AEM 401-43 WIDE BELT SANDER1-Head, 43" width cap., combination sanding head with a 6" dia. rubber covered contact roll and 1-1/2" wide finishing platen.Specifications: -- 20 HP Main drive motor; 1.5 HP variable feed speed motor for 5 - 50 FPM. -- Abrasive belt size 43" x 60", with air tensioning and POSI-TRACK electronic abrasive belt tracking. -- Double infeed & double outfeed rubber covered holddown rolls, -- 0" - 8" Manual part thickness opening with mechanical digital readout, (4) screw jacks for conveyor bed opening.Complete with: -- Infeed conveyor extension with safety stop bar and motor load meter. -- Heavy Duty endless conveyor belt. -- Quick release outboard support. -- Air operated disc brakes on main motor of positive stopping of sanding head in (4 - 7) Seconds. -- Emergency stop functions at pinch points. --Centralized control panel. -- Comes with: Extra Sanding Drum that can be recovered Replaced with new drum and bearings about 5 years ago. Comes with a quite a few sanding belts.

BIESSE - ARTECH LEVIA 330, ...3-Head Wide Belt Sander43" Width cap. Drum, Drum, and Combination Head.Head Configuration: -- 1st Head: Rubber covered Contact Roll, 6" dia., 25 HP motor. -- 2nd Head: Steel Contact Roll, 6" dia., 25 HP motor. -- 3rd Head: Combination head with a rubber-covered Contact Roll and Finishing Platen.NOTE: There are (2) 25 HP motors; one drives the 1st head and the 2nd drives the other (2) heads.Specifications: -- 44" x 85" Abrasive belts, electronic abrasive belt tracking; all contact rolls with pneumatic seclusion; Head #3 with air belt cleaner. -- EASY PRO "2000 C" Processor with (200) programs, touchscreen for control of Sander functions, thickness opening, feed speed, sequential startup, contact roll seclusion, and abrasive belt cleaner. -- Conveyor belt feed, 11 - 66 FPM variable feed speed, 2 HP feed drive with inverter control. -- 1/8" - 7-7/8" Motorized thickness adjustment with LED readout; automatic part thickness setup.Equipped with & Features; -- Automatic conveyor belt tracking. -- Infeed & outfeed shoes or rubber-covered holddown rolls, infeed panel "over thickness" sensor. -- Electronic brakes on both sanding head motors. -- Infeed emergency stop, 3-roll infeed extension, and motor load meter.

BOARKE 43 RK Wide Belt Sander, (2) Heads43" Width cap. Drum, Combination HeadHead Configuration1st Head: Contact Roll for Calibration 10"; Dia. Contact Roll, 85 Shore Hardness Dynamically balanced, 25 HP, 230/460 V, wired 230 V2nd Head: Combination Unit for Finish Sanding with ContactRoll, Pad or Both 5.5 “dia. Contact Roll 55 Shore Hardness, Dynamically balanced, 2.8"; wide Finishing Pad, 20 HP, 230 / 460 V, wired 230 V.Specifications: -- Sanding Units include: Photo electric belt tracking, Large diameter Tension, and Idle Rolls, Rigid Main beams for superior accuracy, 2.8"; Dia. spring loaded hold down rolls Quick release Tie Down Blocks, Y Delta Motor Starters -- Feed System: 4 ea. 5 ton capacity lifting screws, Heavy Duty 3-Ply conveyor belt, Heavy slider bed, machined for accuracy -- Variable conveyor speed from 7 – 45 FPM, Inverter Controlled Variable Speed, 2 HP drive motor, Conveyor belt centering device -- Infeed Roller, Guide Ways provide accurate vertical movement -- Control Panel (Located on Belt Loading Side for convenience) -- Digital Controller positions machine thickness -- Digital Readout in Inches or MM, And ν Buttons micro-adjust thickness in 0.001"; increments, Micro-Adjustment hand wheel for final thickness in 0.001"; increments -- Automatic Thickness Set Up, Motorized Thickness adjustment -- Amp Meter, and Volt MeterEquipped with & Features: -- Over Thickness Shut Off, Body activated safety switch at front of machine -- Door activated safety switches on ALL Doors, Emergency Stops front and rear -- UL / CE approved electrical components -- Disc Brakes on both motors -- Emergency Shut off activated when Air Pressure is too low, Overloads are tripped -- Emergency Stops are activated

