EX-FACTORY INC.
EX-FACTORY INC.
 704-841-2001

Backed with a massive machinery database considered to be “the blue book” of woodworking machinery), EX-FACTORY Auctions provides a complete assessment of your equipment and allows you to interact with the market real-time in our dynamic Online Auction!

Filtering

Reset All 

thru
 Used     New
Viewing Page 88 of 96
1910 Results Found
Sort By 
EX-FACTORY-INC
 704-841-2001
2007 Heesemann KSA 8 CSD  Finishing-Wood
$1,500

--AT AUCTION-- HEESEMANN KSA 8 CSD 80" Lacquer/Sealer Sander This is a Very Special "extra wide" HEESEMANN equipped with: HEESEMANN's patented "CSD" selective pressure adjustment system, sensors placed every 5/8" (16 mm) sense part configuration; pressure for each segment can be preprogrammed to provide less pressure on the outer edges, or more in the center if desired. The "CSD" computer control will hold a max. of (20) programs. Equipped with: Segmented Polishing Platen: Segments are computer controlled to conform to irregular shaped panels; sanding pressure on panel edges is adjustable. Platen will accept panel thickness variation up to 5/64" (2 mm). Dual speed motor: 26 & 31 kW (35 & 42 HP); abrasive belt speed: 10 + 20 MPS (33 + 66 FPM); abrasive belt size: 2,050 mm x 3,250 mm (80.7" x 128"); pneumatic air tension and tracking control. 250 mm Dia. Rotary Panel Cleaning Brush, 5 HP motor, 150 mm Outfeed Rotary Panel Cleaning Brush, and 2 HP motor. Additional Features: Vacuum bed assembly to ensure flatness of parts and feeding of small parts. Computer control and monitor, light indication of panel movement; electronic abrasive belt tracking. Feed System: Variable feed speed from 5 - 15 MPM (16 - 49 FPM); 4 kW (5 HP) feed motor; motorized thickness opening. NOTE: This Sander had a "Brand New" ...$ 17,000 display/control installed shortly before it was taken out of service in 2016. The machine has been in storage since that time.

 Zeeland, MI
 704-841-2001

 Call
2004 Heesemann LSM 8  Sander
$90,000

HEESEMANN - LSM 8-5 RRRL, ...53" Wide Belt Sander53" Width cap.: Drum, Drum, Drum, and CSD® Pad.Head Configuration:• Unit 1 - Longitudinal Sanding Unit: Steel contact roller, helically grooved. - Single-speed 48 HP motor, electronic braking.• Unit 2 - Longitudinal Sanding Unit: Rubber-covered contact roller, helically grooved. - Single-speed 35 HP motor, electronic braking.• Unit 3 - Longitudinal Sanding Unit:- Rubber-covered contact roller, helically grooved. - Single-speed 35 HP motor, electronic braking, bi-directional drive.• Unit 4 - Longitudinal Sanding Unit: CSD® Segmented pad system, 2-speed 20/26 HP motor, electronic braking.• Unit 5 - Panel Cleaning Brush: Fiber trimming, 2.3 HP Motor.Specifications: -- Working height: 880 mm (34.64"). -- Workpiece thickness: 3 mm to 150 mm (1/8" to 6"). -- Working width: 1,300 mm (51-1/8"). -- Longitudinal belt: 1,350 x 2,620 mm (53" x 103"). -- Machine voltage: U.S. Electrics 480 Volts, 3-Phase, 60 cycles.Constant Pass LineController: -- Industrial PC. -- TFT Color touchscreen. -- Windows® Operating System. -- (100) Memory addresses for: • CSD® sanding pressure. • Sanding start/stop. • Sanding belt speeds. • Grit sequence indication. • Sanding belt selection - "ON/OFF". • 1-Button sequenced starting for all motors.RS-232 Serial port.RJ-45 LAN Port.Modem with software licenses.For All additional, detailed specs, select the "View Literature" link .

