KAESER ASD 40 T 40 HP Rotary Screw Air Compressor, with Integrated Dryer & 17,702 Run & 3,775 Load Hrs (as of 2/16/24) Specifications: Rated cap. 191 CFM. Max. pressure 125 PSIG. Equipped with: 40 HP - 3,570 RPM TEFC Direct drive motor, IE3 (Premium Efficiency). "SIGMA PROFILE" Air end. 1:1 Motor-air end coupling. Wye-Delta reduced voltage magnetic starter. Electronic Thermo-Management (ETM) system. 2-Stage 4 micron air intake filter, with Cyclone pre-separation & replaceable element. Safety pressure relief valve. Anti-vibration mounts. Sound enclosure. KAESER "SIGMA CONTROL 2" PC-Based controller, with LCD Display & Touchpad. Complete with: Integrated Refrigerated Dryer. Compressor Operator Manual & Controller User Manual. Dimensions for this Specific Machine: 70" x 36" x 61" H. Weight for this Specific Machine: 750 kG (1,650 Lbs). CURRENCY NOTE: Negotiable Price is listed in U.S. Dollars.

KVAL COMMANDER Pre-Hung Door Machine/Door Line. Automated Cylindrical Lock and Hinge Machine for Pre-Hanging Interior & Exterior Doors; for doors Up to 2-1/4" thick x 4' x 9'; Routes, makes a 3° bevel on one side of the door edge. -- Traveling hinge router stops at each collar on the index shaft and tilts into approx. 3-1/2" to 5-1/2" hinge pocket on square or bevel doors. -- Selector switch allows sequencing for (2 - 3 or 4) hinges, 1/4" or 5/8" corner radius, and door/jamb or door only machining. Turret stops determine hinge size. -- Hinge index bar with embedded scale can be interchanged with other pre-set index shafts for rapid hinge center adjustments, or collars can be adjusted along the scale. -- Heavy Duty lock section features 5 HP face bore, 3 HP latch bore and 1.5 HP plate router; adjustable for 2-1/4" - 5" back-sets with self-centering clamp system for faceplate & latch hole; plate router adjusts for square or beveled face plates up to 12" long. -- Jamb clamps front load for easy handling self-adjust; there is no jamb width limitation. -- This machine can produce 250 or more doors per shift, including lock prep and hinge mounting to the door and hinge jamb.

KAY INDUSTRIES Phasemaster MA-1 5 HP Rotary Phase Converter.Features: 5 HP Largest single motor starting capacity; will run 10 HP total 3-phase machines from 1-phase input voltage. -- 208/230/460 Single-phase input voltage configuration available (please specify upon order). -- Less than 1% harmonic content, greater than 95% Power Factor & Operating Efficiency at full load; Heavy Duty General Purpose Design will operate any woodworking machinery; quiet running (1,800 RPM); produces true three-phase Delta output ideal for CNC equipment. -- The Phasemaster MA-1 provides instant motor reversing; buffered soft-start for three-phase loads which potentially reduce electrical operating costs; allows loads to develop full nameplate power ratings. -- Includes: 5-Year warranty. -- Does not include fuses or switch.Phasemaster MA-1-R includes factory-installed disconnect switch, fuses and terminal blocks in a side-mounted electrical enclosure for additional;...$ 522Optional LSV option for sensitive electronics add...$ 550

KAY INDUSTRIES Phasemaster MA-2, 10 HP Rotary Phase Converter.Features: 10 HP Largest single motor starting capacity; will run 20 HP total 3-phase machines from 1-phase input voltage. -- 208/230/460 Single-phase input voltage configuration available (please specify upon order). -- Less than 1% harmonic content, greater than 95% Power Factor & Operating Efficiency at full load; Heavy Duty General Purpose Design will operate any woodworking machinery; quiet running (1,800 RPM); produces true three-phase Delta output ideal for CNC equipment. -- The Phasemaster MA-2 provides instant motor reversing; buffered soft-start for three-phase loads which potentially reduce electrical operating costs; allows loads to develop full nameplate power ratings. -- Includes: 5-Year warranty. -- Does not include fuses or switch.Phasemaster MA-2-R includes factory-installed disconnect switch, fuses and terminal blocks in a side-mounted electrical enclosure for additional;...$ 500Optional LSV option for sensitive electronics add...$ 900

