//This machine is in an Auction on exfactoryauctions.com// //Link to machine: http://exf.ac/i6c WALKER 14" Bench-Top Vertical Band Saw Specifications: Table size 17” LR x 18" FB x 20” H. Maximum height under guard 8". Equipped with: 3/4 HP - 1,725 Motor. 16” Rubber-covered spoked wheel.

WEB MECAHNICAL JET 10M Jet Air Oven Supply Side complete with the following: -- 400,000 BTUH rating, 3,200 CFM forward curved blower, 5 HP motor 575 V /3 Ph /60 Cy. -- Inlet filter section HEPA 99% DOP rated, Magnehelic gauge across the filter section. -- Thermometer to show outlet temperature, Thermostat to set and control temperature design from 60° -70° C, -- Jets designed to control flow across the belts. Exhaust Side complete with the following: -- Vane axial fan set to exhaust 600 CFM,1/2 HP motor. -- Direct drive fan with motor out of air stream, external grease fittings for lubrication.Heating Module: -- Air makeup sized for 3,200 CFM, 2 HP motor, rated for 400,000 BTUH. --Fan to exhaust through 2"; pleated filter and 12"; HEPA filter, Down discharge,3 HP motor, 3,200 CFM @ 2.0"; E.S.P. -- Engineered for 90° F temperature rise, 0.4 MBTU/hr hydronic coil, features FUJI temperature selector. Conveyor: -- Robust 10-gage steel frame, Novo 40 grey belt designed for up to 90° C and with Auto tracking mechanism. -- Large size 6"; driver and idler pulleys, Support pulleys 3"; as required. -- Heavy duty NORD gear box and a 2 HP direct coupled motor. OPTIONAL (Not included in Price):IR Adder (Lamps): -- Three (3) MW IR lamps in the center of the oven, Three (3) MW IR lamps at the end of the oven, -- Heated length of lamps 54";, dual gold plated element, 3,200 watts per bulb. -- Lamps are designed to sit between the jets on the oven with lamps 8"; (200 mm) above belt and 8"; apart. - Please add ...$ 7,700Control Panel for the above (600 V - Electric) complete with: -- Line interlock, E-stop, fuses, disconnect switch, DC power supply. -- Phase angle controller to control two (2) banks of three (3) lamps. CSA approved panel. - Please add ...$ 12,100BOILER: -- One (1) RBI dominator boiler "DB 600" to supply up to 600,000 BTUH. - Please add ...$ 18,900

WEB MECHANICAL HYDRONIC OVEN - Low Velocity Flash Off - STAGE # 1 and High Velocity Bake Oven - STAGE # 2 STAGE # 1, Low Velocity Flash Off Oven. -- The oven consist of one (1) only hot water oven, 14' wide x 9' high x 30' long with Air flow requirement of 30 FPM/ 9,000 CFM.Supply side complete with the following: -- 400 000 BTUH heat exchanger -- Motor/blower, 2 HP 575 V / 3 Ph / 60 Hz -- Thermometer to show outlet temperature -- Thermostat to set and control temperature to design temperature -- RTD's (1) for accurate oven dispersion temperature -- Eighteen gage galvanized steel panels -- Perforated metal side walls for even air distribution -- Design temperature of 30 -40°C -- Adjustable inlet mixing damper with intake filter (70% recycle) -- Exhaust fan for combustible gasesExhaust will be complete with the following: -- Size 14 direct drive aluminum fan wheelset to exhaust 30% of the contaminated airflow (2,500 CFM) -- Direct drive with the motor out of air stream -- External grease fittings -- Fan module c/w aluminum extrusions and galvanized panels, and will be complete with HEPA style filter, -- DWDI fan, space for hot water heat exchanger STAGE 2 HIGH-VELOCITY OVEN BAKEThe oven consist of one (1) only hot water oven, 14' wide x 9' high x 20' long with Air flow requirement of 50 FPM/ 9,000 CFM Supply side will be complete with the following: -- 1,500,000 BTUH heat exchanger -- 10,000 CFM -- Motor/ blower 5 HP 575v / 3 Ph / 60 Hz -- Thermometer to show outlet temperature -- Thermostat to set and control temperature to design temperature -- Eighteen gage galvanized steel panels c/w 3" insulation -- Perforated metal side walls for even air distribution -- Design temperature of 40 - 60C 104 - 140 F -- Adjustable inlet mixing damper with intake filter (85% recycle) -- Exhaust fan for combustible gases Exhaust will be complete with the following: -- -- -- Size 12 direct drive aluminum fan wheelset to exhaust 15% of the contaminated airflow (1,500) CFM) -- Direct drive with motor out of air stream -- External grease fittings There will be two (2) air knives one at start of the oven and one art the exit to control heat and fume exhaust Air knives will be complete with Multivee filters for inlet air Fan module c/w aluminum extrusions and galvanized panels will be complete with HEPA style filters, DWDI fan, space for hot water heat exchanger.