 704-841-2001

 Call
2005 Heesemann LSM 8/3  Sander
$55,000

HEESEMANN LSM-8/3-OSR Wide Belt Finishing Sander, 52" and (3) Heads; Equipped with: (1) longitudinal segmented platen head. and (2) Orbital Platens -- 1st Head: Longitudinal segmented platen head. Segmented Polishing Platen, 20 & 27 HP dual speed motor. electronically controlled segments to conform to panel size,.2620 x 1350 mm (91.4 x 53.2") Sanding belt. - Equipped with HEESEMANN's patented "CSD" selective pressure adjustment system, sensors placed every 16 mm (5/8") sense part configuration; pressure for each segment, to eliminate sand through, can be pre-programmed to provide less pressure on the outer edges or more in the center if desired. The "CSD" computer control will hold a maximum of (20) programs. -- 2nd & 3rd Heads: OSR Dual orbital action head with (1) high-speed orbit on sanding pad, powered by 3 kW (4.5 HP) motor.Secondary oscillation movement of platens powered by 1.5 HP motor. Upstream and downstream vacuum chutes on each head for dust localized dust pickup.- Platens feature "quick change" abrasive material; Both orbital heads with variable speed inverter drives. -- Outfeed Rotary Brush with cleaning brush loading with single end adjustment , 6" max. dia., 3.4 HP motor. -- Variable feed speed from 13 to 82 FPM, 6.5 HP feed drive. -- Infeed and outfeed Ssissor Lift and Control box shown are not included. -- Motorized thickness opening 1/4" to 3-5/32" max. - -- Power Consumption: 63 KW, 75 Amps. -- Separate display console for CSD control.

 704-841-2001

 Call
2008 Heesemann LSM 8  Sander
$87,750

HEESEMANN - LSM 8, ...3-Head Wide Belt Sander53" Width cap. Crossbelt, Combination , and DrumHead Configuration:1st Head: Cross Belt Sanding Unit, 2-speed motor - 19/24 kW (26/33 HP). - Abrasive belt speed: 12/24 MPS (39/78 FPS); Cross Belt (Cloth), 4,800 x 150 mm (189" x 6").2nd Head: Combination Longitudinal Sanding Unit Front retractable roller for light calibrating and segmented pad system for fine sanding; bi-directional sanding; Door-in-Door viewing; 2 speed motor - 31/37 Hp, abrasive belt speed 10/20 mps (33/65 fps3rd Head: Longitudinal Sanding Unit Internal pressure segment belt for finer sanding Inner chevron belt; Inverter driven motor: 26 kW (34 HP); abrasive belt speed: 0.5-16 MPS (1.6-52 FPS); Longitudinal Belt: 2,620 x 1,350 mm (103" x 53").Unit 4: Panel Cleaning Brush, Fiber trimming.Specifications: -- HEESEMANN's LSM-8 Sanders are designed for heavy (2 - 3) shift operations; this Sander is ideal for: Whitewood sanding of veneered panels and panels coated with various sealers. -- The crossbelt removes tape, cuts short fibers that contribute to grain rising, and sands panels with "book-matched" veneer. -- The last sanding unit is equipped with an internal pressure segment belt for an extra smooth finish.Enhanced 16 mm control roller spacing with (3) rollers per segmented pad. -- CSD® Segmented pad system is equipped on all (3) sanding units. -- Pneumatic conveyor belt cleaning. -- Infeed extension with non-driven rollers. --Electronic variable feed speed from 5 - 25 MPM (16-82 FPM). --Workpiece thickness 3 mm - 140 mm (1/8" to 5-1/2").Equipped with & Features: -- Vacuum Table: Only HEESEMANN builds it into the frame for superior holddown! -- Industrial PC controller, Windows® Operating System.Width Capacity: 53"

