NOVA TTF-6200 Dry Kiln System; Unassembled Front Load Kiln Designed to hold 5,100 bd. ft 4/4 Lumber, or 6,120 bd. ft 8/4 Lumber, Using 3/8" (9 mm) stickers. -- Specifications: Interior Dimensions: H 10' 3,5" (3.14 m), D 7'2"(2.19 m), W 25' 3" (7.7 m). -- Loading Door Opening: H 9' 10" (2.85 m), W 25' 3" (7.7 m). 1/8 " Aluminum sidewall bumpers, side hinged doors, exterior installation. -- Average 4/4 capacity: 5,100 bd. ft (12 m3) with 3/8" (9 mm) stickers. -- Average 8/4 capacity: 6,120 bd. ft (14 m³) with 3/8" (9 mm) stickers. -- Price shown is for kiln only. -- High horsepower heat requirement: 128 k BTU/hour. -- Heated Floor System, manuals and blueprints. -- Electrical Requirements: 230 VAC, 1 Phase, 60 Cycle, 25 kw/Hr max.

Unassembled Front Load Kiln with Standard Heat and Exhaust -- Interior dimensions: H 17' 6" (5.33 m), D 25' 8" (7.8 m), W 26' (7.9 m). -- Loading Door Opening: height 14'6" (4.4 m), width 25'3" (7.7 m). 1/8" Aluminum Bumper Walls, Top Hinge Door, Exterior Installation. -- Average 4/4 capacity: 25,459 Bd Ft. with 3/4" stickers. Average 8/4 capacity: 33,293 Bd Ft with 3/4" stickers. -- Price shown is for kiln only. -- Standard HP Heat requirement: 382k BTU suitable for drying dark hard woods; Optional high HP Heat requirement: 674k BTU suitable for drying softwood and white hardwoods. -- Electrical requirements: 480 VAC, 3 Ph., 60 Cy; 16.5 kW/Hr. Timber Management Control System with touch screen operator interface, data recording, remote access & networking capability. -- Features: Control room with heated air intake; 12'H x 4'D x 26'W. Top Hinge door opening System includes "230" electric chain hoist. Boiler Room: 12' W x 25' D x 17'6" H. 10' roll up & (1) access door. - Timber Dry Management Network Capability.

NOVY 1872V Multi Spindle Vertical Boring Machine 12 Spindles Vertical boring machineSpecifications: -- Table Hardwood 18" X 72' -- Table stroke 0"- 6" -- (12) Spindles in line at 5" center to center, spindle nose with 0" to 1/2" chuck -- (2) drive motor 2 HP with magnetic starter -- (4) Spring loaded hold down -- Savety guard -- Foot swtich

OAKLEY H-5 Double Sided Edge Sander. -- General Specs: With 7.5 HP -1,800 RPM TEFC motor; (2) 8-1/2" x 57-1/2" Cast Iron platens; 8" x 164" abrasive belt, 4,680 FPM belt speed. -- Equipped with: One 11" x 62" Cast iron side table on one side and (1) 19" x 64" cast table on the other side, (1) cast iron radius tilting end table, end table tilts 0 ° - 45°; 6" vertical table travel w/hand wheel adjustment. -- Features: Rubber covered direct drive pulley and idler pulley,Complete with: Magnetic starter with overload protection, (8) dead head radius ends with graphite covering, and (1) steel covered spare head roll.

OGAM - PO-340, ...Dip Chain Gang Rip Saw Specifications: -- 75 HP TEFC Motor, dip chain feed with overhead arbor. -- 4.3"; x 13.3"; Cut capacity. -- 16" Max. blade diameter. -- Power rise and fall. -- 70 mm dia. arbor. -- 2 HP Variable feed speed up to 115 FPM.Equipped with & Features: -- Automatic chain oiler. -- (3) Sets antikickback fingers. -- Adjustable infeed fence. -- Motor load meter. -- Many new saw blades.

OGAM PO/M Straight Line Rip Saw;Specifications: -- 20 HP Main motor. -- 24"; throat capacity. -- Max. cutting height: with 12" blade 3", with 16" blade 4". -- Min. diameter of circular saw blades: 8". -- Max. dia. of circular saw blades: 16". -- Min. length of working pieces: 10". -- Variable feed speed from 50 -154 Ft./minute. -- Feeding belt width: 11". -- Spindle Speed: 4,500 RPM. -- 36"; x 60"; table.Equipped with & Features: -- Fence and rail system with one stop. -- Infeed table row of anti-kick back fingers. -- Steel smooth top hold down roller. -- Top row of anti-kick back fingers. -- Steel smooth top hold down roller. -- Split hold down steel smooth roller around blade. -- Split hold down steel smooth roller around blade. -- Steel smooth top hold down roller. -- Chain is in excellent condition!