--MAKE AN OFFER!---EXCELLENT CONDITION!-- WEEKE BHX 050 CNC MACHINING CENTER (VERTICAL), with 1,127 Main Usage Hrs. (As of 10/31/23): Specifications: Flexible "Vertical" Machining Center that uses less than 5 sq/m of valuable floor space, in addition to an innovative Panel Handling System. Working Cap.: Max. workable part size for "X" axis is 98.4" (2,500 mm); "Y" axis 33.4" (850 mm); max. part thickness 2.4" (60 mm). Min. worktable part size for "X" axis is 7.8" (200 mm); "Y" axis 2.7" (70 mm); min. part thickness of 0.47" (12 mm). - Automatic infeed & outfeed from the LH or RH side. Positioning Speed: The "BHX 050" can reach movement speeds of 164 FPM (50 MPM) in "X" & "Y" axes & 50 FPM (15 MPM) in "Z" axis with total safety, providing an unmatched working capacity. Boring Unit: (1) 3 HP (2.3 kW), Variable speed from 1,500 - 7,500 RPM motor, (8) independent vertical spindles with: (4) spindles in "X" axis & (4) spindles in "Y" axis. (3) Horizontal Spindles with (1+1) in "X axis & (1) spindle in "Y" axis. Boring block has QUICK-CHANGE spindle system. Operator & Machine Control: WEEKE "POWER CONTROL" + Windows + WoodWOP 6.0 + Operating System. 17" TFT Monitor; Real-time multitask processing; programs can be transferred via diskette or downloading by wire is possible. Complete with: Pneumatic part clamping devices; sound enclosure and complete set of safety devices. Options Include: ? (1) "X" Axis grooving saw; 9,000 RPM, saw blade dia. 100 mm. ? (1) 7 HP (5 kW) Electro-spindle router with hydraulic "QUICK-CHANGE" tool system & "ETP 25" tool holders; variable speed from 6,000 - 18,000 RPM; 2010 DATALOGIC “PowerScan M8500” Industrial Handheld Area Imager Bar Code Reader, with “STAR” Cordless System. Actual Model is WEEKE BHX 050. CURRENCY NOTE: Negotiable Price is listed in U.S. Dollars.

AAF PULSE-PAK 21-3H Pulse-Jet Cartridge Dust Collector. (3H) is three-high filter elements. (21) is the total number of Panel Pak V's.The Panel Pak filter element has two flat panels of pleated media in a Vee-Configuration allowing installation and change-out with minimum time and effort. Each cartridge has its own gasket ensuring a positive, air tight seal. -- Consists of two modules: one containing (9) 3x3 filters and the second contains (12) 4x3 filter cartridges, for a total of (21) cartridges. -- Housing dimensions: 191.75" High (with 48" hopper clearance), 104.25" Wide, 94.25" Depth, and Weighs about 6,400 Lbs. -- Air consumption about 6 cubic feet/hr. at 90 PSI of clean dried air. -- Fan and Airlock available at extra cost. please inquire.

