CANTEK MX350 EDGEBANDER (W/ PRE-MILLING): -- Specifications:0.4-3 mm Edge thickness, panel thickness 8~45 mm, min. panel width 100 mm (4″), min. panel length 170 mm (6.7″). Equipped with: -- Quick melt Teflon coated glue pot 2.5 Lb capacity. Two spring loaded pressure rollers (One driven, one idling). Automatic coil feed PVC/ABS up to 3mm thick, pneumatically operated guillotine. Laminate strip material can be hand-fed. PLC control system with LED display and keypadWorkstations: -- Pre-Mill station with (2) 1.1 Kw 12,000 RPM trim motors 32 mm (1.25") max. material thickness. -- Single motor front and rear edge trim station. -- Top & bottom trim station with insert knife cutters for radius trimming & bevel trimming. -- Top & bottom scrape station 2 mm radius. -- Top & bottom buffing. -- Feed speed 29 FPM

CANTEK MX-370P EDGEBANDER (W/ PRE-MILL & CORNER ROUNDING): --Specifications:0.4 - 3 mm Edge thickness, panel thickness 0.315" - 1.77". Minimum panel length 6.7", minimum panel width 3-¾". Heated infeed fence for better glue adhesion. Fixed feed speed 29 FPM.Equipped with: -- Pre-mill (2) 1.5 kW each (12,000 RPM) counter-rotating cutter-heads for removing up to 3mm of the panel edge. -- Quick change 1.2 kg Teflon-coated glue pot is designed for EVA hot-melt glue. The glue pot is a Quick-Change type and can be removed and replaced in less than 1 minute. -- Guillotine shear: The guillotine shear can rough trim coiled material up to 3 mm in thickness. Pressure rollers section consist of one large driven roller, followed by a smaller one. Workstations: -- End Trim: The end trim system is a single motor with (2) saw blades. The unit is mounted on high-precision linear guide rails. -- Top & bottom trimmers with (2) high-frequency motors for top & bottom trimming of the panel. Each motor has an inset knife cutter-head which can be adjusted from flush to beveled finish for thin edges, and radius trimming (2 mm radius). Single motor Corner Rounding Unit Can process between 0.4 - 3 mm and up to a board thickness of 1.77" (45 mm). The multifunctional cutter can round straight or radius edges with a 2 mm radius cutter. -- Radius scraping unit fine-tunes the edge radius while removing knife marks during the milling process on radius edging. Insert knives have a 2 mm radius. -- Buffing unit leaves a super finish on ABS and PVC edging and removes any discoloration on the edges.

CANTEK - PCM 120, ...Hollow Chisel MortiserFeatures: -- Power stroke of head permits easy, fast, and accurate successive cuts. -- Separate fan blower to keep work clean and free from dust & chips. -- Manual adjustable table height and lateral position. -- Heavy-Duty cast iron construction. -- Convenient centralized control panel. -- Foot pedal actuated cycle. -- Pneumatic workpiece clamping by lever.Specifications: -- Chisel range: 1/4" - 3/4"; Motor; 2 HP; Spindle speed: 3,400 RPM. -- Table: 16-3/4" x 21-1/4; Table tilts 30°. -- Air pressure: 8kG Clamping; Cylinder: 2-1/2"; (63 mm). -- Head traveling cylinder: 3.15"; (80 mm); Table cross travel: 5";. -- Table longitudinal travel: 18";; Table vertical travel: 12";. -- Max. stock width: 12";; Max. mortising depth: 4";. -- Machine weight: 572 Lbs. -- Shipping weight: 726 Lbs; Shipping dimension: 35"; x 38"; x 70"; (880 x 960 x 1,780 mm).

