EXTREMA PERFORMA XS-2P52 Wide Belt Sander (2) Heads;52" Width cap. Drum, Roller and Platen - 75"; Belt Lengths Head Configuration: -- 1st Head: Contact drum 30 HP motor; -- 2nd Head: Roller and Platen 30 HP motor.Features: -- Over thickness safety device -- Infeed bed rollers -- Digital thickness controller -- Individual amp meters -- Disc brakes on sanding heads -- Telemecanique electrics. -- Camozzi pneumatics -- Variable speed drive system.Specification: -- Feed motor 3 HP -- Elevation motor 0.5 HP -- Max. thickness 6" - Min. thickness 1/8" -- Contact drum 1st head 8" dia. -- Roller drum on 2nd head 5" dia. -- Dust Collection requirements 4800 CFM -- Feed speeds 15 - 50 FPM. -- Weight 6500 Lbs -- AMPS (220 V / 460 V ) 148/74.

EXTREMA - DCY-1220 L3 TYPHOON: Cyclone Filtration Dust Collection System. -- Powerful 2-stage dust collection drops out heavier dust particles through a Rotary Air Lock, allowing you to choose the disposal system before passing finer particles through the fan and filter. -- Air volume rated @ 8,800 CFM. -- Unit includes: 20 HP Motor with a Soft Start already wired in. -- Rotary air lock with: 1 HP Motor @ 38 CFM. -- Low noise operation. -- Standard support frame: LEG 3; 164" clear height x 149" clear width x 91" clear depth. Includes after filter Baghouse DC-327E. Features: 16" Inlet; (3) sections with (9) socks per section. -- Filter Socks: 6" Dia. x 70-7/8" for greater air-to-filter ratio; (1) micron filter. -- Unit is enclosed.

EZ CAR CRUSHER MODEL A --1500 hours --Opening 20 ft long x 7'6" width x 8 ft height --System Pressure 2500 psi --Port Reliefs Set At 2650 psi --Cylinders 10" bore --Travel 78" --Shaft 4" rod

EZ SANDER EZ-3760 Wide Belt SanderEZ-Sander's are built to with the ability to hold very tight tolerance (+/-.003) side to side when set up properly.Specifications: -- The sanding head is a combination head that consists of a 5" rubber-covered contact drum for the more aggressive sanding and then followed by an adjustable 2-1/2" graphite-covered felt polishing platen for doing very fine finishing sanding using a 37" X 60" abrasive belt. -- The conveyor belt speed is set to run at 10 - 30 FPM and is controlled via AC variable speed unit mounted in the main control panel. Simply adjust the dial setting to your desired feed speed. -- Double infeed and outfeed hold-down rolls are provided to help ensure proper part feeding through the Sander. -- The conveyor table/bed opening has a 0" to 5" opening allowing the operator to sand some parts as thick as 5" and the ability to sand very thin parts as well. -- Power raising and lowering of the conveyor bed is standard. -- Digital thickness display is standard.Complete with & Features: -- EZ Sander is equipped with a state-of-the-art electronic tracking system for the abrasive belt. -- Emergency stop heavy-duty caliper disc brakes bring the sanding head to a stop within 4 to 5 Sec when activated by the machine's safety interlock system. -- Limit Switches on both sides of the abrasive belt to keep the belt from over-travel. NOTE: -- Available in single phase with a 7.5 HP or 10 HP 3-Phase main drive motor. -- Voltage change to 440 Volt ...$275.

Cabinet Door Finishing System --4 Air Spray Guns --3 different lines and pumps --Paper feed belt with various speed options --Infrared sensors detect exact measurements of cabinet doors or mouldings and spray only the pieces being sent through. --System includes: (1) Dry Room and fan for air movement. --System is in great condition and works well. Our shop got to the point where we were really only using it to prime doors and it is capable of so much more than that.

FELDER G-330 EDGEBANDER0.4 - 3 mm Edge thickness cap. and 40 mm panel thickness; 3" min. width and 4-3/4" min. panel length.Equipped with: -- Quick Melt Teflon coated glue pot for granular hot-melt adhesive. -- Heavy Duty guillotine for up to 3 mm thick PVC. -- Integrated Operator PLC controls and an LCD display. -- "Anti-slip" rubberized surface chain pads.Workstations: -- Single motor, Double Blade End Trim with HF motor - 12,000 RPM. -- Top & Bottom Flush/Bevel Trim, bevels 0° - 15° (0.5 HP motor - 12,000 RPM each). -- Open space at out feed . -- Single feed speed of 26 FPM.Complete with: -- Sound & Safety enclosure over trim stations and outrigger panel support, and used tooling.NOTE: Seller states that the equipment has less than 500 hours of use!