BOERE - TKS 900, ...2-Head Top Wide Belt Sanding Machine900 mm (36") Working width; equipped with: (1) Contact roller, (1) Fine sanding pad. Head Configuration -- 1st Head: Rubber contact roller, spirally grooved, Shore hardness 80, diameter 265 mm (10.4"), driven by 18 kW (25 HP) motor. -- 2nd Head: Sanding pad, electronic-pneumatic controlled, 114.7 kW (20 HP); Air blowing unit for cleaning the abrasive belt. -- All heads use abrasive belts size: 910 x 1,900 mm (35.8" x 74.8").Feed System -- Variable feed speed: From 5 - 25 MPM (16 - 82 FPM); 1.5 kW (2 HP) motor. -- Motorized part thickness opening: 3 - 150 mm (0.1" - 6"), driven by 0.12 kW (0,15 HP) motor.Complete with: -- Emergency Stop Systems for abrasive belt breakage and low belt tension. -- Infeed safety bar for operator protection and oversized parts. -- Automatic Star Delta starters, motor load meters. -- Pneumatic belt tension. -- Emergency Stops at the front & back. -- Extended infeed belt, approx. 42" long.Actual model: BOERE "TKS 900".

BOERE - TPK-900, ...Planer Sander w/(2) Heads -- 2-Head, 900 mm (36") width cap.; equipped with: (1) Knife planer head and (1) Rubberized Drum. -- 1st Head. Helical knife planer head with: (4) Spirals of 4-sided carbide inserts, each 14 mm x 14 mm; 20 HP motor. -- 2nd Head. Drum approx. 10" dia. rubber covered contact roll; 15 HP motor; all heads with air-operated caliper type disc brakes. -- Variable feed speed: 13 - 52 FPM; 2-1/2 HP motor; automatic conveyor belt tracking; anti-kickback fingers on infeed; infeed holddown shoes' double outfeed pinch rolls on outfeed. -- Motorized part thickness adjustment: 0" - 6"; LED readout display. Complete with: -- Controls mounted on belt loading side; load meters for each head;, conveyor infeed extension.

BUTFERING E-LINE 213RL (2) Head Wide Belt Sander53" Width cap. Drum, Combinbation HeadHead Configuration1st Head : Steel calibrating contact roll 200mm Dia. 20 HP2nd Head : Combination Head 20 HP. ( Comes with (2) slide in platens, one for veneer, one for solid wood ) Rubber contact roll 140mm Dia. Specifications -- 53" x 75" Abrasive belts, -- Electronic abrasive belt tracking -- Conveyor belt feed with 2-speed motor, 18/ms, 2.3 HP motor, infeed & outfeed spring loaded holddown rolls, -- 1/8" - 5-3/4" motorized part thickness adjustment with LED readout.Equipped With & Features -- Infeed panel "over-thickness" sensor -- Brakes on both sanding head motors, -- Infeed emergency stop, -- Roller infeed conveyor extension -- motor load meters.