CANTEK - GT635ARD-16 25″ Double Surface Planer25″ Wide x 16″ thickness capacity Add on $2,500 for increase HP of top head to 30 HPFeatures: -- Cutterheads are spiral insert types with six (6) rows of carbide inserts. -- (2) Driven and (1) idle bedroll for superior feeding of even difficult material. -- Swiveling control panel for more ergonomic access to machine controls. -- Inverter variable speed control with feed speeds from 26 to 80 FPM. -- Easy to access external handwheel adjustment of infeed bed. -- Hard chromed worktable for high wear resistance. -- Auto lubrication to conveyor chain, central lubrication for dovetail elevation guideways. -- Sectional chip breaker and sectional feed roller before top cutterhead.. -- Rubber outfeed top roller to prevent chip marking. -- Over thickness safety shut-off bar across infeed. -- Ammeter for each motor on the control panel to monitor motor load.Specifications: Maximum working width 25″Maximum working thickness 16″; Minimum thickness 0.394"; Min. workpiece length 12.2″Bottom head motor 20 HP, Top planing head motor 25 HP - Feed motor 5 HPTable elevation motor 1/2 HP.Cutterhead diameter 4", Knife dimensions 30 mm x 12 mm x 1.5 mm w/bevels (96 pcs per head)Cutterhead speed 5400 RPM;Feed speed (variable) 26 - 80 FPMDust ports 2 @ 6";; Table dimensions 27" x 103" (41.85" from the floor);Machine voltage 460/3/60 = 70 amps.Dims & Weight (LxWxH) 105″ x 45.1″ x 92.9″; (max.) Net weight 6700 Lbs,Packaging dimensions 109″ x 49″ x 89″; Gross weight 7800 Lbs

CANTEK GT610HI CARDAN SHAFT DRIVE DOUBLE SURFACE PLANERSpecifications: -- Max. working width 24" (610 mm). -- Max. working thickness 8" (200 mm). -- Min. working thickness 5/16″ (8 mm). -- Min. working length 12" (300 mm). -- Cutterhead RPM 5000 RPMCutterhead diameter 5.3" (135 mm). -- Feed speed 30-98 FPM 10 – 30 m/min. -- Top cutterhead motor 40 HP. -- Bottom cutterhead motor 30 HP. -- Feed motor 5 HP. -- Table Rolls 7 (3) driven. -- Opening hoist motor 1 HP. Machine dimensions: (LxWxH) 112"; x 67"; x 67"; 2830x1700x1700mm . Machine weight 8800 Lbs 4000 kgsShipping weight 9240 lbs 4200 kgs. -- Shipping dimensions (LxWxH) 115"; x 75"; x 75"; 2900 x 1900 x 1900mmMachine electrics (Standard) 460/3/60 = 110 amps (Other voltages on request, factory order)Key Advantages• Cast iron machine frame for superior vibration damping resulting in a long machine & bearing life.• Chrome-plated tables and top and bottom for maximum wear resistance.• Cutterheads are mounted in precision ABEC 7 RHP bearings.• The feed system uses a spring-loaded pin arrangement to pass material over the bottom jointing head.• Sectional serrated infeed roll before the top cutterhead.• Variable feed speed by frequency inverter (VFD) with digital display for the feed speed.• Digital thickness control for quickly and precisely setting the desired thickness.• The upper assembly is adjusted for desired thickness by four large-diameter cylindrical posts.• Adjustable infeed bed by easily accessible handwheel to set desired stock removal on the bottom head.• Easy to access swivel control panel with individual ammeters for load monitoring and hour meter to aid in maintenance planning.• Cutterhead starters are Y-Delta providing a soft start to the heads for reduced power consumption on startup.• Automatic lubrication to the conveyor feed system.• High-quality Schneider electrical components to CSA/UL standard.