ACCU-SYSTEMS H49 CNC BORE, GLUE & DOWEL INSERTER: -- Specifications: (2) Working zones and an overall 49" max. width capacity. --(1) CNC Controlled head assembly with rapid (side-to-side) traverse, assembly with boring, gluing & insertion unit, 1 HP - 18,000 RPM drill motor. -- (4) Vertical pneumatic hold-down clamps, function selector control for boring only or doweling, adjustable drilling speed. -- 1-9/16" (40 mm) Max. dowel length, setup for 8 mm dowel dia.; height adjustment up to 1-1/8" material thickness with digital readout. -- Operator Interface: CNC "Color Touch-Screen" Controller for function & part programming and program storage. -- Complete with:(1) 12" Dia. vibratory feed hopper. Totally sealed electronically metered glue system with 1-button flushing. -- 100 PSI high power glue pump, 2-1/2-gal. glue tank. Anti-slip table surface. 49" "X" axis cap. -- Rack & pinion drive, and centralized dust collection manifold.

This is for a pair of fully enclosed and drive through Semi Downdraft paint booths with On The Roof of the booth heated air make-up that are connected by a cross passage room/ paint room. There are actually (2) two booths that are assembled end to end making the overall length of Each tunnel 55' 9" long (see layout drawings) Also a Paint mixing room with presurization and heat is included connecting the two long booths. There is also a presurized and heated paint mixxing room (see specifications below) that comes with this equipment. See layout drawings in this listing attachments,The equipment has low usage and is currently set up. price does not include tear down but that can be quoted. Booth Description:Dual Skin Space Saver - 28’ l x 14’4"; w x 13’1"; h External DimensionsDrive ThruSide Service Door with Observation Window IncludedHorizontal Intake - DF 1.2 Mil BTU / 14,000 CFM / 10 HP / ADH 500 / UPGRADEExhaust Bridge - 30"; Tube Axial Fan / 5 H.P. Motor / 12,500 CFMSmart Pad Control Panel - (1) 10 HP / (1) 5 HP / Burner Voltage OutputSmart Pad Control PanelVFD for a 5 HP Single Motor 480 V Three PhaseVFD for a 10 HP Single Motor 480 V Three Phase480 / 277 V Three Phase with 120 V Single Phase Burner Circuit(10) Upper Gable and (4) Lower Vertical Lights - 4’28"; Duct Work Package - 15’ (Intake & Exhaust)LED Upgrade per FixturePass Between Room:AccuMix Dual Skin Mixing Room 8’ w x 16’ d - Attached Two Sided12"; Duct Work Package - 15’ (1 Exhaust)LED Upgrade per FixturePaint Mixing Room:AccuMix PRO Mixing Room 8’ w x 10’ d GalvanizedWhite on White Option for a Mixing RoomPRO Prep - 24’ l x 24’ w x 12’ h Above Ground Solid Back with (1) ExhaustPRO Stand Alone Unit - 1.2 Mil Btu Burner / 10 HP Motor / 14,000 CFMRear Wall Exhaust - 30"; Tube Axial Fan / 5 H.P. Motor / 14,000 CFM UpgradeSmart Pad Control PanelVFD for a 5 HP Single Motor 480 V Three PhaseVFD for a 7.5 HP Single Motor 480 V Three Phase480 / 277 V Three Phase with 120 V Single Phase Burner Circuit(4) Ceiling Mounted Lights Inside Access - 4’ Four Bulb28"; Duct Work Package - 15’ (Intake & Exhaust)Curtains - 12’ l x 9’ h SolidCurtains - 24’ l x 9’ h Solid9x24 wallLED Upgrade per FixtureLED Upgrade per Fixture12"; Duct Work Package - 15’ (1 Exhaust)

ACT 4-16 Cartridge Dust Collector Cartridge style downward flow dust collector rated at 8,000 CFM. Specifications: -- 20 HP Direct drive, top mounter blower rated at 8,000 CFM @ 10" w.c. -- (16) Nano Elite, flame-retardant, Nano-Fiber merv 15, cartridge filters with up to 4,064 sq. ft. of filter media that are 99.9% efficient. -- Pulse control timer board with built-in digital pressure gauge. -- Drum lid with latch kit, quick-lock easy-access filter doors. -- Magnetic motor starter.Equipped with: -- Automatic reverse jet cleaning via compressed air, (1) pulse valve per (2) cartridges for a total of (8) pulse valves. Goyen diaphragm and solenoid valves -- Heavy Duty steel legs position unit approximately 4' above the ground made with 7 and 10-gauge construction. Options: -- Fan outlet damper. -- Fan outlet silencer. Other models available, please check with the Product Manager10 year workmanship and materials warranty -- Made in the USA