--MAKE OFFER!--EXCELLENT CONDITION!-- BÜTFERING SWT134/RRC 1100 mm (43.31") 3-Head Wide Belt Sander, with Combination Head Specifications: Suitable for sanding of veneered parts in 1 or 2 passes with segmented pad only & Thickness tolerance compensation up to 1 mm (0.04”), Suitable for sanding of solid wood & wood based materials in single pass with 3 grit sequence. Thickness cap. 3 mm - 160 mm (0.19” - 6.30"). Variable feed speeds 2.5 - 13 MPM (8.5 - 42 FPM). Equipped with: 1st Head: 160 mm (6.30”) Dia. Grooved steel contact roll, with Grit size compensation, Automatic positioning for calibrating, & 15 kW (20 HP) - 2,930 RPM Motor with Electric braking. 2nd Head: 160 mm (6.30”) Dia. 85° Shore Grooved rubber-covered contact roll, with Grit size compensation, Automatic positioning for calibrating, & 15 kW (20 HP) - 2,930 RPM Motor with Electric braking. 3rd Head: Combination head, with 60 mm (6.30”) Dia. 65° Shore Grooved rubber-covered contact roll, 3-3/4" Dia. Smooth steel contact roll, 3-1/8” W Electronically-controlled segmented pad finishing platen with 35 mm (1.38”) W Segments, & 18 kW (15 HP) Motor with Electric braking. 1-7/8” Dia. Rubber-covered roller & spring-loaded segmented nylon rollers on infeed & 1-7/8” Dia. Rubber-covered spring-loaded hold-down rollers between heads & after 3rd head. 1,120 mm x 1,900 mm (44.09" x 74.80") Abrasive belts, with Electronic oscillation. 43-1/4” W x 5’ L Feed belt, with 1.3 kW (1-3/4 HP) Feed motor with Frequency inverter, 44” W x 8” L 2-Roll Infeed Extension, & Automatic conveyor belt tracking. Power raising of conveyor bed, with Automatic thickness adjustment & Over thickness Protection. LCD Touchscreen control, with 5-1/2” Display, & Motor load meters. Complete with: Original Production Instructions. CURRENCY NOTE: Negotiable Price is listed in U.S. Dollars.

BÜTFERING SGO 211 RK Wide Belt Sander, 2-Head,(43") Working width, equipped with (1) Contact Roller and (1) Combination Head consisting of Contact Roller & Finishing Platen.Head Configuration;1st Head: Rubber contact roller 160 mm (6.3") with 15 kW (20 HP) motor.2nd Head: Combination head with rubber covered contact roller and finishing platen, not segmented, 11 kW (15 HP) motor.Specifications -- Both heads use 1,120 x 1,900 mm (43" x 75") abrasive belts with electronic abrasive belt tracking. -- Feed system: Conveyor belt feed with variable feed speed 2,6 - 13 m/min (8,5 - 42 FPM), 1,1 kW (1.5 HP) feed drive, auto belt tracking. Part thickness 3 - 160 mm (0.1 - 6.3"). Automatic motorized part thickness adjustment with 0,1 mm LED readout.Equipped with and Features -- Electronic emergency brakes on sanding head motors. -- Infeed emergency stop. -- Motor load meters for supervision of stock removal. -- Roller table extension at infeed. -- Emergency stops at in & outfeed end—automatic star/delta starters.

