed Air loaded pressure rollers

225 KVA 480 volt to 208Y/120

Miner 4” Edger

Montgomery 100 HP Hammer Mill Includes: Outfeed conveyor and Infeed Hopper

Main fan motor 20 HP RAL opening 14” Electrical panel Auto shaker filter cleaning Inlet pipe size 14” Number of filters 63

New Venture Manufacturing Gang Rip Saw Hydraulic Tank (5) Moving Blades Laser Tower Touchscreen Controls This machine has been removed from service. The photos showing the system setup were taken before it was removed

Newman End Trimmer K 20 MAXIMUM CUT LENGTH: 20' (6.1 m) 20' (6.1m) MINIMUM CUT LENGTH: 6' (1829 mm) 4' (1219 mm) 6' (1829 mm) MAXIMUM CUT THICKNESS: 7? (178 mm) 7-1/2? (190 mm) ACCURACY: +/- 1/32? (0.8 mm) +/- 1/32? (0.8 mm) FEED SPEEDS: 20 to 60 FPM (6.1 to 18.3 m/min.) FEED CHAINS: #60 roller chain #60 H type mill chain FEED DRAGS: 6 at 22? (559 mm) intervals 6 at 22? (559 mm) intervals SAW BLADES: 22? (559 mm) carbide, 60 teeth 1-1/2? (38.1 mm) bore, 10 gauge (3.4mm) 2 FLOOR SPACE: 20'-8? (6.3 m) x 6' (1.8 m) 20'-8? (6.3 m) x 6' (1.8 m) WEIGHT: Approximately 3500 lbs. (1590 kg) Approximately 3500 lbs. (1590 kg) 1`fixed saw and 4 movable saws 7.5HP each new electrical starters 1.5HP variable speed drive

Seller bought this saw with the intention of rebuilding it. He has most of the parts and started the work, but needs the space in the shop immediately. The first few photos are of the machine as it sits now (stripped). The next few show the machine BEFORE they started working on it. Newman KM16 Trim Saw Unscrambler Misc parts - shown in photos - everything going with the saw

Newman K20 Trim Saw (2) Blades - Aprox 20" diameter Infeed & Outfeed decks

Has (2) Blades Will cut up to a 12 x 12" Powered by (2) 20 HP 460 Volt 3 Phase motors Runs (2) 1 1/4" band blades Excellent Condition, (new condition with less than 4 hours use).

Northtech MRS-12N Gang Rip 50 HP Motor Needs a new safety with on the door

Northtech Chop Saw

- Close link chain vs. open (no dust or pinch point) - Oiler has twice the number of lube points (critical) - The VS adjustment location on the 14N. - Can cut up to 4 15/16? with 14? blade vs. the MRS-12 12? blade 3-15/16”. - Can run 12? as well on the MRS-14N - Bottom kickback fingers for added safety - Saws, with proper tooling and material, can glue line Specifications: - Main Motor Hp. = 50 Hp. - Voltage/ Freq. = 460 Volt 60Hz - Phase = 3 Phase - Amp Requirement = 35 Amps - Feed Hp. = 2 Speed 1.5 / 3 Hp. - Feed System = Feed Chain - Feed Speed = 25 – 120 FPM - Variable Speed = Variable Speed Pulley - Elevation Hp. = 1/4 Hp. - Elevation Style = Manual Wheel Adjustment - Elevation Sys. = Jack Screw / Linear Guides - Total Hp. = 53.25 Hp. - Electronics = CE Approved Components - Dual Voltage = Elevation Arbor Motors - Control Voltage = 110 Volt - Assisted Start = Wye-Delta - Pass-Line = 33-1/2” - Min. Length = 17-3/4” - Min. Width = 1/2” - Max. Width = 27-1/8” - Min. Thickness = 5/16” - Max. Thickness = 4-15/16” - Arbor Rpm = 3570 Rpm - Blade Size = 12” Tungsten Carbide Tipped - No. of Teeth = 36 Tooth - Blade Kerf = 3.5 mm - Cleaning System = Brush on Chain - Vertical Travel = 3/8” – 5” - Dust Collection = (2) 6” @ 1962 CFM - Arbor Diameter = 70 mm - Hold Down Style = Pressure Plate - Kickback Finger = (2) Top (1) Bottom Sets - Emergency Stop = Push Button - Rear E Stop = Push Button - Safety Feature = Safety Interlock Switch - Guarding = Full Cabinet Enclosure - Oiler = Automatic Mechanical Oiler - Low Oil Warning = Low Oil Shut-off - Fence Type = Adjustable - Fence Dims. = 103” Length - Frame Const. = 5/16” Steel Construction - Worktable Dims. = 27-1/8” x 64” - Infeed Table = 13-3/4” x 103” - Decible Rating = 74 dB - Net Weight = 4402 Lbs. - Gross Weight = 4694 Lbs. - Machine Dims. = 67” x 58” x 71” - Packaging Dims = 72” x 65” x 77”