ACT 3-6 Cartridge Dust Collector Cartridge style downward flow dust collector rated at 4,000 CFM. Specifications: -- Blower, 10 HP rated at 4,000 CFM @ 10" w.c. -- Holds (6) Nano Elite, merv 15, cartridge filters with up to 1,524 sq. ft. of filter media that are 99.9% efficient. -- Pulse control timer board with built-in digital pressure gauge. -- Drum lid with latch kit, quick-lock easy-access filter doors. -- Magnetic motor starter panel. -- (6) Filter Upgrade to ACT Nano-Elite, flame-retardant, Nano-Fiber media with industry best Merv 15 efficiencyEquipped with: -- Automatic reverse jet cleaning via compressed air, (1) pulse valve per (2) cartridges for a total of (3) pulse valves. Goyen solenoids and diaphragm. -- Heavy Duty steel legs position unit approximately 4' above the ground made with 7 and 10-gauge construction. -- 12" in-let. -- Silencer for TCBI 1010 year manufactures materials and craftsmanship warranty . Made in the USA

ACT 3-12 Cartridge Dust Collector Cartridge style downflow dust collector rated at 6,000 CFM. Heavy-duty with 7 and 10 gauge construction. Specifications: -- Blower, 15 HP rated at 6,000 CFM. -- (12) Nano Elite, MERV 15, cartridge filters with 3,046 sq. ft. of filter media that are 99.9% efficient. -- Reverse pulse filter cleaning system. -- Pulse control timer board with built-in digital pressure gauge. -- Drum lid with quick-lock easy-access filter doors. -- Magnetic motor starter and disconnect. -- 16" inletEquipped with: -- TCBI 15 HP Blower with direct drive, top mount. -- Automatic reverse jet cleaning via compressed air, (1) pulse valve per (2) cartridges for a total of (6) pulse valves. Goyen solenoids and diaphragm. -- Heavy Duty steel legs position unit approximately 4' above the ground made with 7 and 10-gauge construction. -- Drum Lid Latch Ring. -- Motor starter with disconnect. -- 10 year workmanship and materials warranty -- Made in the USA

ADVANCE LIFTS P-6036+M Scissor LiftThe P-Series lifts are Advance Lifts most popular series as they fit a wide array of manufacturing applications.SPECIAL FEATURES & BENEFITS: -- These units are equipped with the patented “Platform Centering Devices";, which doubles or triples lift life. -- All of the controllers are Underwriter Laboratory listed assemblies. -- These units are fully primed and finished with a baked enamel finish. -- The cylinders are machine grade with clear plastic return lines. -- All pressure hoses are double wire braid with JIC fittings. -- The reservoirs are mild steel. -- These units conform to all applicable ANSI codes.Specifications: -- 6,000 Lbs. capacity. -- Platform size 36" x 72" (Min. Platform Size: 24" x 48" Max. Platform Size: 48" x 72") -- Max. End Load Capacity 4,100 Lbs. -- Max. Side Load Capacity: 3,500 Lbs. -- Baseframe Size: 24"" x 48". -- Lowered Height: 6.5". -- Raised Height: 42.5". -- Approx. Speed Up: 27 sec. -- Internal Motor: 2 HPWarranty 10 Year Structural / 250,000 Cycles - 1 Yr Parts and Labor

AEM 401-43 WIDE BELT SANDER1-Head, 43" width cap., combination sanding head with a 6" dia. rubber covered contact roll and 1-1/2" wide finishing platen.Specifications: -- 20 HP Main drive motor; 1.5 HP variable feed speed motor for 5 - 50 FPM. -- Abrasive belt size 43" x 60", with air tensioning and POSI-TRACK electronic abrasive belt tracking. -- Double infeed & double outfeed rubber covered holddown rolls, -- 0" - 8" Manual part thickness opening with mechanical digital readout, (4) screw jacks for conveyor bed opening.Complete with: -- Infeed conveyor extension with safety stop bar and motor load meter. -- Heavy Duty endless conveyor belt. -- Quick release outboard support. -- Air operated disc brakes on main motor of positive stopping of sanding head in (4 - 7) Seconds. -- Emergency stop functions at pinch points. --Centralized control panel. -- Comes with: Extra Sanding Drum that can be recovered Replaced with new drum and bearings about 5 years ago. Comes with a quite a few sanding belts.