BÜTFERING SWT134/RRC 1100 mm (43.31") 3-Head Wide Belt Sander, with Combination HeadSpecifications: -- Suitable for sanding of veneered parts in 1 or 2 passes with segmented pad only & Thickness tolerance compensation up to 1 mm (0.04";), Suitable for sanding of solid wood & wood based materials in single pass with 3 grit sequence. -- Thickness cap. 3 mm - 160 mm (0.19"; - 6.30"). -- Variable feed speeds 2.5 - 13 MPM (8.5 - 42 FPM).Equipped with: -- 1st Head: 160 mm (6.30";) Dia. Grooved steel contact roll, with Grit size compensation, Automatic positioning for calibrating, & 15 kW (20 HP) - 2,930 RPM Motor with Electric braking. -- 2nd Head: 160 mm (6.30";) Dia. 85° Shore Grooved rubber-covered contact roll, with Grit size compensation, Automatic positioning for calibrating, & 15 kW (20 HP) - 2,930 RPM Motor with Electric braking. -- 3rd Head: Combination head, with 60 mm (6.30";) Dia. 65° Shore Grooved rubber-covered contact roll, 3-3/4" Dia. Smooth steel contact roll, 3-1/8"; W Electronically-controlled segmented pad finishing platen with 35 mm (1.38";) W Segments, & 18 kW (15 HP) Motor with Electric braking. -- 1-7/8"; Dia. Rubber-covered roller & spring-loaded segmented nylon rollers on infeed & 1-7/8"; Dia. Rubber-covered spring-loaded hold-down rollers between heads & after 3rd head. -- 1,120 mm x 1,900 mm (44.09" x 74.80") Abrasive belts, with Electronic oscillation. -- 43-1/4"; W x 5’ L Feed belt, with 1.3 kW (1-3/4 HP) Feed motor with Frequency inverter, 44"; W x 8"; L 2-Roll Infeed Extension, & Automatic conveyor belt tracking. -- Power raising of conveyor bed, with Automatic thickness adjustment & Over thickness Protection. -- LCD Touchscreen control, with 5-1/2"; Display, & Motor load meters.Complete with: -- Original Production Instructions.

Homag Sander Butfering W300 SWT345/QCUH (4) Heads wide belt sander53" Width cap. Cross belt , Combi head Electronic platen, Universal oscillating brushing cups, Chevron super-finish head Electronic platen, Cleaning brushHead Configuration1st Head: processing unit Cross belt Electronic platen2nd Head: Processing unit Combi head Electronic platen3rd Head: Processing unit Universal oscillating brushing cups (includes additional brass wire 300mm drum and 300mm Tynex Drum in carts never used4th Head: Processing unit Chevron super-finish head Electronic platen5th Station Head cleaning brushSpecifications -- Air jet blowers -- Integrated vacuum -- Bed width 53"; -- Includes AC unit -- Digital calliper -- About 30 belts different grit sizes -- All heads are program controlled5’ out feed table with interoll rubber rollersEquipped with & Features -- Custom metal fencing -- 6 custom metal belt racks -- Voltage 460 -- Machine commissioned June 2021 -- Sellerwill include preparing the machine for shipping and loading NOTE Reason for sale. Changes in manufacturing process.

Bütfering SWT 124 RC Wide Belt Sander (2) Heads43" Width cap. Drum, Combination HeadBütfering SWT 124 RL Features: --Touch Screen display and control. -- Capacity of (125) programs. -- Conveyor speed is controlled within the program. -- Controls the number of sanding heads activated. -- Controls use of sanding pad or contact roller on combination heads. -- Controls thickness of work piece. -- Controls air jet belt cleaning on or off ( only on models with this feature). -- Error message display including safety functions. -- Displays in mm or decimal inches. -- Hour meter display. -- Conveyor table mounted on four heavy duty jack screws. -- Automatic conveyor belt tracking. -- Electronic belt oscillation system. -- Electronic motor braking system. -- Over thickness protection system. -- Safety interlocks on all access doors. -- In feed roller table. -- Emergency stops at in feed and out-feed locations.Head Configuration:1st Head: Contact roller head located in position #1 includes:160 mm diameter steel profile contact roller. -- Automatic height positioning -- Grit compensation -- 20 HP motor -- Cutting speed is 60 FPS.2nd Head: Combination head located in position #2 includes: -- 65 shore profiled rubber contact drum --Automatic height positioning -- Air cushion sanding pad with rise and fall timing -- 18 HP motor -- Cutting speed is 60 FPSSpecifications: -- Working width 1,100 mm (43";) -- Abrasive Belt width 1120 mm (44";) -- Abrasive Belt length 1,900 mm (75";) -- Work piece thickness min. 3 mm ( 1/8"; ) -- Work piece thickness max. 160 mm (6-3/8";) -- Variable conveyor speed 8 - 42 FPM; Feed motor 1 HP -- Contact Roller - Head #1 20 HP, 60 FPS belt speed. -- Combination- Head #2 18 HP, 60 FPS belt speed.Utilities: -- Total power required 28 kW. -- Dust collection requirements 1500 CFM; -- Dust outlet – head #1 160 mm ( 6.25 "; ) -- Dust outlet – head #2 160 mm ( 6.25 "; ). -- Compressed air requirements 90 PSI; Air consumption per cycle 4 CFM; Machine net weight 3960 Lbs.