 704-841-2001

 Call
2021 Heesemann HSM.2 DB-S 2  Finishing-Wood
$120,000

Heesemann HSM Features:Thickness adjustment of sanding heads from 3 to 160 mm (0.118 to 6.3") -- Constant working height of 880 mm (34.6") -- A constant pass line features 3 mm per second adjustment -- An over-thickness control system -- Emergency stops located at machine infeed and outfeed -- Integrated switch cabinet -- Control for excessive workpiece heightHeesemann's HSM transport conveyor features:Electronic variable speed infeed conveyor drive -- Controllable feed speed by an industrial PC -- A transport belt with ½" diamond profiles and one-piece construction -- Automatic tensioning & trackingPress-on RollerA 50 mm roller at the infeed of the machine to hold down thin and warped workpieces with thefollowing features:Spring loaded and adjustable -- Includes workpiece over-thickness controlHigh Performance Vacuum Hold DownEquipped with a high-performance vacuum hold down system for safe movement of workpiecesshorter than 500 mm (20") in feed direction including integrated ventilator in machine base. Canbe turned on or off via controller or in individual programs. The vacuum blower is a high pressureblower, offering optimal performance with minimal power requirements due to the fandesign, helping provide excellent suction with low power consumption.Emergency StopIndustrial PC, This sander is equipped with a 15" high resolution touch screen / industrial PC and features:High resolution display -- Windows® embedded operating system -- Pendent mounted with adjustable viewing position -- Ethernet connection -- Configured as web address for easy network access -- Automatic on-screen diagnostics -- Metric or English input -- 1000 memory addresses -- Alpha/numeric format -- Password protected -- Digital keypad input -- Workpiece thickness -- Conveyor belt feed speed -- Sanding pressures -- One button startRoller Table For infeed500mm long (20";) -- Height adjustableHead 1: DB-S Head – Rotating Planetary Sanding Unit:10 driven discs with quick changing device -- Rotation in both directions -- Central height adjustment -- 7.5 kW (10 Hp) motor to power the discs -- 1.5 kW (2 Hp) motor gear box -- Brush trimming: Flex Trim -- Tool Diameter: 150 mm (6";) -- Other brush discs available on demand -- One set of discs is included with sanding headHead 2: DB-S Head – Rotating Planetary Sanding Unit:10 driven discs with quick changing device -- Rotation in both directions -- Central height adjustment -- 7.5 kW (10 Hp) motor to power the discs -- 1.5 kW (2 Hp) motor gear box -- Brush trimming: Flex Trim -- Tool Diameter: 150 mm (6";) -- Other brush discs available on demand -- One set of discs is included with sanding head Brush trimming: Flex Trim -- Tool Diameter: 150 mm (6";) -- Other brush discs available on demand -- One set of discs is included with sanding headTechnical Specifications:Working height: 880 mm (36.2") --Workpiece thickness: 3 mm to 160 mm (0.118" to 6.29") --Working width: 1300 mm (51.2") --Transport belt speed: 3 mpm

 704-841-2001

 Call
2007 Heesemann KSA 8  Finishing-Wood
$29,900

HEESEMANN - KSA 8 CSD, ...Lacquer/Sealer Sander w/80" Belt WidthThis is a Very Special "extra wide" HEESEMANN equipped with: HEESEMANN's patented "CSD" selective pressure adjustment system, sensors placed every 5/8" (16 mm) sense part configuration; pressure for each segment can be preprogrammed to provide less pressure on the outer edges, or more in the center if desired. The "CSD" computer control will hold a max. of (20) programs.Equipped with: -- Segmented Polishing Platen: Segments are computer controlled to conform to irregular shaped panels; sanding pressure on panel edges is adjustable. -- Platen will accept panel thickness variation up to 5/64" (2 mm). -- Dual speed motor: 26 & 31 kW (35 & 42 HP); abrasive belt speed: 10 + 20 MPS (33 + 66 FPM); abrasive belt size: 2,050 mm x 3,250 mm (80.7" x 128"); pneumatic air tension and tracking control. -- 250 mm Dia. Rotary Panel Cleaning Brush, 5 HP motor, 150 mm Outfeed Rotary Panel Cleaning Brush, and 2 HP motor.Additional Features: -- Vacuum bed assembly to ensure flatness of parts and feeding of small parts. -- Computer control and monitor, light indication of panel movement; electronic abrasive belt tracking.Feed System: -- Variable feed speed from 5 - 15 MPM (16 - 49 FPM); 4 kW (5 HP) feed motor; motorized thickness opening.NOTE: This Sander had a "Brand New" ...$ 17,000 display/control installed shortly before it was taken out of service in 2016. The machine has been in storage since that time.

