
704-841-2001
Backed with a massive machinery database considered to be “the blue book” of woodworking machinery), EX-FACTORY Auctions provides a complete assessment of your equipment and allows you to interact with the market real-time in our dynamic Online Auction!
Industry
Woodworking
1910 Results Found

704-841-2001
SELCO - HS0-128A, ...Horizontal Auto-Tie Baler -- Motor: 50 HP -- Cylinder: 8" -- Feed Opening: 36" x 28" -- Conveyor NOT included -- Loaded onto your Truck
SELCO - HL50: Horizontal Closed Door BalerSpecifications: -- Large corrugated wide-mouth Baler. -- Horizontal Closed Door. -- Max. amps: Draw 48 amp; max. motor: 39 amp. -- Max HP motor: 30 HP – 60 Hz – 3 phase. -- Bale size: 72″ x 36″ x 48″. -- Feed opening: 50″ x 46″. -- Main pump: 800 PSI. -- Hydraulic pump capacity: 54 GPM. -- Oil reservoir capacity: 180 Gal. -- Cycle time: 20 Sec. -- Ramface pressure: 68 PSI. -- Baling material weight: 1,500 – 1,800 Lbs. -- Bale volume: 72 Cu. ft. -- Main cylinder: 7″ Bore; 62″ stroke. -- Door cylinder: 4″ Bore; 12″ stroke.
Call for Price
SELCO - HL-12-LH: Horizontal Baler with Infeed Conveyor• Motor: 20 HP. • Main Cylinder: 6";.• Hopper Opening: 50"; x 28";.• Cycle Time (No Load): 15 Seconds.• System Pressure: 2,000 PSI.• Total Compression Force: 56,556 Lbs.
SEVEIN - 12KVA, operates on 50 - 60 Hz, ...Transformer with Neutral wire (on 400 V side). -- General-purpose enclosed, European made, 12 KVA, 3-Phase ventilated Autotransformer. -- Primary 400 V, Secondary 208 - 220 V, 50 - 60 Hz.
SHENG-SHING - SDM-25, ...25" Wide Belt Sander1-Head; 24" width cap.; rubber-covered contact roll; approx. 10 HP motor. -- Abrasive belt size 25" x 48" with: Air tensioning & electronic abrasive belt tracking. -- 5-1/2" Max. height opening with: Manual raise & lower; variable feed speed drive. -- Complete with: Magnetic controls & dust outlet.
SHENG-SHING - SDM-15 ...Wide Belt Sander (Open Ended)15" Single Head Wide Belt Sander with open end for up to 30 " capacity. -- Sanding Head: 15" Wide (30" cap. with 2-pass); 8" Helically Grooved Rubber Covered Contact Roll with 7.5 HP Drive. -- Features: 0" - 6" Part thickness cap., 2-speed conveyor feed 12 or 16 FPM; 16" x 48" Abrasive belts with air tensioning, pneumatic abrasive belt tracking.
MIDWEST AUTOMATION GS 214 Top and Bottom Glue Spreader53" Cap., top & bottom opposed glue applicator rolls, max. 3" opening, 40" pass-line height, 7-3/4" dia. grooved rubber spreading rolls. -- Rolls fitted with Teflon end seals and water tight bearings, upper elevator opening by single hand wheel on left with dial indicator; dual hand wheel opening glue film thickness adjustment. -- Galvanized collection tank; 54 FPM feed speed, top & bottom direct drive, 1.5 HP direct drive motors. -- Complete with: (2) Protection safety guards at roller in- & outfeed with safety interlocks, complies with UL & CE safety standards.
$10,250
Automatically feeds, shapes & ejects Rosette blocks in sizes from 2-1/2" - 5" max. square blocks; 1.5 HP motor belt drives 2-7/8" spindle cutterhead @ 7,500 RPM. -- Operation: Adjustable hopper feed to side of spindle automatically indexes Rosette blocks under cutterhead up against a corner-V holding fixture with overhead spring fingers, cutterhead advances and machines Rosette, then automatically ejects block to front (hydraulic position of block and air eject cylinder). -- Features: Cutterhead equipped for standard 16°/60° corrugated back 1/4" thick knives to be ground at 0° hook angle. -- Produces up to (500) Rosettes/Hr; Rosette profiles can be ground on any profile grinder for infinitely variable design possibilities; table top unit may include base.