CANTEK - GT635ARD-8 25″ Double Surface Planer25″ Wide x 8″ thickness capacity Add on $2,500 for increase HP of top head to 30 HPFeatures: -- Cutterheads are spiral insert types with six (6) rows of carbide inserts. -- (2) Driven and (1) idle bedroll for superior feeding of even difficult material. -- Swiveling control panel for more ergonomic access to machine controls. -- Inverter variable speed control with feed speeds from 26 to 80 FPM. -- Easy to access external hand wheel adjustment of infeed bed. -- Hard chromed worktable for high wear resistance. -- Auto lubrication to conveyor chain, central lubrication for dovetail elevation guideways. -- Sectional chip breaker and sectional feed roller before top cutterhead.. -- Rubber outfeed top roller to prevent chip marking. -- Over thickness safety shut-off bar across infeed. -- Ammeter for each motor on the control panel to monitor motor load.Specifications: Maximum working width 25″Maximum working thickness 8″; Minimum thickness 0.394"; Min. workpiece length 12.2″Bottom head motor 20 HP, Top planing head motor 25 HP - Feed motor 5 HPTable elevation motor 1/2 HP.Cutterhead diameter 4", Knife dimensions 30 mm x 12 mm x 1.5 mm w/bevels (96 pcs per head)Cutterhead speed 5400 RPM;Feed speed (variable) 26 - 80 FPMDust ports 2 @ 6";; Table dimensions 27" x 103" (41.85" from the floor);Machine voltage 460/3/60 = 70 amps.Dims & Weight (LxWxH) 105″ x 45.1″ x 92.9″; (max.) Net weight 6700 Lbs,Packaging dimensions 109″ x 49″ x 89″; Gross weight 7800 Lbs

CANTEK - GT400BRD 16″ Double Surface PlanerGeneral description: -- Spring-loaded conveyor pin system ensures material is passed over the bottom cutterhead to resulting in a flat and uniform board prior to planning to thickness on the top head. -- Spiral insert knife cutterheads with two-sided solid carbide knives produce a smooth finish with increased stock removal capacity and extremely quiet operation. -- Heavy-duty cast-iron machine body and table for vibration-free cutting.Digital electronic thickness adjustment in INCH and MM (Inch = 0.001"; / mm = 0.01mm resolution) for precise thickness control KEY ADVANTAGES SERVICESpecifications: -- 16″ Wide x 6.7″ thick planing capacity -- 10 HP Bottom Head and 15 HP Top Head -- Cutterheads are spiral insert types with six (6) rows of carbide inserts. Cutterhead speed 5,400 RPM. (2) Driven and (1) idle bed roll for superior feeding of even difficult material. -- Swiveling control panel for more ergonomic access to machine controls -- Inverter variable speed control with feed speeds from 26 to 80 FPM, 2 HP variable feed drive.Features: -- Easy to access external handwheel adjustment of infeed bed -- Hard chromed worktable for high wear resistance -- Auto lubrication to conveyor chain, central lubrication for dovetail elevation guideways -- Section chipbreaker and sectional feed roller before top cutterhead -- Rubber outfeed top roller to prevent chip marking -- Over thickness safety shut-off bar across infeed. -- Ammeter for each motor on control panel to monitor motor load -- Star-Delta soft start.

CANTEK CM626 Single-Sided Planer with Helical Head26" x 11-3/4" capacity Planer w/Helical Cutter HeadFeatures: -- Spiral cutterhead with (6) rows insert knives provides high removal, superior finish, and low noise. -- Solid cast iron construction. -- Variable feed speed. -- Drive top and bottom feed rolls. -- Front & rear bed rollers easily adjusted from the front of the machine. -- Power table elevation by digital thickness control. -- Serrated solid infeed roll. -- Section chip breaker. -- Anti-kickback fingers for added safety. -- Dual heavy jack screws with slides for accuracy & rigidity. -- Dust/Chip exhaust outlet 6"; in diameter. -- Sound dampening machine cover. -- All operations on a convenient control panel. -- Two-sided solid carbide inserts are easily changed while providing optimum wear lifeSpecifications: -- Maximum planing width 26" -- Maximum planing thickness 11 ¾" -- Minimum planning thickness 0.15"; (4 mm) -- Maximum depth of cut 0.31"; (8 mm) -- Minimum planning length 10.35" (263 mm) -- Table area 35" x 27" -- Feed speeds variable 16 – 70 FPM -- Main motor 20 HP -- Feed motor 1 HP -- Table motor 1/2 HP -- Knives 30 x 12 x 1.5 qty 100 -- Cutterhead 4 ¾" dia. x 5000 RPM -- Top feed rollers 3" dia. -- Dust hood outlet 6" dia.