CAM-WOOD WS-DA2560 Wide Belt Sander, (2) HeadsWith the two-head 25" width capacity wide belt sander, you can accurately, and heavily sand your stock with the first drum head and with the second combination head you can give an unlimited fine finish. -- Rugged heavy-duty sheet metal construction designed for durability usage -- Powerful industrial motors drive sanding and auto infeed smoothly. -- Infeed and outfeed are spring-loaded hold-down rollers to ensure positive feeding without sanding marks. -- Combination platen & drum sanding head for best sanding choice such as: -- With the platen up, the sander functions as a drum-only machine, for sanding with a 40 ~ 100 grit belt. -- With the platen and drum same level, intermediate and final finishing is possible, using a grit of 120 ~ 180. -- With the platen down (below the drum), used for the fine finishing or lacquer sealer sanding, with 180 ~ 600 grit.Head Configuration1st Head : 15 HP Drum2nd Head : 10 HP Combination HeadSpecifications: -- Max. Working Width 25" Max. -- Working Thickness 5" -- Min Working Length 12½" -- Sanding Belt Dimensions (W x L) 25" x 60" -- Dust Collection Hood (Dia x Holes) 5" x 2 -- Main Motor 15, 10 HP; -- Feed Motor 2 HP -- Table Raising / Lowering Motor ½ HP -- Var. Feed Speed (FPM) 20 ~ 80 20 -- Working Air Pressure 6 CFM -- Exhaust Volume Require 1800 CFM -- N.W. 4400 Lbs - G.W. 5000 LbsEquipped with and Features -- Sanding platen with a quick release and lock down design for easy removal or loading of graphite platen. -- Computerized thickness adjustment control with accurate digital readout; key in the size desired and automatic table movement for sanding thickness within 0.005"; accuracy. -- Large-size diameter contact drum is dynamically balanced, rubber-covered spiral grooves designed to provide considerable advantages for the effective removal of material. -- Special rubber feed belt for safe non-slipping, transporting the workpieces. -- The abrasive belts are tracked by oscillating cylinders linked to the upper roller. The edge of the belt is detected by an electric eye sensor, which in turn controls the air supply to the position via solenoid value. Also, one limit switch is located on each end of the top roller of the sandpaper for quick stop in case of belt breakage. -- The main table is designed with a convenient leveling adjustment which ensures greater stability with excellent tolerance providing a variable range from 0"; ~ 5"; sanding thickness. -- (4) Heavy-duty jack screws power conveyor table elevation.