FELDER FORMAT KAPPA 450 Sliding Table SawSpecifications: -- 126" (3,200 mm) cutting length w/scoring, anodized 14-3/4" x 126" aluminum sliding table with tracking by roller bearings, locks for easy panel loading in any position; 450 mm dia. main saw blade. -- Motorized raise, lower and tilting (0° - 45°) of blade with digital readout. -- Equipped with: -- 7.5 HP Main motor, 1.0 HP scoring motor unit w/external adjustment; square crosscut fence with (2) stops, standard rip fence with 1,250 mm (49") rip cap. w/digital readout; extension table with miter fence, and sliding outrigger support. -- Includes: -- (2) 4" Dia. dust outlets; swing away overarm saw guard.

Large table size, extendable in all three directions by up to 39" (1,000 mm) without the requirement of tools. Comfortable one-handed lever operationHeavy-duty eccentric clamp, usable on the left and right-hand side.Specifications: -- 3 HP motor, tilting head, manual hand lever control for mortise length and depth; 13" x 22" table with eccentric clamp -- 3000 RPM, reversible motor that caters for left and right cutting bits and a solid quad-jaw chuck with clamping range from 0–20 mm -- Lateral range of motion is 250 mm, cut depth is 160 mm, available height adjustment is 130 mm and there are solid locking stops in all three directions for setting precise stops.Features: 2-Jaw chuck with 5/8" capacity, Dust control collection tray below the cutter out to an 80 mm outlet,Complete with (2) adjustable and removable extension wings; fence for 90° & 45° mortises, extended stop bar on each side of table.

FELDER RL-350 Dust CollectorFelder clean-air extractors filter the air so that the dust remaining is less than 0.1mg/m cu. These exceptional air quality values are achieved by the position of the impeller. In other extracting systems, the impeller works by creating pressure between the machine and filter; with the Felder systems, the impeller is located on the clean-air side creating negative pressure throughout the system so no dust can escape. Specifications: -- 15 HP blower with 13-3/4" in-let -- Max. airflow 4,705 CFM, nominal air flow capacity 4,072 CFM -- Static pressure 9.4" WG -- Compressed air connection for automatic cleaning function. -- Dust emission quality less than mg/m cu. -- Filter surface area 71 m/sq. -- Acoustic pressure 75 dB -- Chip volume 2 x 55 gal. -- Dimension / Weight: 104" L x 45" W x 89" H, 1,785 lbs.

FIN - ST 1600, ...Top/Bottom Cleaning Brush.62" Width and 3-1/8" max. thickness opening, thickness adjustment by handwheel via worm gear with dial indicator.Equipped with: -- Top & Bottom nylon brushes driven by 3 HP drive motor (only 1-brush with machine). -- Separate variable speed feed motor with magnetic controls driving 3" dia. rubberized infeed & outfeed pinch rolls. -- Full fabricated sheet metal enclosure for efficient dust collection, dust enclosure hood with central 6" dia. dust outlet connection.

FLETCHER/DELMAC - DMG-50CB, ...Contour EdgebanderSpecifications -- Overall table size: 18" x 48"; x 39-1/4"; H; 18" x 48"; Tilting section with: 0° - 15° Tilt.Equipped with: -- 20" Dia. Coil table. -- Guillotine. -- Glue Pot & Roller. -- DELMAC Thermo-Regulator Control with: (2) WATLOW "Series 965" Digital temperature controllers; LED display & touchpad for Glue pot & roller; LCD band length counter. -- Dual foot pedal controls.