AES SIRIUS 950M ATC CNC MACHINING CENTER (FEED THRU): -- Specifications:Automatic CNC feed through Point to Point Boring Machine that combines flexibility and high productivity.A perfectly suited solution for small to midsize companies & artisans in need of an automatic solution for precision drilling with a low cost investment.Parts can be discharged at the opposite end of the machine for automated material handling or returned to the Operator for manual unloading. -- Working Capacity:Max. panel size on X-Axis is unlimited; Y-axis is 37.4" (950 mm); Z-axis is 2-3/4" (70 mm).Min. panel on size X-axis is 9.84" (250 mm); Y-axis is 3.14" (80 mm); Z-axis is 0.31" (8 mm). -- Positioning Speed: Panel feeding speed of 229 FPM (70 MPM); Y-axis at 229 FPM (70 MPM); Z-axis at 65 FPM (20 MPM).Axes positioning by AC drives & brushless Servo motors; the Panel moves in X-axis & the boring head moves in Y & Z-axes. -- Work Area:NC Controlled "Optical Material Sensor" creates a zero-panel reference point by reading the panel ends; this ensures that RH & LH (mirror image) panels will always be symmetrical.High precision clamping automatically positions the workpiece. Automatic presser moves independently and adjusts to workpiece thickness. Pneumatic side pusher make locating workpiece accurate and efficient. LH Side pressure clamp with automatic adjustment & pneumatic locking according to the panel width.Scratch resistant air floatation tables make for ease of loading and unloading from either side of the machine. -- Boring Unit:HSD Drilling head; 3 HP (2.2 kW), variable speed from 4,500 - 8,000 RPM motor. (10) Independent vertical spindles on 32 mm centers; (5) spindles in X-axis & (5) spindles in Y-axis.(6) Horizontal spindles with (2 + 2) in X-axis & (1 + 1) in Y-axis.(1) X-Axis grooving saw for max. 120 mm dia. blade; variable speed from 5,500 - 10,000 RPM. -- Machining:HSD 7 HP (5.5 kW) spindle; variable speed from 1,000 - 18,000 RPM with manual tool change system.(1) 6-Position ATC Automatic Tool Change system with ATC rotary magazine. -- Operator & Machine Control: PC Based user-friendly, icon-driven control housed on the main machine base; displays programming graphics, functions, and machine data. -- Complete with: Users & Maintenance Manuals; ALPHACAM "Essential" is provided with machine for ease of programming at the Controller. -- Software Disclaimer:EX-FACTORY INC. offers NO warranty or support, written or implied concerning any/all "optional" or "additional" manufacturer or 3rd party software supplied with this machine. All software related issues including re-licensing fees/requirements/functionality & training is ultimately the sole responsibility of the "Buyer".Actual Model is: AES SIRIUS 950M - ATC

AGET 20SN5157 Cyclone with FT-40 Baghouse2,300 CFM at 9.3" SP; 5 HP Top-mounted blower motor cyclone, 8" inlet dia.,10" outlet diameter. -- Dust particles are pulled through the cyclone with larger particles dropping through the cyclone to dump into collection bin. Finer particles are forced through the Baghouse to filter the remaining air.. -- Includes; 5 HP LEESON ELECTRIC TEFC top-mounted blower, cyclone, AGET "FT-40" Baghouse after-filter, manual slide gate opening and automatic bag shaker which comes on after shut down of collector. -- Interior bag house with (40) 5" dia. x 8' L cloth tubes, total filter area of 383 sq. ft. The larger dust particles are pulled through cyclone into (2) 55-Gal barrel storage with manual slide gate opening at bottom.