CAM-WOOD WS-DA3760 Wide Belt Sander, (2) HeadsWith the two-head wide belt sander, you can accurately, and heavily sand your stock with the first drum head, and with the second combination head, you can give an unlimited fine finish.Application: -- Rugged heavy-duty sheet metal construction designed for durability usage. -- Powerful industrial motors drive sanding and auto infeed smoothly. -- Infeed and outfeed have spring-loaded hold-down rollers to ensure positive feeding without sanding marks. -- Combination platen & drum sanding head for best sanding choice such as: --With the platen up, the sander functions as a drum-only machine, for sanding with a 40 ~ 100 grit belt. -- With the platen and drum same level, intermediate and final finishing is possible, using a grit of 120 ~ 180. -- With the platen down (below the drum), used for the fine finishing or lacquer sealer sanding, with 180 ~ 600 grit.Head Configuration:1st Head : 20 HP Drum2nd Head : 15 HP Combination HeadSpecifications: -- Max. Working Width 37" Max. -- Working Thickness 5". -- Min Working Length 12½". -- Sanding Belt Dimensions (W x L) 37" x 60". -- Dust Collection Hood (Dia x Holes) 6" x 2. -- Main Motors 20 and 15 HP. -- Conveyor bed Feed Motor 2 HP. --Table Raising / Lowering Motor 1/2 HP -- Variable Feed Speed 20 - 80 FPM. -- Working Air Pressure 6 CFM. -- Exhaust Volume Require 2,400 CFM. -- N.W. weight 5,100 Lbs.Equipped with and Features: -- Sanding platen with a quick release and lock down design for easy removal or loading of graphite platen. -- Computerized thickness adjustment control with accurate digital readout; key in the size desired and automatic table movement for sanding thickness within 0.005"; accuracy -- Large size diameter contact drum is dynamically balanced, rubber-covered spiral grooves designed to provide considerable advantages for the effective removal of material. -- Special rubber feed belt for safe non-slipping, transporting the workpieces. -- The abrasive belts are tracked by oscillating cylinders linked to the upper roller. The edge of the belt is detected by an electric eye sensor, which in turn controls the air supply to the position via solenoid value. Also, one limit switch is located on each end of the top roller of the sandpaper for quick stop in case of belt breakage. -- The main table is designed with the convenient leveling adjustment which ensures greater stability with excellent tolerance providing a variable from 0"; ~ 5"; range sanding thickness. -- (4) Heavy-duty jackscrews power conveyor table elevation.

CAM-WOOD WS-DA4375X DUAL HEAD WIDE BELT SANDERWith the two-head wide belt sander, you can accurately, heavily sand your stock with the first drum head, and with the second combination head, you can give an unlimited fine finish.Application: -- Rugged heavy-duty sheet metal construction designed for durability usage. -- Powerful industrial motors drive sanding and auto infeed smoothly. -- Infeed and outfeed have spring-loaded hold-down rollers to ensure positive feeding without sanding marks. -- Combination platen & drum sanding head for best sanding choice such as: --With the platen up, the sander functions as a drum only machine, for sanding with a 40 ~ 100 grit belt. -- With the platen and drum same level, intermediate and final finishing is possible, using a grit of 120 ~ 180. -- With the platen down (below drum), used for the fine finishing or lacquer sealer sanding, with 180 ~ 600 grit.Head Configuration:1st Head : 30 HP Drum2nd Head : 20 HP Combination HeadSpecifications: -- Max. Working Width 43" Max. -- Max. Working Thickness 5". -- Min Working Length 12½". -- Sanding Belt Dimensions (W x L) 43" x 75". -- Dust Collection Hood (Dia x Holes) 6" x 2. -- Main Motors 30 and 20 HP. -- Conveyor bed Feed Motor 3 HP. --Table Raising / Lowering Motor 1/2 HP -- Variable Feed Speed 20 - 80 FPM. -- Working Air Pressure 6 CFM. -- Exhaust Volume Require 3,800 CFM. -- N.W. weight 6,160 Lbs.Equipped with and Features: -- Sanding platen with a quick release and lock down design for easy removal or loading of graphite platen. -- Computerized thickness adjustment control with accurate digital readout; key in the size desired and automatic table movement for sanding thickness within 0.005"; accuracy -- Large size diameter contact drum is dynamically balanced, rubber covered spiral grooves designed to provide considerable advantages for the effective removal of material. -- Special rubber feed belt for safe non-slipping, transporting the workpieces. -- The abrasive belts are tracked by oscillating cylinders linked to the upper roller. The edge of the belt is detected by an electric eye sensor, which in turn controls the air supply to the position via solenoid value. Also, one limit switch is located on each end of the top roller of the sandpaper for quick stop in case of belt breakage. -- Main table designed with the convenient leveling adjustment which ensures greater stability with excellent tolerance providing a variable from 0"; ~ 5"; range sanding thickness. -- (4) Heavy-duty jackscrews power conveyor table elevation.