$13,250
Automatically feeds, shapes & ejects Rosette blocks in sizes from 5-1/2" - 8" max. square blocks; 3 HP motor belt drives 4-3/4" spindle cutterhead @ 7,500 RPM. -- Operation: Adjustable hopper feed to side of spindle automatically indexes Rosette blocks under cutterhead up against a corner-V holding fixture with overhead spring fingers, cutterhead advances and machines Rosette, then automatically ejects block to front (hydraulic position of block and air eject cylinder). -- Features: Cutterhead equipped for standard 16°/60° corrugated back 1/4" thick knives to be ground at 0° hook angle. -- Produces up to (500) Rosettes/Hr; Rosette profiles can be ground on any profile grinder for infinitely variable design possibilities; table top unit may include base.
$32,250
Horizontal Tilting Multi-Moulder with Verical Router System designed for curved casings, crowns, circles, ellipses and straight mouldings. -- Equipped with: (1) 1-1/4" Diameter Spindle, 6" max. width x 7" max. thickness cap., 7.5 HP spindle motor, 6,000 RPM spindle with reverse rotation, 6-1/2" max. cutting circle horizontal, 6" max. cutting circle tilted, 0° - 52° horizontal tilting arbor, hand wheel spindle height & spindle tilt adjustment. -- Variable feed speed from 0 - 30 FPM, DC feed feed motor; hand wheel adjustable thickness opening, 34" x 30" table, independently adjustable feed rollers, and mechanically adjusted fence. -- 3.25 HP, 5-speed Porter Cable router with 1/2" shank included. This allows easy insert & Channels on both straight and curved mouldings. -- Designed to use standard 4" dia. 2-knife cutterhead for 16°/60° 1/4" corrugated back knives, (1) supplied; includes operating manual & video, parts list and covered by (1) year warranty. -- Optional: ProScale digital readouts for height and tilt settings, please add $900 for each, or for the Optional 8’’ spindle and aluminum Cutter-head, please add $3,550
$28,250
Designed for curved casings, crowns, circles, ellipses and straight mouldings. -- Working dimensions: 6" wide x 7" thickness capacity. -- Spindle diameter 1-1/4" with cutterhead speed of 6,000 RPM. 6-1/2" max. cutting circle in horizontal position, 6" max. cutting circle tilted. -- Feed motor 7.5 HP variable speed 0 - 30 FPM. -- Tilting of spindle head 0° - 52°. -- Includes: Hand wheel for spindle height & tilt adjustment, mechanically adjustable fence for accurate and easy positioning. Axial adjustment. Floating work table 30" x 23". -- Linear tracking system guides the work piece smoothly and directly under the cutterhead, while keeping the workpiece flat. -- Includes (1) 4" dia. corrugated cutterhead. Operating video and manual, spare parts list and (1) year warranty. -- Additional options: Proscale digital readout for height and tilt setting .... add $900.00 for each.
$10,000
MINNESOTA 24-8 Multi-Spindle Carving Machine.Specifications: -- Spindles/Capacity: (24) Spindles, 8" between centers & 72" length capacity. -- Motors: (12) 0.75 HP motors with (1) motor driving (2) spindles via flat belt. -- Features: Manual table elevation, motorized stock rotation, non-indexable head. -- Comes with: (2) Sets of carving tools (one medium and one fine). -- Includes: Tables for flat carving - to be confirmed (?).
$975
MOAK - NO. 7, ...Spindle ShaperSpecifications: -- 1.5 HP motor, belt driven to spindle; 9,000 RPM spindle speed; 1" diameter spindle. -- Length of spindle above table is 5"; 3-1/4" vertical adjustment of spindle; 22" x 42" table; manual starter; 750 Lbs machine weight.
