Table Configuration: • KOMO VR 512 Mach I CNC Router • 60 x 144" Cast aluminum machined vacuum table • Table has been designed for High Flow vacuum pump • Ideal for nested based manufacturing • Heavy Duty fixed Gantry Bridge • A-Frame style Gantry Support legs • Pop up part locating pins (set of three pins) Head Configuration: • 12 HP High Frequency 4-pole Router Spindle • Programmable spindle speeds from 9,000 - 18,000 RPM • 8-Position Dynamic tool changer with BT-30 tool holders • (6) Vertical drill spindles on 32 mm centers • (4) Horizontal boring spindles with 1 + 1opposing in the X-axis and 1 + 1opposing in the Y-axis Positioning: • All axes are positioned by AC Servo Drives • Heavy Duty Profiled machine rails and bearing trucks • Preloaded precision ball screws for positioning • Automatic Lubrication system to all bearings • Rapid travel speeds of 1,250 IPM on both the X and Y-axes • Travel speeds of 600 IPM on the Z-axis Controller: • FANUC 210i PC Front end Controller • Windows Operating system • RS-232 Serial interface • 3-axis simultaneous control • Feed rate override • Spindle speed override • Hand help pendant • Remote operating pedestal with vacuum and cycle start buttons, pop up pins, as well as emergency stop.

Komo VR508 CNC Router 60" x 120" Table 25 HP Sullair Vacuum Pump Dust Collector (10 or 15 HP - need to confirm) (2) Two main router heads with Quick Change (2) Vertical Drill Units (1) 8 HP 10" Saw Fanuc Control

Krusi Krusimatic G2 Log Milling Machine - Capable of milling dovetails, lap joints, joinery, end cuts, key cuts and drill holes - Fully automated - Still installed and available for inspection

Kuka KR60-3 Robot System KR C4 Control System Kuka Programming Smart Pad Robot Enclosure (3) Heave duty conveyor racks

Max. operating width in grain direction approx. 3200 mm Min. operating width in grain direction approx. 600 mm Width of the veneer strips across the grain from approx. 60 mm Veneer thickness approx. 0.3 – 2.5 mm Capacity up to 28 joints/min. Feed speed approx. 30 m/min. Operating voltage 480 V, 3 Ph, 60 cycles

Nailmate pallet nailer

Chop Saw with Infeed Unscrambler Swing cut off with a 12" blade 5 HP Motor

Dimensions are 19'4"x14'7"x18'2" Gas fired with Maxxon

2021 heavy duty 7.5 HP Used Dust Collector 220 V / 3 Ph / 60 Hz Dust Collector has an efficiency of 85%

HMC Corporation Sawmill Has a 36 inch diameter blade

HMC Corporation Sawmill Has a 36 inch diameter blade

Strapping Cart with Tools

Pallet racking 9'6 ft & 8’4 racks X 42” wide and 16’ tall 31 - 4 shelf racks or can expand to 62 shelf racks (2 shelves)

Chip Conveyor Approx 400' Removed from closed mill with low hours. Some new conveyor included.

Kiln Carts as pictured Wheels 72” on center Qty 153 47” x 108” x 10” Qty 125 47-3/4” x 152” x 12” Qty 18 48” x 152” x 16” Qty 1 62” x 108” x 10-1/2”

Electric Good running condition Manual feed table Max 52" cutting width Length 23'4"

Electric Good running condition Manual feed table Max 52" cutting width Length 23'4"

Spray booths - (3) Available Approx 15'x12'

Roll Case Conveyor

Chain Conveyor Lumber Deck