 704-841-2001

 Call
2001 Heian FP-151-MC-2113  Router
$39,700

HEIAN FP-151-MC-2113 5-Axis CNC MachineFor high speed & precision routing/trimming & sizing wood and composite parts.Equipped With: -- (2100 mm) x (1,300 mm), moving table, fixed bridge style machining center; mahogany vacuum table. -- 3.7 kW, NT 30 Type ATC spindle, variable speed from 2,000 - 18,000 RPM with 8-position tool carousel. -- FANUC "16i CNC Control, 10.4" LCD , RS-232C/PCMCIA (memory card). Features: -- 5-Axis simultaneous motion, M & G code programming, inch or metric operation. -- Working Axes Stroke & Speed: X-Axis (2,600 mm) 60 m/Min; Y-axis (1,600 mm) 40 m/Mn; Z-axis (800 mm) 20 m/Min -- C-axis +/- 270°; B-axis +/- 110°; C-axis travels at 4,000°/Min and B travels at 4,000°/Min. -- Complete with assorted tool holders.

 704-841-2001

 Call
HMC 2-SAW  Trim Saw
$32,500

HMC 2-Saw Trimmer Model ET-10,;Complete with the following features: --16′ capacity. --Push Button Setworks. --Left hand (feeds from left to right). --Cuts up to 8″ thick. --Belt Conveyor for waste.NOTE: Removed from service and it was running just fine at the time of removal. Stored outside.

 704-841-2001

 Call
Hofer HOP 160 K  Glue Equipment
Call for Price

HOFER HOP 160 K Hydraulic Door/Veneer Heavy Duty Cold PressSpecifications:Platen size 63" deep x 98" long, Total Daylight/Opening 32".available. Currently set at about 13" opening. Top platen is hydraulically powered by a 2.2 KW power pack. and has (10 sets) of bolt holes for manual adjustment of daylight opening.Equipped with:(8) 3-1/4" Diameter Hydraulic cylinders, Rack & pinion platen leveling adjustment.Front and back loading (access on all sides).Heavy duty steel structural beams. Bolted top and bottom platens.Features:Pneumatically loaded 3 +1 rows of idle rollers on bottom platen for ease of feeding the load in and out front of press. Air valve for up/down selection of bottom platen rollers.Hydraulic closing speed adjustment.Electrical controls on right hand side.Dimensions/Weight: 124" x 72" x 122" H. Approx. 12,000 Lbs.

 704-841-2001

 Call
1986 Hofer STANDARD  Clamp Carrier
Call for Price

HOFER - STANDARD KPD: Case Clamp (Semi Automatic) -- SpecificationsWorking Capacity: 98" x 55" High x 27" wide/deep clamping cap.; 12" x 12" x 27" min. clamping cap. -- FeaturesMotorized horizontal & vertical pressure walls move simultaneously or individually on precision ball screws at 60 IPM clamping and 120 IPM traveling into position; each with 1-1/2 HP drive motor. -- Vertical & horizontal interlocking pressure walls; each with: (7) Individual beams that move parallel & square to the clamp frame's sidewall; "Joystick" for 8-way function control. -- 5,500 Lbs Max. pressure per pressure beam; adjustable pressure sensor stops beam at preset pressure; infinitely variable pressure setting; timer opens Clamp automatically. -- Actual model is: HOFER STANDARD KPD.