OGAM MODEL PO-340 DIP CHAIN GANG RIPSAW ( THis is a Parts machine only )Specifications: -- 60 HP arbor motor, dip chain feed with overhead arbor, 13-3/8" (340 mm) max. rip cap. (between saw blades), 12-5/8" chain width. -- 9-13/16" Mn. to 13-7/8" max. blade dia., 4-3/4" max. depth of cut (manual raise and lower of the spindle), 70 mm dia. arbor runs @ 4,200 RPM; min. board length 19-3/4" (without short stock feed plate-see photo). -- Variable speed belted feed motor 20 to 100 FPM (approximate).Note From Seller: Ogam Gang Rip Saw. 60 HP motor 230/460. I don’t know much about this machine. Bought it used but haven’t been able to hook it up due to our current electrical service. The person I bought it from says it ran well when taken out of service. Can load on a truck.

OGDEN PUR LAMINATING LINE for Engineered FlooringSystem consists of:POS 1. PLYWOOD HOPPER FEEDER Plywood boards (two-track or single-track) are loaded vertically into the hopper and push-fed from the hopper into the Roll Coater where the rolls from the Coater take over feeding the plywood. The plywood hopper feeder is centered to the press; adjustments of the fence are via hand crank where both sides of the fence move simultaneously. The hand crank has a digital indicator to assist the operator in the width setup. Specifications:Length 4 ft to 8 ftWidth with single track 6" to 12"; tolerance of +/- 1/64";Width with double track 3" to 7" tolerance of +/- 1/64";Hopper capacity height 16";Pass line-height 37"; POS 2. DRUM MELTER Drum melter melts the glue which is contained in a 55-gallon drum, it pumps the glue out through heated hoses and delivers the glue to the roll coater. The roll coater sends the drum melter signals when to pump glue and when to run the pump off, a signal is sent according to glue level height. POS 3. TOP HEAD PUR ROLL-COATER Roll coater to apply hot melt PUR glue to the top of the Substrate. Roll coater will be equipped with wheel casters in order to move the unit out of the line for cleaning. Touch Screen Control panel for the coater is mounted on the left-hand side when facing the in-feed of the unit. Adjustment of doctor roller will be with hand wheel (not powered) and mechanical digital display in increments of 0.001" in relationship to application roller. Adjustment of the coating roller will be powered and will include a hand wheel with a mechanical digital display in increments of 0.001" Roll coater is equipped with a fume extraction hood which is located above the roll coater. Feed speed 20 - 250 FPMMin coater length 21"Maximum thickness 4"Minimum thickness 3/8"Effective coating width 14"Doctor roller ground chromeCoating roller silicone, 60 durometerVoltage 480 VPass line height 37"; POS 4. PLYWOOD TRANSFER CONVEYOR Conveyor length 20’Veneer lengths 2’ to 12’ ’Width with single track 7" to 12"; tolerance of +/- 1/64";Width with double track 3" to 7" tolerance of +/- 1/64";Pass line-height 37";Feed speed range from 20 to 250 FPMPop up gate will be installed to st

OLIVER 4045 12" PROFESSIONAL TABLE SAW, with 36" FenceHeavy-duty cast iron table precision ground for accuracy; rugged machine frame construction provides maximum stability and reduced vibration.Specifications: -- 12" Blade capacity and 0° - 45° tilting arbor with digital read-out. -- 7.5 HP Motor at 3,450 RPM. -- Complete with: 52" rip fence capacity that will handle most of your work. -- 48" x 52" Cast iron table. -- Blade guard, miter gauge, push-button controls. -- Parts list & operation manual.

OLIVER 4016 10" Table Saw, 5 HP, 3-Ph w/36" Rail Specifications: -- 5 HP motor; poly V-belt drive system with belts that run smoother and with less vibration, giving you the highest quality cut available. -- Top it all off with with OLIVER'S Optimus square tube fence and a digital blade angle readout system and you've got a saw that tears it up with accuracy and in style! -- Model 4016.004 5 HP, 220V. 3-Phase.

OLIVER 5385 Single Head Wide Belt SANDER (37") 1-Head and 37" belt width Combination Sanding Head with rubber covered contact roll and adjustable finishing platen, 1/8" - 5" Thickness capacity, 36" width capacity.Specifications: -- 20 HP Main drive motor. -- 1 HP Variable speed (15 to 45 FPM). -- 1/4 HP Power raising and lowering conveyor bed motor. -- 37" X 75"; Abrasive belts for longer life and less loading.Features; -- Central control panel features digital thickness set-up control for accurate stock height and removal. -- Four post lift design assures accurate consistent results. -- Oscillating belt is controlled by an air sensor to prevent sanding lines. -- Finishing Platen is fully adjustable and can be removed. -- Multiple dust ports for efficient dust management. -- Independent motors run the sanding belt, feed conveyor, and table elevation for maximum power to each operation.

