MFA 6 3 heads Pad (inverter controlled) Pad (inverter controlled) brush CSD System 480 V 100 A

LSM 8 2 head wide belt sander · 1st Head: Segmented cross-belt, 5/8" wide segments (86 total) with "CSD" control, abrasive belt size 5.9" x 244", (5,400 mm X 150 mm ) inside chevron belt 5.9" x 191", sanding belt speed 5-12 m/s with 17 HP motor. (Inverter controlled) · 2nd Head: Combination head, with segmented polishing platen, 5/8" wide segments with CSD control, 17 HP motor, 106" x 53" ( 2,620 mm X 1,350 mm ) abrasive belt size. (Inverter controlled) Cleaning brush Vacuum bed

HEESEMANN LSM-8 C/L Wide Belt Sander, (2) Heads 53" (1,300 mm) Width cap., (1) Segmented cross-belt & (1) longitudinal combination head with segmented platen. Head Configuration: · 1st Head: Segmented cross-belt, 5/8" wide segments (86 total) with "CSD" control, abrasive belt size 5.9" x 244", (5,400 mm X 150 mm ) inside chevron belt 5.9" x 191", sanding belt speed 5-12 m/s with 17 HP motor. (Inverter controlled) · 2nd Head: Combination head, with segmented polishing platen, 5/8" wide segments with CSD control, 17 HP motor, 106" x 53" ( 2,620 mm X 1,350 mm ) abrasive belt size. (Inverter controlled) Equipped with & Features: · HESSEMANN's patented "CSD" magnetic pressure adjustment system, sensors spaced every 5/8" (16 mm) sense part configuration; (2) mm part thickness variation can be sanded without sand through’s, pressure for each segment can be pre-programmed to provide less pressure on the outer edges or more in the center if required. · The "CSD" computer control will hold approx. (20) programs or part configurations. · Additional features: Outfeed rotary panel cleaning brush with single end adjustment, 2 HP motor, air blast abrasive belt cleaners on all heads. · Variable feed speed from 13 to 82 FPM via Stober drive, 6.5 HP feed drive, motorized thickness opening 1/4" to 3-5/32" maximum. · Belt condition at 80% good.

Heeseman LSM8 Wide Belt Sander

Heian CNC Router This was used at a particle board plant that has been shut down for approx 10 years.

Confirming it is a Heil system. Seller is not sure. Actual dimensions: 42' x 10'6" Triple Pass Drum

Heil 15x32 Triple Pass Drum Dryer 8-10 TPH Drying Capacity Webb Burner Complete Dust Collection All Electrical & Controls 200 HP Wood Hog

Heil 10.5' x 32' Triple Pass Drum Dryer 1. Jackson Harvester Burner 24 million BTU 2. Fuel Bin 3. Pipe and fan from fuel bin to burner 4. Air lock on dryer 5. 8 X 24 3 pass dryer 6. Trunnions 7. Fans to dryer 8. Pipe to cyclone 9. Cyclone 10. Pipe to fuel bin 11. Fan moving sawdust to fuel bin 12 Hog with 200 HP motor 13 Dust collection system

12'x42' Triple Pass Drum 20 MM BTU Webb Burner Burner feed bin Burner blowers Blower to pull shavings through drum Cyclone BMM 3-level Shaker Screen (2) Outfeed Conveyors Electrical controls

This is a Horizontal Band Saw Resaw Machine with Two saw heads. This is an ideal Machine for the recovery line, as it processes the slabs coming out of the Vertical Twin band saw machine “the resaw process”. It comes with an input chain conveyor, driven press rollers. Cutting Height and saw blade tensioning setting system. It also comes with main motor, motor drive panel, the Frequency inverter, gear motor drive panel. It does not include the saw blade. - Wheel blade: Ø1000mm; - Wheel blade width: 5"; - Maximum wood width: 400 mm; - Maximum wood height: 380 mm; - Minimum length of wood: 1250 mm; - Single Input table/ conveyor width: 600 mm; - Motor press roller: 1 cv 4P (2x); - With two independent infeed rollers; - Forward speed: 45-50m / min for small logs; - Main motor indicated: 2 x 60 hp - Soft starter Drive panel: included; - Servo motor thickness setting system (INCLUDED); - Main transmission belt: 3 x Channel B; Length: 6.532mm; - Width: 2.220mm; - Weight: 7655kg.

Vance PT600R8 Drum Chipper See this machine at IWF Atlanta 2024! This Wood Drum chipper PT600 is used in production of wood chips from logs and veneer waste. It has a toothed roller system that allows efficient material infeed, a rubberized conveyor belt and a Hydropneumatic unit to lift the rotor cover for maintenance. It comes with 01 chipper Knife set and 01 nose bar set. It does not come with the output conveyor. - Width of inlet: 600 mm; - Height: 300 mm; - Rotor diameter: 800 mm; - Toothed roller: 01 upper and 01 lower; - Grooved rollers: 01; - Rollers gear motor: GD (helical gears); - Metal detector: Flat model; - Rollers motor size: 5 hp (2x); - Number of rotor knives: 02; - Wood chip size: 25 - 40 mm; - Main motor 125 hp 4P: Included; - Drive panel: Included; - Lead Time: 240 Days; - Estimated production: 55 m3 / h (it may vary according to the type of material and time used with blade sharpening); - Infeed conveyor length: 3 500 mm (included); - Width: 1 850 mm; - Height: 1 .150 mm; - Overall length: 6 700 mm; - Approximate weight: 4,900 kg.

This Grinder was recently taken out of service and was running good. No electrical controls. Ready to load.

This Grinder was recently just taken out of service. It ran very good before taken out. Does not include electrical controls.

Vecoplan RG 42/60 XL 60 HP Motor 15" Rotor 42" x 52" Hopper Opening 1" Screen This machine went through a rebuild. It was not big enough for the buyers application. Available immediately.

Vecoplan Model 45/12/2VU HZF Grinder 75 HP Motor 18" Wide opening No Vibrating Infeed conveyor

Vecoplan RG52-60 U Stretch Slow Speed Grinder 60 HP Motor No Control Panel

Brand new never used!! 16’8” long 22” wide 19” height (adjustable)

Vermeer HG365 Grinder New infeed roll and remote control Ready to go to work!

VIET Planer Sander Sander model S2 321 HR/KRT ( 2018 ) !st head planer with helical insert cutter knives 30 HP 460 volts 2nd head drum contact roller 3rd head combination drum rollers with finish platen Both sanding heads run by 30 HP motor 460 volts Adjustable rubber coated pressure rollers Opening capacity range 1/8” to 6” Sanding belt size 44” x 103” Feed speed 19 to 52 FPM Electronic digital readout with auto thickness positioning Disc brakes on each machining station Front and rear emergency push buttons Electro pneumatic sanding belt tracking This machine has low hours as owner only ran half days first year and less after next years

Visionary Trim Saw