Call for Price
MOLDOW Style, by ' NEU-JKF', Modular Baghouse with chain-sweep bottom feeding into a Rotary Air Lock (RAL) at the end of filter bank. -- General Data: Approx 35,600 CFM running at a 5:1 Air-to-Cloth Ratio. Total of 7,125 sq. ft. of filter area comprised of (14) modules each containing (27) filter bags. Filter bags are 8.5" dia. by approx. 96" long. All modules including inlets are fitted with filter bags. -- Main fans: Total of (3) Material Handling (MH)fans. (2) NORTHERN BLOWER Size 23, Des 5691, CL 3 Fans each belt driven by 60 HP TEFC motor. Fan inlets supplied by 26" dia. pipes. (1) type JK 25 HP MH blower. -- Filter Cleaning: Each module is supplied with a 2 HP approx. regenerative high pressure fans to sequentially back-flush the dust from the bags during operation and thereby falling into the continuous hopper with a drag-chain-sweep mechanism that rides along the bottom of hopper and feeds into the RAL. -- Return Air: All modules are ducted into one return air manifold pipe. -- Electrical Controls: CONQUEST free standing electrical control panel with visual light indicators for monitoring system status. Panel contains all start/stop pushbuttons and selector switches, and main disconnect. -- Includes: Steel Support frame with a walkway to the access doors which can act as explosion vents. Full set of polyester filter bags. -- Inquire for a cost for professional dismantling and transportation.
Call for Price
MOLDOW 184 MXN-324 Expandable Baghouse - 18 Total Modules with (4) Inlet Sections. Specifications. -- 72,000 CFM modular/expandable unit, currently with (14) Filter sections @ 5,000 CFM per section (24 bags per section). -- Approx 336 filter (8.6" dia. by 120" long) , 9,300 sq. ft. of total filter media, 7.75:1 air to cloth ratio Shell is under negative pressure allowing a high efficiency clean air fan.. -- Main Fan: Air Handling IAP A600 SWSI, Class IV, S/N 26862-1 rated at 90,000 CFM @ 1321 RPM, 16.0/20.3" SP & 290/308 BHP. Fan is A - Airfoil type wheel & is non-overloading powered by MARATHON "445Ta" belt driven TEFC 300 HP motor.. Currently fan inlet is connected with a 30" pipe. Regenerative Filter Cleaning: -- Each row of filter bags is cleaned continuously during operation by use of a regeneration carriage/trolley rides along top of filter bank) with a 4 KW (5.3 HP) high-pressure fan that sends air from the clean-air chamber back through the filter bags using nozzle pipes.Bags are fitted with an inner spring bracing. Special bag design reduces air velocity which increases air and dust loading considerably. -- Equipped with: Built-in bottom drag link chain which brings dust to one end where it is discharged through approx. 9" x 30" Rotary Air Lock (RAL). Currently a transfer fan moves dust to storage bin.. Summer/Winter Diverter/Abort Gate connected on outlet/return air line.Comes with: -- Relay Fan, IAP 911 RBO, to pneumatically convey collected dust at discharge of RAL. -- Platform with safety railings and ladder to access regeneration cabinet (return air plenum). -- Interior electrical control panel, support frame, and exterior ductwork. Single heavy sheet metal flanged rectangular return air pipe. Overall Dimensions: -- 45' Long by 12'-9" wide by 28.5' high (5.5' hopper to ground, 8' high hopper and 15' top section). -- Professional dismantling, rigging, transport and installation is available upon request.