OLIVER 6910 Oscillating Spindle SanderPedestal style Spindle Sander constructed for rugged use .Specifications: -- 2 HP Motor drives and is connected through a flexible coupling, and can be installed or removed without disturbing the drive mechanism. -- Spindle speed 1,725 RPM, Oscillation speed 75 Cy/Min with 1-1/2" stroke length. -- Spindle quill runs in precision ball bearings, oscillated by a heavy duty worm & gear mechanism running in a bath of oil. -- (10) Spindle sizes provided: 1/4 x 5", 3/8 x 6", 1/2 x 6", 5/8 x 6", 3/4 x 9", 1 x 9", 1 1/2 x 9", 2 x 9", 3 x 9" and 4 x 9"; 100 grit abrasive sanding sleeve with each spindle. -- Large 24" x 24" precision ground cast iron table mounted on large trunnions that can be tilted 45° down and 30° up by use of a convenient handwheel. -- Complete with: Pedestal style stand.

OLIVER - 34-DD, ...Disc Sander (Double)(2) 30" Dia. steel discs; 5 HP double shafted motor turns @ 1,050 RPM.(2) Steel side tables, 40" x 15", (1) slotted and (1) plain; both tables tilt 10° up and 45° down.(1) Table with 6" manual vertical adjustment; rack travel adjustment by screw & crank. -- Complete with: Magnetic controls; (2) dust outlets; large handwheels for easy adjustments.

OLIVER 4705 SHAPER 5 HP, Sigle phase or 7.5 HP, 3-PhSpecifications and Features: -- Massive cast iron precision ground table provides a solid work surface. -- Cast iron base provides a steady platform. -- 3/4"; and 1-1/4"; interchangeable spindles are included for added versatility. -- Three spindle speeds allow more choices to produce a better finish. -- Reversing spindle gives more options for each set-up. -- Innovative dovetail design accurately raises and lowers the spindle. -- Fence is independent and features micro adjustments for quick set-up. -- Top mounted control panel includes a digital readout for spindle height. -- Large hand wheel for quick spindle height adjustment. -- Magnetic controls with emergency off switch for safer operation. -- Includes miter gauge. -- Spindle Speeds: 5,000, 7,000 and 10,000 RPM. -- Maximum Tool Diameter: 7"; Below Table, 8"; Above Table. -- Spindle Diameter: 1-1/4"; and 3/4"; Interchangeable. -- Vertical Spindle Travel: 4". -- Table Height: 36-1/2". T-Slot: 3/4" x 3/8". -- Dust Port Diameter: 4". -- 800 CFM min. -- Optional collet for router bits available special order --[1/2" Spindle for Models 4705 & 10047 Shaper]1/2" Spindle for Models 4705 & 10047 Shaper$89.99Model 10047[3/4" Spindle for Models 4705 & 10047 Shaper]3/4" Spindle for Models 4705 & 10047 Shaper$89.99Model 10047[1" Spindle for Model 4705 Shaper]1" Spindle for Model 4705 Shaper$99.99Model 4705[1/4" Collet for Models 4705 & 10047 Shaper]1/4" Collet for Models 4705 & 10047 Shaper$69.99Model 4705[1/2" Collet for Models 4705 & 10047 Shaper]1/2" Collet for Models 4705 & 10047 Shaper$59.99Model 4705[1-1/4" Spindle for Model 4705 Shaper]1-1/4" Spindle for Model 4705 Shaper$99.99Model 4705 prices may vary.

OLIVER 4430 20" PLANER WITH HELICAL HEAD20" Maximum stock width cap., 1/4" to 8" max. stock thickness, 10" minimum stock length. Equipped with: -- 5 HP Main drive motor and mechanical raising and lowering of the cutter head. -- Fixed bed height of 29-7/8". Table dimensions 20"L X 21"W. Overall all table dimensions with infeed and outfeed bed extensions 51"L X 21"W. -- 3-1/4" Dia. Helical Cutter Head with 4-sided carbide inserts. -- Auto-Depth lock via nitrogen-charged cylinders eliminates snipping. -- 8" Max. thickness adjustment via handwheel includes LED Digital readout for head positioning. -- 4-Post support for proper head alignment.Complete with: -- 5" Dust outlet and built-in mobile base for ease of movement

