Cemco 2000 Wide Belt Fair/good condition. It starts and runs until we unplugged it 12 years ago Belt size 37 x 75 2004 Single head 1- 5” roller top, 2 - 5” rollers bottom, 1 rubber covered, 1 steel. No platen Thickness ¼” – 6” 2179 hours on machine 230 V, 60 CY, 3 PH Variable speed feed 20 HP motor Emergency Brake

(14) spindles with 1-1/2 hp motors on each. On/off switch for each motor. chucks adjust to grip up to 1/2” bit stroke adjustable from 4” to 10” 121” x 39-1/2” table with (4) hold downs Adjustable speed hydraulic feed 230 volt 3 phase

Nice CF Nielson BP5500 Press. The plant shut down in 2014. The machine was run again for a test in 2016 and everything was in good working condition. They have the dies and pistons to make round and octogonal logs. - Briquetting press CF Nielsen BP5500 - Dies to make 3’’ round logs and 2½’’ octogonal logs - Lignin dosing system - Water pump to add water if material too dry - Home-made automatic speed adjustment with encoder. - Briquette breaker from CF Nielsen at the end of the cooling line - Home-made flying saw with lenght asjustment at the end of the cooling line too with capability to switch from the saw to the breaker. - Can run up to 1200kg (even 1400kg I think) per hour depending on material and briquette shape - Cooling line can be opened to make pucks also. - 575V AC motors - Installed in 2008 - 10,865 hours

CFORM Edger/Rip Saw - model CKM160 This machine was purchased new and installed the beginning of 2023. It has less than 20 hours. The seller changed applications. Machine is ready to load. Photos coming! Manufacturer information: Double Edgeing & Slicing Cutter the value of lumber with clean edges can often exceed the value of rough-cut boards. In one pass, this Twin Blade Board Edger takes boards fresh off the mill and turns them into clean, square edged lumber. This edger is easy to use, with one fixed blade and one moveable blade that adjusts with a manual dial. Easily select the precise size of lumber you need. Lower the perimeter fence when you need to edge only one side of a board. Features: Movable finger iron platers for safe guidance and protection. Maximum 15 raws circular saws, adjustable distances. Hydraulic upper roller pressure and movable cyclinders. Maximum cutting height (inch)6 5/16?, 4 11/16?

This grinder was removed from service in good working condition. It is ready to load/currently in storage 200 HP Main Motor Cutters 117 F-Cutters Screen (4 ) 22" Diameter Wide with 1-1/2" Holes The width is 51” and the height is 17” (infeed opening)

Challenger Grinder as pictured

Champion 5 HP 575 Volt 2 Stage 24 CFM unit.

Automatic template Maker for grinding your own Molder knives

Automatic template Maker for grinding your own Molder knives

15 HP 6500 CFM 10” WC

Clark Lift 9' Mast Unsure of model number. Plate is worn down. Machine starts and runs.

Clark 6000 lb 60” forks side shift Hard tire

Cleaver Brooks 200 HP Boiler

Cleaver Brooks Boiler 500 HP 4-Pass dryback Natural Gas 60 PSI Design pressure

12,000 MBTU Natural Gas or Propane Fired New never used (2) Available

Cleereman Carriage PawTawJohn setworks and 3D scanner Three headblock model LPC-42 Four position dogs in/out and bottom dog turning Spare cylinders for all positions Spare top and bottom dogs 30 hp hydraulics

Cleereman Log Turner

Cleereman #36 Circular Sawmill 100 HP Electric Engine Left Hand

Complete, state of the art, drying systems that are custom manufactured for your application, location and production. Systems are designed to be fueled by green wood waste. Sized from 75-600 cubic yards per hour. Contact CMS for more information. - ?Furnace systems complete with fuel bin, dampers & controls - Material infeed & outlet airlocks - Complete ductwork systems - Air recycling systems - All controls & instumentation - Complete system integration

This machine is in good working condition and can be inspected under power. Specs (to be confirmed): - Electric spindle 18.1 HP - X-axis stroke 145.66î - Y-axis stroke 82.67î - Z-axis strke 13î - Working area 145.66î x 68.90î - Automatic tilting head - Telescoping spindle extension for surface polishing - (26) ISO 40 tool holders at rear - Bar code reader for program interface