CANTEK MX340M Edgebander (Single Phase):The MX340 from CANTEK is designed to be a compact, and durable edgebander. -- Equipped with end trimming, flush trimming, PVC scraping, and buffing. -- The CANTEK MX340 Edgebander is operated through a PLC control system with an LED display and keypad.Specifications: -- The MX340 handles panel thiknesses of 0.315" up to 1.77" (8 mm to 45 mm). -- The coil feed accepts edgebanding from 0.4 mm to 3 mm thick, and strip material can be hand-fed. -- Conveyor feed speed is 29.5 FPM (fixed).Work stations: -- Heated infeed fence for optimum glue penetration. Large capacity Teflon coated glue pot (2.64 Lbs). -- Pneumatically operated guillotine for up to 3 mm thick banding, followed by spring loaded double pressure rollers. -- Single front/rear trimming unit 0.3 HP motor. -- Double top and bottom trimming units (2) 1/2 HP motors. -- Top and bottom scraper/radius scraper. -- Top and bottom buffing station (2) 0.16 HP motors.Also available in 220V/3PH/ 60 Hz

CANTEK - GOODSPEED CP-1250 AP Hydraulic Copy Lathe. -- General Data: 44" Length cap. with 4" min. length of stock and 1/2" - 4" max. diameter cap., hopper feed with automatic chucking, square or round stock can be hopper fed. -- Equipped with: 7.5 HP Spindle motor, 1,800 - 3,200 RPM spindle speed adjustable by pulley change, 3 HP hydraulic motor. -- Complete with: Swivel control panel, PLC sequence controller built into separate control cabinet, (3) pressure gauges, automatic way & support collar lubrication & safety wire mesh across the front of machine. -- Includes: Two hydraulic copiers (rough + fine). Travelling steady rest and installed knives. -- Production capacity: Approx. (5 - 7) pieces/Min for 600 mm length, (3 - 5) pcs./Min for 900 mm length, (2 - 3) pcs./Min for 1,200 mm length, depending on cutting speed, type of material, etc. -- Electrical load: 11.4 amps, 10.5 HP @ 575/3/60.volts.

CANTEKK UFO-105B --Specifications: --7.5 HP generating up to 2863 CFM. -- --Base is mounted metal base

CANTEK MRS 300 Chain Feed Gang Rip Saw.General Description: -- Frame is Cast Iron, all the main parts are enclosed, ensuring protection and perfect stability. -- Straight line caterpillar style feeding with heavy guided chain. Chain blocks are special cast iron with heat treated & precision ground pins. -- Nickel chrome steel Saw Arbor with 70 mm OD – dble. keyed quick removal sleeve.Features & Includes: -- (3) Sets of Anti-Kickback Fingers, (2) top, (1) bottom. -- Powered Rise & Fall to the pressure rollers. -- New style round Fence Bar support with quick shift long fence. -- Automatic Centralized lubrication system. -- Automatic STAR-DELTA Starter (slow speed start) and low voltage controls. -- CE Style European guard & safety features. -- Long fence for control of long material.Specifications: -- Max. Working Thickness of 4 5/8"; (120 mm) with 15"; Blade diameter. -- Min. Length of 20"; standard or 12" with short stock attachment. -- Saw Sleeve Usable Length (between outside saws) is 12" (305 mm). -- Saw Blade Diameter is 200 - 350 mm (8"; - 14";). -- Saw arbor sleeve OD (diameter) is 70 mm; Saw arbor diameter is 50 mm. -- Saw arbor vertical adjustment is 3.6"; (90 mm). -- Saw Motor is 50 HP – Saw Arbor Speed is 3,800 RPM. -- Powered Pressure Rollers (Rise/Fall), 0.5 HP motor. -- Feed Speeds from 25 - 100 FPM (8 - 39 MPM); Feed Motor has 2 HP drive. -- Table Size is 30"; x 60"; Table Height from floor 33-1/2". -- Included: FP INDUST. Laser light on infeed, (2) 6"; Dia. Dust Hoods and (1) Removable saw sleeve, (1) set of spacers.NOTES: It still has the original packing grease on it.