 704-841-2001

 Call
2002 Hoffmann  Router
Call for Price

HOFFMANN PU 2 DOVETAIL ROUTER (SINGLE SPINDLE) Pneumatic Dovetail Routing Machine - Dovetail routing machine for use with HOFFMAN dovetail butterfly connectors. - Maximum routing height 4", Max. workpiece height 5-3/4" - Table size 15-1/2” x 27-1/2” x 36-1/2” H - Production speed: Approx. 16 SPM (2 Complete rectangular frames) - (1) HOFFMANN "UAD 33 F" 33,000 RPM 1,000 W Router motor - 45° Fence, Accurately positions material with guide in table keyway, Quick adjustments made by adjusting fence plate - Pneumatic hold-down, Pneumatic foot pedal Includes: - Extra HOFFMANN "UAD 33 F" 33,000 RPM 1000 W Router Motor - 2007 HOFFMANN "FM1000" 35,000 RPM 1,000 W Router Motor - (2) 16” x 48” x 35” H Left-Hand & Right-Hand Aluminum Frame Tables, with 3/4” Thick Top, & 2” x 2” Aluminum frame - Palletized Dimensions: 42” x 42” x 60” H

 Haverhill, MA
 704-841-2001

 Call
Holytek HK-610  Planer
$32,500

HOLYTEK HK 610 Double Sided Planer with THOMAS MANUFACTURING Return ConveyorHOLYTEK HK 610 Double Sided Planer specifications - -- 24" x 8" Cap. Double Surface Planer, spiral carbide cutterheads belt driven by 20 HP top and 15 HP bottom motors at 4,000 RPM. -- Spriral cutter head 125 mm diam. with 96 inserts 30mm X 12 mm X 1.5 mm -- Variable feed motor delivers a range of 7 M./min to 20 M./min. (19.5 FPM to 82 FPM) -- Feed motor 3 HP, corrugated sectional infeed rollers and (4) table rollers provide superior feeding regardless of the type of wood being processed; hard-chromed table surface precision ground to provide smooth performance and maximum wear resistance at high speeds. -- Machines are currently wired for 220 Voltage.Technical Specifications:• Maximum width 610 mm (24")• Minimum length: 300 mm (11.9")• Maximum thickness 170 mm (6.69")• Minimum thickness 8 mm (.31")• Table size: 686 mm X 2616 mm (27" X 103")• Dovetailed slideways on the table elevation ensures stability and rigidity; a mechanical readout provides accurate details of table positioning adjustment; thickness limit guard is provided at the infeed end as a safety feature. • Machine Dimensions - 109" Long x 46" Wide x 68" High, Machine weight 7,280 lbsTHOMAS MANUFACTURING Return Conveyor specifications -37" Wide x 144" Long Receiving Table that transfers to a 20" Wide x 240" Long Return Conveyor1 HP - 3 Phase Variable-Speed DrivePhotoelectric SensorRemote ControlSolid State TimerSwing-Out Section that is 20" Wide x 90" Long

 704-841-2001

 Call
2000 Holytek 37DA  Sander
$14,800

Holytek 37DA Wide Belt Sander (2) Heads37" Width cap Drum, Combination Head1st Head: 7" Dia. spiral grooved rubber covered contact roller, 20 HP motor;2nd Head: Combination sanding head with 5" dia. spiral grooved rubber covered contact roll & 2" wide polishing platen, 15 HP motor.Specifications -- Abrasive belt size of 37" x 60" -- Pneumatic belt tensioning and electronic abrasive belt tracking -- 12" min. working length. -- 2 HP Conveyor belt motor, -- Variable feed speed from 13 - 52 FPM,Equipped with & Features -- Infeed & outfeed rubber covered holddown rolls; -- 0" - 4" motorized thickness adjustment by 0.5 HP motor. -- Safety stop bar, emergency rail stop across the front of conveyor -- Motor load meters.