Call for Price
MORBIDELLI UNIFLEX HP 1.1 CNC MACHINING CENTER (2-HEAD): -- Specifications:Flexible "TOP & BOTTOM" Machining Center that uses an innovative panel handling system. -- Positioning SpeedsThe "UNIFLEX" can reach positioning speeds of: 130 MPM in "X" Axis; 80 MPM in "Y" axis; 50 MPM in "Z" axis with total safety, providing an unmatched working capacity. -- Working DimensionsMax. worktable part size for: "X" axis is 118" (3,000 mm); "Y" axis is 51" (1,300 mm) "Z" axis max. part thickness 3.1" (80 mm).Min. worktable part size for: "X" Axis is 7.8" (200 mm); "Y" axis 2.7" (70 mm); min. part thickness 0.157" (4 mm). -- Worktable:Automatic LH infeed air table with gripper clamps; automatic RH outfeed transfer conveyor with belts; both infeed & outfeed are considered Robot ready. -- Boring Units:(1) Top mounted boring block: 4.2 HP (3 kW); variable speed from 1,500 - 6,000 RPM; (48) vertical spindles: 24-Spindles in "X axis & 24-spindles in "Y" axis; (6) horizontal spindles with: (2+2) in "X" axis & (1+1) in "Y" axis; (1) 4.2 HP (3 kW) - 9,000 RPM, NC controlled 0°-90° "X/Y" Grooving Saw, max. 120 mm dia. blade.(1) Bottom mounted boring block: 4.2 HP (3 kW); variable speed from 1,500 - 6,000 RPM; (48) vertical spindles: 24-Spindles in "X axis & 24-spindles in "Y" axis; (6) horizontal spindles with: (2 + 2) in "X" axis & (1 + 1) in "Y" axis; (1) 4.2 HP (3 kW) - 9,000 RPM, NC controlled 0°-90° "X/Y" Grooving Saw, max. 120 mm dia. blade. -- Machining:(1) Top mounted 10 HP (7.5 kW) electro-spindle with: HSK D-50 Adaptor; "ERC 32" tool holders & RC-32 collets, 1,500 - 24,000 RPM.(1) Bottom mounted 10 HP (7.5 kW) electro-spindle HSK D-50 adaptors, "ERC 32" tool holders & RC-32 collets; 1,500 - 24,000 RPM. -- Operator Interface:PC Front-End with: "XYLOG PLUS" + Windows environment Operating system; 20 GB hard drive; 17" TFT monitor; international keyboard, soft touch keypad & industrial mouse; RS-232 Serial ports, USB ports; (1) 1.44 MB floppy drive; (1) CD ROM drive; all mounted in separate control console. -- Operating System:"XYLOG PLUS" Offers Real time multitask processing; programs can be transferred via diskette or downloaded by wire. -- Complete with: Pneumatic part clamping devices; sound enclosure; safety mats. -- Operating features: Machine can work the panel from above & below at the same time and can produce (2) identical or mirrored panels per cycle with no difficulty.The "UNIFLEX" can machine porous materials since the pieces are held with grippers, directly managed by the numerical control; it can even process small pieces and carry out "through" machining.(4) Operating modes at each cycle, it can change automatically from: Top machining to bottom machining, to top & bottom machining together, either on (1 or 2) stacked panels. -- Actual model is MORBIDELLI UNIFLEX HP.