OLIVER 15" Planer with Helical Cutterhead - 10014, 3 HP (Single Phase)Unique design allows motor and cutter head to move in unison.Specifications: -- Auto-depth lock features twin nitrogen cylinders virtually eliminates snipping. -- Helical cutter head with premium carbide inserts. -- 4-Sided cutting inserts are indexed and easy to replace. -- Heavy cast iron construction including extension wings. -- Table and extensions wings are precision ground for smooth stock feeding. -- Table is fixed allowing easy use of auxiliary stock support. -- Wixey digital read-out allows precise thickness settings. -- Large handwheel and support struts allow easy height adjustment. -- Four-post design ensures head alignment regardless of stock thickness. -- Two-speed feed gearbox for better cuts, Oil bath gear lubrication for years of performance.Complete with: -- 4"; Port allows excellent dust management. -- Built-in mobile base allows easy movement in the shop. -- Magnetic switch for added protection and safety.

22"; Planer with Byrd Shelix Cutterhead - 4455B, 7.5 HP shingle phase or 10 HP, 3-phBYRD Shelix carbide inserts are indexed for quick changing.Specifications: -- Max depth of cut 3/16", min. part length 10"; max. work pc dims 22" w x 9" thickness. -- (2) Adjustable Bed Rollers, plus one infeed and one outfeed roller. -- Cutterhead speed 5,000 RPM and head is equipped with (110) Byrd knife inserts. -- 2-Speed gearbox provides the perfect feed rate of 20 and 30 FPM.Features: -- Massive cast iron construction throughout. -- Polished built-in table roller assists movement of rough stock. -- Segmented infeed roller and sectional chip breaker easily handles rough stock. -- Magnetic controls with emergency off switch for safer operation. -- Digital readout allows precise thickness settings. -- Hinged access to cutter head and feed rollers for quick set-up. -- 3 V-belt drive smoothly transfers power to drive train and cutter head. -- Easy access to the motor, drive train, and gearbox assists in maintenance and adjustment. -- 5"; Dust chute easily handles chip removal (requires approx. 900 CFM) -- Powerful EFC motor available in single or three-phase. -- Single phase motor 7.5 HP, 220V Only (38 Amp)

OLIVER 4470 25" Straight Knife Planer Full 24" of cutting width, over 9" of cutting capacity, and the ability to take up to 1/4" off in a single pass through the 4-knife standard cutter head, this planer will take whatever you can dish out. -- The Digital Thickness Controller and Powered Table Travel eliminate guesswork, make dialing in settings a breeze. But ease of operation isn't everything, this OLIVER outputs stock that's true and straight. -- A Sectional Infeed Roller and Chip Breaker apply uniform pressure on uneven stock, coupled with a Driven Outfeed Roller to keep your stock in place. -- And a powerful 10 HP motor Single Phase motor, or 15 HP 3-Phase motor. --OPTIONAL EQUIPMENT: Byrd Shelix Cutterhead (ADD $2,400)

OLIVER - 299-D, ...24" Planer (8" thickness capacity) -- Capacity: 24" x 8" Thick planes stock as short as 11". -- 3-Knife steel cutterhead motor: -- 5 HP; 3 PH. -- Sectional infeed rolls: - (12) 2" Wide sections: Sectional chip breaker. -- (12) 2" Wide sections with: 1/4" Independent Lift. -- (2) Driven bed rolls; feed motor: 1 HP - 3 PH REEVES Variable speed 15 - 60 FPM.

OLIVER 2019 Wood Turning Lathe;This lathe brings the lathe back to the OLIVER line, in true OLIVER Fashion! -- Starting with a solid, stable cast iron base, legs, bed, tool rest, and headstock. -- OLIVER adds a powerful reversible 2 HP motor with a wide speed range for a variety of tasks. -- A frequency inverter and RPM Digital Readout give you an accurate read on your speed so you can precisely adjust for any particular job.Specifications: -- 41" Between Centers, 18" Swing over bed, 40" Swing Outboard; -- Spindle Speed 200 - 2,400 RPM, Front Faceplates 6". (2).Features: -- One of the best features on the lathe is the In-board and Out-board headstocks (slides on the bed), enabling you to work on very large Bowls and most anything else you need to turn. The slide extension can increase the center distance to 57" with optional extension bed.Includes: -- Integral spindle index for (36) positions.Dimesniosn/Weight: 46.5"long x 19.5" depth x 49.25" height. Approx. 415Lbs.Available Options: -- Bed extension that mounts in two positions....Protective Safety Guard. Assembly.... Please call. -- See attached literature for more specifications.