 704-841-2001

 Call
2010 Holytek HRS-12TK  Straight Line Rip
$11,500

HOLYTEK - HRS-12TK, ...Straight Line Rip SawSpecifications: -- Overhead saw arbor, 15 HP motor belt driven, 4,500 RPM arbor. -- 12" Dia. max. saw blade. -- 3-3/8" Max. depth of cut. -- 18" Max. throat depth. -- 2 HP Stepped feed speeds of 50 - 65 - 83 - 100. -- Automatic lubrication of chain. -- Magnetic controls. -- Saw is glue line rated.Equipped with & Features: -- Overhead holddown rolls. -- Double-row of antikickback fingers. -- (6) Pressure rollers. -- Infeed adjustable fence line. -- Cast Iron table with rip fence.

 704-841-2001

 Call
2003 Holytek 920RK  Sander
$8,500

HOLYTEK GES 920 RK Wide Belt Sander(2) Heads drum and combination head -- (2) Head, 36" width cap., -- 1st Head: Heavy duty rubber covered contact drum, 15 HP motor; -- 2nd Head: Combination head with 6" dia. contact roll, 20 HP motor, -- 2 HP feed motor, 16 - 55 FPM variable feed speed, -- 37" x 75" abrasive belts, electronic oscillating belt system. -- Motorized table elevation with .25 HP motor, maximum height 125 mm (4.9")Equipped with: -- Digital read-out & infeed and outfeed spring loaded hold down rolls.

 704-841-2001

 Call
2015 Holytek HP-11  Resaw-Band
$16,800

HOLYTEK HP-11P Horizontal Resaw -- Hydraulic Feeding conveyor, hydraulic pump with 3 HP motor -- Main saw motor 20 hp. Specifications: -- Working width capacity 12“ (300 mm) -- Variable Feed Speed 0- 17 m/min (0 to 55 FPM) -- Thickness capacity 4mm to 125 mm (.11/8" to 4.92") -- Conveyor tilting 0 ° to 7° -- Electroni display of cutting height -- Blade Capacity 4270 X 25 X 0.89 mm. -- Wheels Diameter 725 mm -- Return conveyor on machine top

 704-841-2001

 Call
2000 Holytek HK-610  Planer
$21,500

HOLYTEK HK 610 Double-Sided Strato Planer -- 24" x 8" Cap. Double Surface Planer, spiral carbide cutterheads belt driven by 20 HP top and 15 HP bottom motors at 5,000 RPM. -- Spriral cutter head 125 mm diam. with 96 inserts 30 mm X 12 mm X 1.5 mm -- Variable feed motor delivers a range of 6 M./min to 25 M./min. (9.5 FPM to 82 FPM), -- Feed motor 3 HP, corrugated sectional infeed rollers and (4) table rollers provide superior feeding regardless of the type of wood being processed; -- Hard-chromed table surface precision ground to provide smooth performance and maximum wear resistance at high speeds.Technical Specifications:• Maximum width 635 mm (25")• Minimum length: 300 mm (11.9")• Maximum thickness 200 mm (7.87")• Minimum thickness 10 mm (.39")• Table size: 686 mm x 2616 mm (27" x 103")Features: &#9679 Dovetailed slideways on the table elevation ensure stability and rigidity; Mechanical readout provides accurate details of table positioning adjustment; &#9679 Thickness limit guard is provided at the infeed end as a safety feature. &#9679 Machine weight 6,600 Lbs