CANTEK MX350 Edgebander w/Premilling0.4-3 mm Edge thickness, panel thickness 8 ~ 45 mm, min. panel width 100 mm (4″), min. panel length 170 mm (6.7″). Equipped with: -- Quick melt Teflon coated glue pot 2.5 Lb capacity. Two spring-loaded pressure rollers (One driven, one idling). Automatic coil feed PVC/ABS up to 3mm thick, pneumatically operated guillotine. Laminate strip material can be hand-fed. PLC control system with LED display and keypadWork stations: -- Pre-Mill station with (2) 1.1 Kw 12,000 RPM trim motors 32 mm (1.25") max. material thickness. -- Single motor front and rear edge trim station. -- Top & bottom trim station with insert knife cutters for radius trimming & bevel trimming. -- Top & bottom scrape station 2 mm radius . -- Top & bottom buffing. -- Feed speed 29 FPM

CANTEK MX340M Edgebander (Single Phase) --The MX340 from CANTEK is designed to be a compact, and durable edgebander. -- Equipped with end trimming, flush trimming, PVC scraping, and buffing. -- The CANTEK MX340 Edgebander is operated through a PLC control system with an LED display and keypad.Specifications: -- The MX340 handles panel thickness of 0.315" up to 1.77" (8 mm to 45 mm). -- The coil feed accepts edgebanding from 0.4 mm to 3 mm thick, and strip material can be hand-fed. -- Conveyor feed speed is 29.5 FPM (fixed). --Work stations: -- Heated infeed fence for optimum glue penetration. Large capacity Teflon-coated glue pot (2.64 Lbs). -- Pneumatically operated guillotine for up to 3 mm thick banding, followed by spring loaded double-pressure rollers. -- Single front/rear trimming unit 0.3 HP motor. -- Double top and bottom trimming units (2) 1/2 HP motors. -- Top and bottom scraper/radius scraper. -- Top and bottom buffing station (2) 0.16 HP motors.

CANTEK MX340 EDGEBANDER (COMPACT): (Single Phase)The CANTEK "MX340" is designed to be a compact and durable Edgebander. -- Equipped with: End trimming, flush trimming, PVC scraping, and buffing. -- Edgebander is operated through: PLC Control System, LED display, and keypad.Specifications: -- Panel thickness cap.: 0.315" to 1.77" (8 mm to 45 mm). -- Edgebanding coil feed accepts: 0.4 mm -3 mm Thick; strip material can be hand-fed. -- Conveyor feed speed: 29-1/2 FPM (fixed).Workstations: -- Heated infeed fence for optimum glue penetration; large capacity Teflon coated glue pot (2.64 Lbs). -- Pneumatically operated guillotine: 3 mm Max. thick banding; followed by spring loaded double pressure rollers. -- Single front/rear trimming unit: 0.3 HP Motor. -- Double top & bottom trimming units: (2) 1/2 HP motors. -- Top & bottom scraper/radius scraper. -- Top & bottom buffing station: (2) 0.16 HP Motors.

CANTEK MT-610 24"; Rotary Milling PlanerSpecifications -- Heavy duty welded steel construction. --Moving table type -- Display position number. -- Alarm bell and flash light. -- Speed change for feeding, controlled by Inverter (VFD) -- Rubber Endless Belt. -- Automatic device for feed belt tracking. -- Air jet cleaner for cutter -- Working width 610mm -- Workpiece thickness 3-125mm Equipped with & Features -- Number of cutters 2 units -- Spindle motor power 20 HP -- Brush motor power 1 HP (150 mm dia) -- Vacuum motor power 1 HP (suction for conveyor belt) -- Feed motor power 1 HP -- Lifting motor power 0.5 HP