MORBIDELLI AUTHOR M400 FR FLAT TABLE MACHINE(W/LOADING/RAKE/OFFLOADING): -- Specifications:5' x 12' Stationary extruded aluminum "MATRIX" table for "Nested Base" manufacturing with "Rake" and "Automatic Off-Loading Conveyor".Loading/working/processing direction is from LH (facing to RH (facing). -- Work Area:"X" Axis 143.7" (3,650 mm), "Y" axis 62.9" (1,600 mm), "Z" axis stroke 11" (280 mm), max material thickness is 6.69" (170 mm). -- Positioning Speeds:"X" & "Y" Axis 279 FPM (85 MPM), "Z" axis 98 FPM (30 MPM).Closed loop AC servo drive system with Precision Rack/Pinion in "X" axis & recirculating ground ball screw in the "Y" & "Z" axis.All axes ride on precision prism linear guideways. -- Work Table:5' x 12' Aluminum grid "MATRIX" vacuum table machined with a square grid pattern for fixturing parts, grid pattern allows use of vacuum pods or closed cell rope gasket material and use of spoil boards.(9) Independent, NC controlled working zone areas; external pop-up reference pins located on the sides & back of the table for positioning parts. -- Boring Unit "F37L2":3 HP (2.2 kW) - variable speed up to 7,000 RPM motor; F37L2 Boring Block with (24) Vertical spindles with (10) independent vertical spindles in "X" axis & (14) spindles in "Y" axis.The 10-spindle "X" axis boring unit is NC controlled with a 11.5" (293 mm) "Y" adjustable spread from its home position & independently controlled according to the drilling pattern being performed, this feature is IDEAL for high-speed line hole drilling.(12) Horizontal spindles with (4+4) in "X" axis on the programmable Independently NC controlled 10-spindle vertical boring unit, & (2+2) on the 14-spindle boring unit in "Y" axis. (1) NC controlled 0° - 90° "X" / "Y" Grooving Saw for max. 120 mm dia. blade. -- Machining:(1) 16.5 HP (12 kW) "Power 2000" Electro spindle w/lifetime lubrication and HSK F63 adaptor, NC controlled spindle speeds from 900 - 18,000 RPM.(1) 16-position "Rapid-16 traveling ATC tool plate for "on the fly" ATC NC Touch-off Probe for automatic Tool Length setting. -- Operator & Machine Control,PC Front End with XILOG PLUS + Windows "7" operating system. 17" high resolution LCD flat screen; ergonomic keypad.USB Ports, serial ports RS-232 & RS-242 & Ethernet adaptor.Programs can be transferred via USB or downloading by wire is possible; all computer components are mounted on a mobile stand. -- "XILOG Plus" offers incredible list of functions from: (a) Auto-diagnostic to (z) zooming; controlled acceleration & deceleration; encoder feedback; dynamic tool correction via PLC due to active tool wear using space-and-time criteria. -- Additionally equipped with: Onboard mini-CAD with built-in programming for writing circles, ellipses, & angles with only a few keystrokes.Onboard cycle optimization; onboard calculator; mirror-imaging and repeat imaging; all electronics mounted in an air conditioned, dust-free environment control cabinet. -- Complete with:(3) 300 m³/Hr "BECKER" Vacuum pumps;
$89,500
MORBIDELLI N 100 15 FLAT TABLE MACHINE (W/ATC/BORING/RAKE): -- Specifications: 5' x 12' x 37" H High-efficiency laminate aluminum with Magnetic vacuum locking system.Grid pattern allows use of vacuum pods or closed cell rope gasket material & use of spoil boards for nested base machining, Part location pop-up pins mounted on table perimeter, Chips conveying device. -- Working Area: X-Axis 3,686 mm (145.12"), Y-Axis 1,555 mm (61.22"), Z- Axis 150 mm (5.91"). -- Travels:X-Axis 4,230 mm (166.54), Y-Axis 1,985 mm (78.15"), Z-Axis 250 mm (9.84"). -- Positioning Speeds: X- & Y- Axes 35 MPM (114 FPM), Moving Gantry, High precision rack & pinion system for X & Y Axes, Ground ball screws for Z-Axis, All axes ride on extra-large precision profile linear guide ways. -- Boring Unit: 2.2 kW (3 HP) Motor, (12) Independent vertical roto-axial spindles with (8) in X-Axis & (4) in Y-Axis, Maximum spindle speed 8,000 RPM. -- Machining: (1) 15 kW (21 HP) Air-cooled electro spindle with HSK F63 Adaptor, Variable spindle speeds to 24,000 RPM, (1) 14-Position TR side tool changer. -- Operator Interface:Mobile console with Integrated PC “EYE-M"; Industrial PC with 21-1/2" Full HD Multi-touch color touchscreen, WINDOWS Operating system, "MAESTRO SUITE" with Auto-diagnostic to Zooming, Controlled acceleration & deceleration, Encoder feedback, Dynamic tool correction via PLC due to active tool wear using space-and-time criteria, "TECPAD" Remote pendant with 7" Color touchscreen. -- Complete with: PRO-SPACE safety system which allows worktable access to all sides of the machine, (1) 300 m³/Hr. Vacuum pump, Automatic lube system, -- NOTE: Machine was de-installed by a technician and is currently in storage.