 704-841-2001

 Call
2007 Holytek KL-36PC  Sander
$28,900

HOLYTEK - KL-36PC, ...2-Head Sander 2-Head Planer Sander 36" with planer head & combination head.Description: -- Planing Head (P): 6'' Dia. made of steel with spiral design for heavy stock removal. 228 TCT Tips: 15 x 15 x 2.5 mm; each disposed on (6) rows. Each knife has: (4) Usable cutting edges; easy access to planing head for tips rotation or replacement. -- Precise dial indicator showing the exact positioning of the sanding pad; quiet & smooth oscillation! Pneumatic oscillation system controlled electronically by an infrared system, which is not affected by dust. -- Combination Head: (1) Drum & (1) sanding pad (C) for superior quality of finishing. Sanding belt with: 120 or 150 Grit; allows finishing sanding in a single pass. -- Elevation Table: (4) Screws. -- Infeed roller table extension: 15-3/4". -- Outfeed roller table: 15-3/4" with (2) Rollers. -- Centralized Control Panel with: Electronic digital readout (Metric or Imperial) for elevation; precise positioning at the elevation requested. -- Ammeter indicating: Electrical intensity on the spiral cutterhead and the combination head motors. -- Electrical box with: CSA Approved electrical components ensuring maximum dependability and an outstanding long-lasting performance.Specifications -- Spiral cutterhead motor: 20 HP - 600 V; 60 Hz - 3 Ph. -- Combination head motor: 15 HP - 600 V; 60 Hz - 3 Ph. -- Table elevation motor: 1/4 HP - 600 V; 60 Hz - 3 Ph. -- Feed motor: 2 HP - 600 V; 60 Hz - 3 Ph. -- Spiral cutterhead dia.: 6''. -- TCT Tips dim.: 15 x 15 x 2 mm (228); (6) rows. -- Max. working width: 36". -- Min. working length: 12". -- Max. working thickness: 5". -- Sanding belt dim.: 37" x 75". -- Dust hoods dia.: 4'' x 2 & 5" x 2. -- Machine dim.: 71" L x 76" W x 77'' H. -- Net weight: 1,450 kG or 3,190 Lbs.

 704-841-2001

 Call
2011 Holytek HK-400  Planer
$19,100

HOLYTEK - HK 400, ...Top & Bottom PlanerSpecifications: -- 16" x 8" Cap., top & bottom helical insert knife heads, 4,000 RPM cutterhead rotation. -- 15 HP Top & 10 HP bottom; 10" min. stock length. -- 2 HP Variable feed speed from 23 - 65 FPM; sectional feed rolls & chipbreaker. -- 0.5 HP Motorized opening w/micro-adjustable table. Complete with: -- Heavy swing-out carriage with a built-in micro-dial; supports bottom cutterhead, pulled out for "quick & easy" replacement of knives.

 704-841-2001

 Call
J & P Machines DH 2N  Boring Machine
$9,450

J & P MACHINES - DH 2N, ...Double Hinge Drilling & InsertingDouble Drilling & Hinge Inserting Machine.Features: -- Fast setup from small to large doors. -- User-friendly movable head, which is easy to move to the preset stops. -- Pneumatic lock allows drilling at any distance. -- Quick-change hopper magazines with a loading capacity of (35) hinges. -- Insertion slide with UHMW non-wearing plastic. -- Creates chip-free bores on melamine and other sensitive materials by drilling from below. -- Boring heads with hardened gears and spindles. -- Linear bearings on slides for up & down movement. -- No tools required for precision depth adjustments. -- Double safety controls with: Metal detectors and photo eye prevent the boring unit from cycling again into the previously installed hinge. -- Dust extraction hoods with 4″ dia. -- Min. closing distance between heads is 7″ (180 mm). -- Max. opening distance is 60″ (1,520 mm); other sizes available upon request. -- PLC Control and proximity sensors. -- Emergency cord switch.Specifications: -- 2 HP - 3,600 RPM, 440 V, 3-Phase motors. -- Cycle time approx. (4) Sec. -- Compressed air 90 PSI. -- Weighs approximately 600 kG -- Dim.: 80″ L x 32″ W x 50″ H.

 704-841-2001

 Call
Contact Us
  • Toll Free & Canada: (800) 477-7606
  • Direct & International: (931)381-1638
  • Location: 2508 Pillow Dr. Columbia, TN 38401
Copyright © 2020 LumbermenOnline.com - All Rights Reserved