AIR CURE 484RF10 Dust Collection System with Rotary Air Lock and Abort Gate.Specifications: -- Filter area capacity 56,000 CFM @ 9:1 Air to Cloth Ratio (ACR), approx. 13'- 2" dia. round baghouse; -- (484) Cloth filter bags of 10' length (3" x 6") oval bags provide for radial movement of bag during cleaning for longer life), 6,180 sq. ft. of filter area. -- Designed for filtration media cleaning via 7.5 HP approx.on board rotary air pump for compressed air operating at about 7.5 PSI. Return air outlet and approx. 48" x 48" inlet for dust laden air. -- Rotating cleaning air manifold driven by 1 HP motor, (1) NEMA IV timer & solenoid/diaphragm valve control pulse jets of air to clean each row of bags; galvanized steel bag frames with positive bag bolt down to eliminate leakage and ride up of bags once installed. Includes: -- Supplied Fan: ALLIED BLOWER & SHT MTL. SIize: 90 MH fan, 38" inlet dia, with paddle wheel blades powered by 250 HP TEFC motor, ground mounted . Note1: This fan is very versatile as it can operate from 10,000 CFM @ 6" or 7" of water SP all the way up to 40,000 CFM @ approc. 14" of water SP depending on RPM chosen. To be conservative one would keep the upper end to around 1,000 RPM. Motor could be 25 HP or 250 HP at these extremes. Being a radial blade fan it is capable of handling most materials. -- Note 2: Depending on application there is filter area capacity to add another Fan/motor for about 16,000 CFM (as per above). -- Explosion doors; walk-in access door on platform at access door. approx. 18" Rotary Air Lock (RAL) and about 38" Abort Gate with separate support stand and access platform.Features: -- 10-Gauge shell all-welded construction, Tangential scroll inlet and Inlet deflector baffle. -- All cages are unbolted to minimize damage and left in the shell. Bags are removed (to reduce weight on cages) and crated - will likely need to be laundered. -- Actual AIR CURE model is 484AC10. -- Note: Upon installation buyer is responsible for compliance to all applicable NFPA or local, state or Federal codes.Transportation also available at extra cost.

AIR CURE 484RF8 Pulse Jet dust Collector.. -- Overall Specs: 30,00 CFM @ 6.1:1 Air-to-cloth ratio, 158" dia. round baghouse with a capacity of (484) cloth filter bags (Bags not Included) of 8' length (3" x 6" oval bags provide for radial movement of bag during cleaning for longer life), 4,900 sq. ft. of filter. -- Designed for filtration media cleaning via 7.5 HP on board rotary air pump for compressed air operating at about 7.5 psi. Return air outlet and approx. 48" x 48" inlet for dust laden air. -- Filter cleaning: Rotating cleaning air manifold driven by 0.33 HP motor, (1) NEMA 9 solenoid and diaphragm valve control pulse jets of air to clean each row of bags; galvanized steel bag frames with positive bag bolt down to eliminate leakage and ride up of bags once installed. -- Includes: AEROVENT (TWIN CITY) model 330, type CBA-SW Class 4 Backward Inclined Air Handling Blower, Arrangement 9 with 100 HP TEFC motor; Explosion doors; walk-in access door on platform at top and safety ladder. -- Original cages will be removed and stored separately from the filter. Unique skirt at bottom of cyclone thus no support steel is needed and facilitates anchor bolt installation. -- Depending on application/desired air capacity it can be increased to about 44,000 CFM (@ 9:1 to Air-to-Cloth ration) but to do so will require slightly larger fan/motor. -- Needs new bags as they were discarded.

AIREWORKS - FX-15-5000: Modular Dust Collector"MOD-FLEX" Technology designs are engineered for compatibility with today's modern work cell manufacturing environments & are expandable as your business evolves. -- The "FX" series is a self-contained modular designed unit for interior use; it utilizes a dynamically balanced fan, TEFC motors, precision Laser-Cut components, and offers multiple discharge options. -- Rated at 5,000 CFM / 8.38 IWG with: 16:1 Air-to-cloth ratio. -- Equipped with: (12) 12" x 8' High-Efficiency filter bags; up with 301 sq/ft. of cloth filter area. -- Complete with: Direct drive, dynamically balanced, centrifugal fan assembly with: 15 HP TEFC Motor; Heavy-Duty machined & balanced, nonsparking impeller; 15" dia. ductwork inlet. -- Waste collection bin with pneumatic cylinder lift by air switch -- Unit comes with manual motor starter; factory installed wiring from the motor to the starter. -- Sound Level: Less than 80 dB.