CAM-WOOD A-3760X Combination Head Wide Belt SanderSpecifications: -- 36" Width cap. - Combination Sanding head with rubber-covered contact roll and adjustable finishing platen. 20 HP main drive motor. -- 37" X 60" Abrasive belts, pneumatic abrasive belt tensioning. -- 0" - 5" Feed through bed adjustment, Digital thickness set-up via 0.5 HP motor power elevation for thickness opening. -- Variable conveyor feed speed from 20 to 60 FPM, 2 HP feed motor. -- 5" Max. working thickness, 7" min. working length, -- Double Infeed & outfeed spring loaded holddown rolls.Complete with: -- Magnetic controls, 6" dia. dust collection hood, and safety shutoff. - 1,500 CFM Dust collection required.

CAM-WOOD A-2560 Single Head, Wide Belt Sander;Features & Specifications: -- 24" Width cap. - sanding head with a rubber covered contact roll and adjustable finishing platen, 10 HP motor. -- 25" x 60" Abrasive belts, pneumatic abrasive belt tensioning. -- 0" - 5" Feed through bed adjustment, 0.5 HP motor power elevation for thickness opening. -- Variable conveyor feed speed from 17 - 51 FPM, 1 HP feed motor. -- 5" Max. working thickness, 7" min. working length, -- Double Infeed & outfeed spring loaded holddown rolls.Complete with: -- Magnetic controls, 6" dia. dust collection hood, and safety shutoff. - 1,500 CFM Dust collection required. Optional: 10 HP Single Phase motor

CAM-WOOD A-3775 Single Head Wide Belt SanderSpecifications: -- 36" Width cap. - Combination Sanding head with rubber-covered contact roll and adjustable finishing platen. 20 HP main drive motor. -- 37" X 75" Abrasive belts, pneumatic abrasive belt tensioning. -- 0" - 5" Feed through bed adjustment, Digital thickness set-up via 0.5 HP motor power elevation for thickness opening. -- Variable conveyor feed speed from 20 to 60 FPM, 2 HP feed motor. -- 5" Max. working thickness, 7" min. working length, -- Double Infeed & outfeed spring loaded holddown rolls.Complete with: -- Magnetic controls, 6" dia. dust collection hood, and safety shutoff. - 1,500 CFM Dust collection required.

CAM-WOOD WS-NDA 1300 3-Head Planer Sander[Equipped with Planer, Drum and combi head]Features: -- This machine is especially designed for removing heavy material such as glued-up panels, bent boards, and rough lumber. -- The first station is a knife planer head, followed by a combi head with drum and platen at the second station and a finishing platen head at the third station. -- Head configuration can be made to meet customer’s requirements. -- The spiral planer cutter head is fitted with 14 x 14 MM, four-edge throwaway Tungsten Carbide knife inserts, providing a superior chip removal rate, minimum noise, and an extremely smooth cutting effect. -- Changing knife inserts is convenient without removing the cutter head. The spiral cutter head is precision machined from special aluminum alloy steel, tempered, and precision ground by a CNC machine center. -- Anti-kickback fingers, mounted at the infeed of the machine, this anti-kickback finger gives a safety guard for the operator. -- Insufficient pressure protection: If inadequate working air pressure occurs, the machine brakes automatically for safety guard. -- The irreversible running of the pressure roller runs in a single direction only, giving an additional safety guard for panel kickback. -- Automatic elevation of conveyor table (micro-computer controlled with digital readout): it accurately displays the position of the conveyor table. It automatically moves to the setting thickness for planning and sanding. -- Panel cleaning brush roller: built at the outfeed end of the machine, this cleaning brush roller cleans the powder on the sanded panel. -- Hold-down plate is hard chrome treated for maximum wear resistance.Specifications: -- First head Planer with 40 HP motor -- Second head combi drum & platen with 30 HP motor -- Third head finishing platen with 30 HP motor -- Panel cleaning brush at outfeed with 1/2 HP motor -- Working width: 52" -- Working thickness up to 6 1/4" -- Minimum working length: 21" -- Feed speed 10 FPM to 90FPM inverted driven by 5.5 HP motor -- Table hoist motor 1 HP -- Sanding belt size 52" X 75" -- Floor space requirement: 107" X 103" X 80", weight 12,300 Lbs