FLETCHER FM-2000 Contour EdgebanderSpecifications: 0.4 mm to 2 mm Banding thickness, up to 2" panel thickness, Unit to run strip veneer, coil, rolls of PVC, melamine, or wood veneer. Large overhead glue pot with a quick heat time of 10 minutes. Equipped with: -- Programmable temperature control with safety interlock so that applicator does not run until proper operating temperature is reached. -- 1-3/4" silicone-coated drive roll. -- Foot pedal-controlled tape advance. -- Foot pedal emergency stop. Optional Equipment: -- Power-Feed $ 2,618.00 -- 3° Manual Tilting Table $ 809.00 -- 45° Tilting Table $ 5,382.00 -- Push Button Powered Operated Tilt Table $ 6,232.00 -- Outboard Stock Support $ 1,565.00 -- 3MM Capable $ 2,950.00 -- 4"; Thickness Capacity $ 10,000.00

FLETCHER EZ-DOOR Raised Panel Door MachineThis freestanding machine can produce an entire 5-piece door in a matter of minutes. Easy to operate, the E-Z Door has a 4-position configuration to produce raised panels, cope/stile profiles and mullions for glass doors. Cathedral doors are produced by using a quick change template system.Specifications: -- Select cutter and material stop with the press of one button. -- Simple four position one spindle design. -- PLC controlled pneumatics. -- Rigid lubricated spindle assembly. -- Re-circulating ball bearing slides. -- 10 HP 230 or 460V/60HZ spindle motor – (460V/3PH=17FLA) – (230V/3PH=33FLA) -- 6,500 RPM spindle speed. -- 62 inch travel length standard with circulating ball bearing slides, cut rails to 59"; and panels to 55"; -- Includes: (4) Standard cutters (shape to be decided), others optional. -- Includes: one template of customers choice. -- 1-¼"; Arbor. -- CFM requirement is 392.Made in North Carolina, USA!

FLOW AIRE - DC-03, ...Cartridge Dust CollectorSpecifications: -- Holds (16) cartridge filters. -- Includes: New AirMax Premium Media Cartridge Filters - fire retardant. -- Total dilter media area: 3,616 sq/ft. -- Air-to-Media ratio @ 8,000 CFM: 2.21:1. -- Automatic Pulse Clean System with: Differential pressure gauge and sequencing control in enclosure. --Single Hopper outlet with Sealing Drum Cover Kit. -- Steel support structure. -- Includes: 20 HP Ground mount blower. -- Rated for :8,000 CFM. -- Motor starter & controls.Sold with a 6-Month Mechanical Warranty

FOLEY-UNITED 7460 910 Profile Knife GrinderSpecifications: -- Capacity: 12" Max. cutting circle x 12" W. -- Table size 7"; x 12"; x 34-1/2"; H. -- Table travel 12". -- Side clearance 5°, 10°, & 15°. -- Back relief angle 10° - 30°. -- Wheel O.D. 7" - 10", Wheel widths: 1/16", 1/8", & 3/16", Wheel arbor dia. 1-1/4".Equipped with: -- 2 HP - 2,850 RPM TEFC Wheelhead motor.Complete with: -- 40 mm (1.57") Dia. x 9-3/4" L Tool Arbor. -- Micro Precision Wheel Dressing System (MPDS), Swing-away.Dimensions of this specific machine 55" x 41" x 54" H.NOTE: No coolant pump.

FORESTECH ENTERPRISES - D-GR-1S: DryerDrum Dryer designed for a large Pellet plant; never put into production.Diameter (approx.): 12-3/4 Ft.Drum Length (approx.): 48 Ft.Dryer comes with Forge Tire but does not come with trunnion drives, which we can have manufactured.

FORMOSA - RSN-12, ...Straight Line Rip Saw w/Laser LightSpecifications: -- Saw dia.: 14". --Saw kerf: 3.2 - 5.0 mm. -- Max thickness: 2" -- Max. process width: Left of saw blade 250 mm; Right of saw blade 500 mm. -- Min length: 200 mm -- 3,450 RPM. -- Feed Speed: 39 or 26 MPM. -- Main motor: 7.5 HP. -- Feed motor: 1 HP. -- Machine dim.: L 1,950 mm x W 1,280 mm x H 830 mm. -- Weight: 950 kG.Equipped with Laser Light.