AIREWORKS FX-15-5000 Modular Dust Collector. The "MOD-FLEX" technology designs are engineered for compatibility with today's modern work cell manufacturing enviroments & are expandable as your business evolves. -- The "FX" series is a self-contained modular designed unit for interior use; it utilizies a dynamically balanced fan, "TEFC" motors, precision Laser-Cut components, and offers multiple discharge options. -- Rated at 5,000 CFM / 8.38 IWG with 16:1 air to cloth ratio. -- Equipped with: (12) 12" x 8' High Efficiency filter bags up with 301 Sq. Ft. of cloth filter area. -- Complete with: Direct drive, dynamically balanced, centrifugal fan assembly with 15 HP TEFC motor; Heavy Duty machined & balanced, non-sparking impeller; 15" dia. ductwork inlet, starter. -- Sound Level less than 80 db.

AIREWORKS FX15-5000X3 Modular VFD controlled Dust Collection System. The "FX" series is a self-contained modular designed unit for interior use utilizes a dynamically balanced fan. -- "TEFC" motors, precision Laser-Cut components, & multiple discharge options with standard being plastic bags. -- AIREWORKS own Cruise Control system and how it works... Multiple machines can be connected to a single FX collector. The following example shows several machines connected to FX15-5000.Each machine can be isolated by a slide gate when not in use. If machines 1 & 2 total 4,500 CFM when they are in use, the sensor will request the Cruise Control software in the VFD to run the fan motor at the required speed to exhaust exactly 4,500 CFM. The motor will in this case run at 55.9Hz and consume 11 HP. If machine (4) starts and machine (2) shuts down, then the exhaust requirement drops to 2,200 CFM.The Cruise Control will now request the fan motor to spool down to 55Hz and the power consumption drops to 8.6HP. In this way the fan speed and power consumption will automatically be adjusted at all times to match the actual requirement. The built-in Cruise Control guarantee's that the suction is always constant at a minimum power consumption. -- Heavy Duty metal construction, fully welded plenum built using 11 Ga. steel. -- Rated at maximum 5,000 CFM pressure range from 8 - 12 IWG. Equipped with: -- (15) 8' tall High Efficiency filter bags up and (3) plastic collection bag down. -- The filter bags have 375 Sq. Ft. of cloth filter area and 21:1 air to cloth ratio with 33 Cu. Ft. of collection capacity. -- Direct drive dynamically balanced centrifugal fan assembly with 15 HP TEFC motor, 5,000 CFM, 1,750 RPM. -- Non-sparking Heavy Duty machined & balanced impeller; 15" inlet diameter. -- Manual motor starter for 230 V or 460 V. MUST SPECIFY.

AIREWORKS FX-05-2000 Modular Dust Collection System. The "FX" series is a self-contained modular designed unit for interior use utilizes a dynamically balanced fan, "TEFC" motors, precision Laser-Cut components, & multiple discharge options.Features: -- "AIREWORKS" has over 20 years of applied experience in developing & building commercial dust collection systems. -- The "MOD-FLEX" technology designs are engineered for compatibility with today's modern work cell manufacturing environments & are expandable as your business evolves. -- Heavy Duty metal constructed plenum between the top bags and bottom dust collection; rated at 2,000 CFM / 7-10 IWG with 16.7:1 air to cloth ratio. Equipped with: -- (5) 12" x 6' High Efficiency filter bags up and (3) plastic collection bag down. -- The filter bags have 125 Sq. Ft. of cloth filter area and 16.7:1 air to cloth ratio with 40 Gal. of collection capacity. Complete with: -- Direct drive dynamically balanced centrifugal fan assembly with 5 HP TEFC motor, 1,750 RPM, non-sparking Heavy Duty machined & balanced impeller; 11" inlet dia. -- Manual motor starter for 230 V or 460 V. MUST SPECIFY.PHOTO DOES NOT REPRENSENT ACTUAL MACHINE