MORBIDELLI AUTHOR 503 FT CUSTOM CNC MACHINING CENTER (W/ATC): -- Specifications:4' x 8' Custom Stationary Extruded Aluminum Table for "Nested Base" manufacturing;Working cap. "X" axis is 125.2" (3,180 mm), "Y" axis is 41.3" (1,050 mm) for routing "Z" axis stroke is 5.7" (144 mm); max. material thickness is 3.1" (80 mm) -- Positioning speed:"X " & "Y" axis is 213 FPM. (65 MPM), "Z" axis is 82 FPM (25 MPM). -- Work Table: 4' x 8' Custom Stationary Extruded Aluminum Table for "Nested Base" manufacturing;(2) pneumatic side stops, (2) working areas -- Machining Units:(1) 10 HP (7.5 kW) Vertically mounted electro-spindle router with ISO-30 adapter, LH & RH rotation, inverter driven from 12,000 - 18,000 RPM,(1) 5-position ATC tool rack mounted on the LH side for automatic tool change, -- Operator & Machine Control:Separate control cabinet with Morbidelli "TRIA 7500" CNC Multi-processor, VGA monitor, ergonomic keypad, 3-1/2" disk drive, and (2) serial ports RS-232 & RS-242.Offers incredible list of functions from (a) auto-diagnostic to (z) zooming; -- Complete with: Voltage stabilizer 208. 230, 460 V, 60 Hz, 3 Phase Auto Transformer (1) 100 m³/Hr vacuum pump. -- Actual model is MORBIDELLI AUTHOR 503 FT CUSTOM
Call for Price
PRO-EDGE TECHNOLOGY SQUEEZETIGHT CASE CLAMP (AUTOMATIC FEED THROUGH): -- Specifications:The SqueezeTight automatic hydraulic case clamp does the work for you. The vertical pressing system with motors & independently controlled crossbars move according to the size of the piece to be pressed, mobile parts slide along linear bearings and guides. -- Operating Cycle;Once the piece of furniture is assembled on the preparation bench the operator starts the automatic cycle and the carcass enters the machine.The reading devices automatically determine the length and height of the workpiece and send this information to the PLC which positions the mobile head and the conveyor and stops the carcass in position. The beam automatically moves to the preset position.Each of the mobile heads are fitted with: (2) RH & (2) LH Horizontal pressure beams + (4) stationary & (1) adjustable top pressure clamps.The Clamping Cycle is 100% programmable & pressing is by a 10 HP (7.5 kW) Hydraulic pump system.The in-out-cross transfer powered belt conveyors are driven by "SIEMENS" AC brushless motors. -- Working Capacity:9.8" - 89.7" (250 - 2,280 mm) working width/length, 9.8" - 42.9" (250 - 1,090 mm) working height, 9.8" - 25.9" (250 - 660 mm) working depth. -- Positioning Speed:32.8 - 131.3 FPM (10 - 40 MPM) Variable speed controlled by programmable inverter. -- The carcass transfer system is located at the bottom of the bed and consists of an electro-welded steel structure on which a closed loop belt is driven by an inverter-controlled "SIEMENS" motor. -- Operator Interface:Automatic cycle control from onboard "HMI" Touch Screen control + "DELTA" VFD's & PLC with adjustment for all clamping aspects. Clamping pressure strength up to 1,200 PSI over-all. -- Complete with:(1) 98" Long powered in-feed conveyor belt with alignment guideways, (1) 98" Long powered cross-feed conveyor belt with alignment guideways & (1) 98" Long powered out-feed conveyor belt. Parameter Safety Light Curtain System. -- NOT included:Cost for Delivery, installation, and training (please call for quotes). -- Actual Model is PRO-EDGE TECHNOLOGY SQUEEZETIGHT