CANTEK MX340 Edgebander (Single Phase)The MX340 from CANTEK is designed to be a compact, and durable edgebander. -- This machine is equipped with end trimming, flush trimming, PVC scraping, and buffing. -- The CANTEK MX340 Edgebander is operated through a PLC control system with an LED display and keypad.Specifications: -- The MX340 handles panel thicknesses of 0.315" up to 1.77" (8 mm to 45 mm). -- The coil feed accepts edgebanding from 0.4 mm to 3 mm thick, and strip material can be hand-fed. -- Conveyor feed speed is 29.5 FPM (fixed).Work stations: -- Heated infeed fence for optimum glue penetration. Large capacity Teflon coated glue pot (2.64 Lbs). -- Pneumatically operated guillotine for up to 3 mm thick banding, followed by spring loaded double pressure rollers. -- Single front/rear trimming unit 0.3 HP motor. -- Double top and bottom trimming units (2) 1/2 HP motors. -- Top and bottom scraper/radius scraper. -- Top and bottom buffing station (2) 0.16 HP motors.

CANTEK - MX340, ...Edgebander (Single Phase)The CANTEK "MX340" is designed to be a compact and durable Edgebander. -- Equipped with: End trimming, flush trimming, PVC scraping, and buffing. -- Edgebander is operated through: PLC Control System, LED display, and keypad.Specifications -- Panel thickness cap.: 0.315" to 1.77" (8 mm to 45 mm). -- Edgebanding coil feed accepts: 0.4 mm -3 mm Thick; strip material can be hand-fed. -- Conveyor feed speed: 29-1/2 FPM (fixed).Workstations -- Heated infeed fence for optimum glue penetration; large capacity Teflon coated glue pot (2.64 Lbs). -- Pneumatically operated guillotine: 3 mm Max. thick banding; followed by spring loaded double pressure rollers. -- Single front/rear trimming unit: 0.3 HP Motor. -- Double top & bottom trimming units: (2) 1/2 HP motors. -- Top & bottom scraper/radius scraper. -- Top & bottom buffing station: (2) 0.16 HP Motors.

CANTEK C251 24" WIDE BELT SANDERSpecifications: -- 24" Width cap. - sanding head with a rubber covered contact roll and adjustable finishing platen, 10 HP motor main drive motor. -- 25" x 60" Abrasive belts, pneumatic abrasive belt tensioning. -- 0" - 5.9" thickness capacity, Power elevation for thickness opening with digital thickness programming. -- Variable conveyor feed speed from 15 - 50FPM, 1 HP feed motor. -- 5.9" Max. working thickness, 13" min. working length, -- Spring loaded holddown rolls.Complete with: -- Magnetic controls, (2) 4" dia. dust collection outlets, and safety shutoff. - 825 CFM Dust collection required. Optional: 10 HP Single Phase motorElectronic belt tracking for optimum belt life and sanding results. Ammeter for load monitoring main drive motor. Disc brake on the main motor. Pneumatic belt tensioning with quick release outboard support. Safety Interlocks are located on all access doors.

CANTEK - P-630HV, ...24" Single Sided Planer with Spiral Knife CutterheadSpecifications: -- Planing width: 24-3/4"; planing thickness: 3/8" - 11-13/16". -- Max. depth of cut: 5/16". -- Min. length: 8-3/4". -- Table size: 26-1/2" x 33-1/2". -- Cutterhead speed: 5,600 RPM. -- Variable feed speeds: 20 - 39 FPM. Equipped with: -- 98 mm (3.86") Dia. Steel spiral knife cutterhead with: (6) Rows of (86) 30 x 12 x 1.5 mm inserts mounted on angle for shear cut & 10 HP Motor. -- 3" Dia. Sectional infeed roller with: 1 HP Feed motor & chip breaker. -- (2) 2-7/8" Dia. idler rollers in table; quick-set adjustment. -- 1/2 HP Bed elevation motor. -- eTEK "CH-525" Digital thickness controller with: LCD Display & Touchpad.Complete with: -- Instruction Manual & Parts List.NOTE: Seller purchased new and states machine has light use.