4INDUSTRIES 12-200 Roll Feed multiple Rip SawRoll feed multiple rip sawSpecifications: -- 12" maximum width -- 1/2" to 2" thickness -- Minimum length 16" -- Feed speed up to 200 FPM with driven bottom feed rollers, non driven top roller -- Main saw motor 40 HP -- Feed motor 7.5 HP -- Saw blade 12" diameter

FRAMA - TC-1500, ...Hydraulic Copy Lathe With One V-Gouge Copy Head and Two Manual Top Turret Heads & Knife SharpenerHydraulic Copy Lathe with (3) different speeds during execution of the work. Possibility of manual or automatic configuration on (3) intensities: 1) Regular working speed, 2) slow working speed for difficult points reproduction, and 3) fast speed to eliminate nonproductive points. Technical Data. -- Main drive motor: 6 HP. -- Hydraulic pumping unit: 2 HP motor. -- Max. turning dia.: 300 mm (12"). -- Distance between center: 1,500 mm (59"). -- Max. cross-slide speed: 9.5 MPM (30 FPM). -- Carriage return speed: 11 MPM (36 FPM). -- Copying device stroke 75 mm (3"). -- Max. hydraulic pressure between cones: 20 KG/CBM. -- Headstock taper: MT 4. -- (8) Turning speeds: 1,000 - 1,250 - 1,750 - 2,000 - 2,250 - 2,500 - 3,500 - 4,500 RPM. Also included : -- FRAMA ATC 2005 Knife Grinder: 2 HP motor. -- (1)Steady rest 70 mm (1) 18 mm and (1) adjustable for square -- Tailstock and tool holder

FRAVOL SMART S600-23 Edgebander w/Pre-Mill & Corner Rounding:Main Specifications: -- Edge & Workpiece Capacity: 0.4 - 8 mm (0.016 - 0.315") edge; 10 - 60 mm (0.394 - 2.362") panel thickness; -- 140 mm (5.512") min. panel length and 100 mm (3.937") min. panel width. -- Feed-speed, 14 or 18 MPM (46 or 59 FPM.)Front-End Equipped With: -- Pre-Milling Station (RT/S), (2) motors @ 1.1 KW (1.5 HP), 12.000 RPM, LH & RH rotation w/pneumatic programmable jump control for chip-free and clean panel edges. Standard equipped with Dia. 60 mm x 64 mm H, with diamond inserts. -- IR Panel Heat Lamp: Improves gluing bond especially during cooler ambient temperatures and humid conditions. -- Automatic Edge magazine: For strips up to 8 mm & coil stock up to 3 mm thick PVC. -- Duo Gluing System: For regular granulate Hot Melt (EVA) and easy conversion to PUR glue. "Teflon lined" glue tank with bi-directional glue roller. Automatic temperature reduction during stand-by time. Glue tank has quick release system for maintenance or quick change to a different color or glue type. -- Side Pressure Section: (3) Pressure rollers, (1) motorized, (2) idle, pneumatic pressure control and programmable NC-positioning servo motor.Work-stations: -- End Trimming (INT 2/S): (2) motor @ 0.50 KW (0.70 HP) 12,000 RPM, automatic pneumatic chamfer 0° - 15° or total exclusion from control panel. Glides 45° on prismatic linear hardened steel guides. -- Trimming Unit (RF-S/S): Top/Bottom flush/bevel/radius milling unit, (2) motors, 0.73 KW (1.00 HP) 12,000 RPM. Pneumatic remote tilt in (2) positions, postion-1 for radius and thin edges up to 0.8 mm trimming, position-2 for flush trimming up to 8 mm edges.Equipped with banding thickness gauge block feature for quick and easy set-up/changeover. Includes 1-axis NC servo control motors for programmable change-over from thin to 8 mm solid wood edges or incremental re-positioning of the cutter head. -- Corner Rounding Unit (SYNCRO 1): Compact and easy to set up for leading & trailing edges, (1) motor 0.22 KW (0.295 HP) 12.000 RPM, electronically synchronized. Working capacity, min. 10 mm, max. 60 mm panel thickness. -- Profile Scraping Unit (RB/S): Top & bottom radius scraping for PVC - ABS edges. Heavy construction to eliminate vibrations and guarantee superior edge quality. Air blow-off jets and chip collection box. -- Clean Spray System: Top/Bottom spray nozzles applies edge cleaning solvent prior to buffing. -- Glue Scraping Unit (RC/S): Top & bottom pneumatically operated glue scraping on flat panel surface to remove potential glue squeeze-out that otherwise would coat the cloth buffing discs. -- Buffing Station (GSI/S): Top/bottom (2) motors, 0.09 KW (0.125 HP) 2,800 RPM, manual, horizontal, vertical and tilting adjustment -- Hot Air Unit PHON (GP/S): Top/bottom hot air blowers to restore PVC color after scraping. Electrical power 2,000 Watt, 0° to 600° C temperature adjustment.Complete With:• PLC Program Control, with 10.7" col