CAM-WOOD WS-M1000 NAX Planer Sander -- 2 Heads with 39.4" width capacity planer head and combination sanding headFeatures: -- This machine is especially designed for tale off heavy materials such as glue panel, bend board, rough lumber. -- The first head is a knife planer head, with 25 HP motor. The spiral planer cutterhead is fitted with 14 x 14 mm, four edge throw away Tungsten Carbide knife inserts, providing superior chip removal rate, minimum noise, and extremely smooth cutting effect. Changing knife inserts are conveniently done without removing the cutterhead. -- The second head is a combination of drum and platen driven by a 20 HP motor, belt size 40.5" x 78 3/4". (1030mm X 2000 mm) -- Anti-kickback fingers, mounted at the infeed of the machine, this anti-kickback finger gives a safety guard for the operator. -- Insufficient pressure protection, in case insufficient working air pressure occurs, the machine brakes automatically for safety guard.Irreversible running of pressure roller, runs a single direction only, giving an additional safety guard for panel kickback. -- Motorized elevation of conveyor table (micro-computer controlled with digital readout), it accurately displays the position of the conveyor table and automatically moves to the setting thickness for planning, sanding. -- Panel cleaning brush roller; built at outfeed end of the machine, this cleaning brush roller cleans the powder on the sanded panel. -- Hold-down plate is hard chrome treated for maximum wear resistance.Technical Specification: -- Working width 39.4" (1000 mm). -- Working thickness up to 6 1/4". -- Minimum working length 21". -- Feed speed 10 to 90 FPM inverted driven by 3 HP motor. -- Table raised and lowered by 1/2 HP motor. -- Cleaning brush driven by 1/2 HP

CAM-WOOD WS-MN700NAX Planer/Sander Equipped with: -- (2) Heads with 27" width capacity planer head and combination sanding head -- This machine is specially designed for take-off heavy materials such as glued-up panels, bend boards, and rough lumber. -- The first head is a knife planer head, with 20 HP motor. The spiral planer cutterhead is fitted with 14 x 14 MM, four edge throw away Tungsten Carbide knife inserts, providing superior chip removal rate, minimum noise, and extremely smooth cutting effect. Changing knife inserts are conveniently done without removing the cutterhead. -- The second head is a combination of drum and platen driven by a 20 HP motor, belt size 28 3/4" X 75" -- Anti-kickback fingers, mounted at the infeed of the machine, these anti-kickback fingers provide a safety guard for the operator.Features: -- Insufficient pressure protection, in case insufficient working air pressure occurs, the machine brakes automatically for safety guard.Irreversible running of pressure roller, runs a single direction only, giving an additional safety guard for panel kickback. -- Motorized elevation of conveyor table (micro-computer controlled with digital readout), it accurately displays the position of the conveyor table and automatically moves to the setting thickness for planning, sanding. -- Panel cleaning brush roller; built-in at the outfeed end of the machine, the cleaning brush roller cleans the fine sanding dust off the sanded panel. -- Hold-down plate is hard chrome treated for maximum wear resistance.Technical Specification: -- Working width 27" -- Working thickness up to 6 1/4" -- Minimum working length 20" -- Feed speed 20 to 90 FPM inverted driven by 3 HP motor -- Table raised and lowered by 1/2 HP motor -- Cleaning brush driven by 1/2 HP