KAY INDUSTRIES Phasemaster MA-6, 30 HP Rotary Phase Converter.Features: 30 HP Largest single motor starting capacity; will run 60 HP total 3-phase machines from 1-phase input voltage. -- 208/230/460 Single-phase input voltage configuration available (please specify upon order). -- Less than 1% harmonic content, greater than 95% Power Factor & Operating Efficiency at full load; Heavy Duty General Purpose Design will operate any woodworking machinery; quiet running (1,800 RPM); produces true three-phase Delta output ideal for CNC equipment. -- The Phasemaster MA-6 provides instant motor reversing; buffered soft-start for three-phase loads which potentially reduce electrical operating costs; allows loads to develop full nameplate power ratings. -- Includes: 5-Year warranty. -- Does not include fuses or switch.Phasemaster MA-6-R includes factory-installed disconnect switch, fuses and terminal blocks in a side-mounted electrical enclosure for additional;...$ 7006Optional LSV option for sensitive electronics add...$ 1,200

KAY INDUSTRIES Phasemaster MA-8, 50 HP Rotary Phase Converter.Features: -- 50 HP Largest single motor starting capacity; will run 100 HP total 3-phase machines from 1-phase input voltage. -- 208/230/460 Single-phase input voltage configuration available (please specify upon order). -- Less than 1% harmonic content, greater than 95% Power Factor & Operating Efficiency at full load; Heavy Duty General Purpose Design will operate any woodworking machinery; quiet running (1,800 RPM); produces true three-phase Delta output ideal for CNC equipment. -- The Phasemaster MA-8 provides instant motor reversing; buffered soft-start for three-phase loads which potentially reduce electrical operating costs; allows loads to develop full nameplate power ratings. -- Includes: -- 5-Year warranty. -- Does not include fuses or switch.Phasemaster MA-8-R includes factory-installed disconnect switch, fuses and terminal blocks in a side-mounted electrical enclosure for additional;...$ 1,500Optional LSV option for sensitive electronics add...$ 3,600

KAY INDUSTRIES Phasemaster MA-1B, 7.5 HP Rotary Phase Converter.Features: 7.5 HP Largest single motor starting capacity; will run 15 HP total 3-phase machines from 1-phase input voltage. -- 208/230/460 Single-phase input voltage configuration available (please specify upon order). -- Less than 1% harmonic content, greater than 95% Power Factor & Operating Efficiency at full load; Heavy Duty General Purpose Design will operate any woodworking machinery; quiet running (1,800 RPM); produces true three-phase Delta output ideal for CNC equipment. -- The Phasemaster MA-1B provides instant motor reversing; buffered soft-start for three-phase loads which potentially reduce electrical operating costs; allows loads to develop full nameplate power ratings. -- Includes: 5-Year warranty. -- Does not include fuses or switch.Phasemaster MA-1B-R includes factory-installed disconnect switch, fuses and terminal blocks in a side-mounted electrical enclosure for additional;...$ 500Optional LSV option for sensitive electronics add...$ 900

KENTWOOD M 609X Feed Through Moulder; 6-Head (B-R-L-T-T-B), working cap. 9-1/16"" x 6". Head sequence & Spindles: -- Bottom 10 HP, right 10 HP, left 10 HP, top 20 HP, top 20 HP and bottom 15 HP motor. -- Spindle dia.1 13/16" with cutterhead speed of 7,200 RPM. -- All spindles equipped with mechanical digital readouts. Mechanical readouts for pressure elements and chipbreakers.Electric brakes on spindles 2 through 5, Cutting circle of vertical spindles: 125 mm to 200 mm (4,7" X 7.8") Cutting circle of horizontal spindles: 125 mm to 200 mm (4,7" X 7.8"). Feed works: -- Cardan feed-works drive system with pneumatic pressure rollers, Inverter driven 5 HP feed system with feed speeds of 20 - 98 FPM. Infeed. -- Complete with: Full width driven bottom in-feed roller before first head, Serrated steel feed rollers before top horizontal head.Rubber coated feed rollers after top horizontal head, (2) Rollers above and (1) in the table prior to first bottom spindle; (2) additional powered rollers in the table. -- In-feed table 2M (72"), chromed tables and fences. Includes: -- Central lubrication, manual table lubrication pump. -- Side pressure roller mounted to infeed table, Short stock attachment at right spindle for short part, -- Sound enclosure and Interior cabin light. Note: Floor space: 77" W x 166" L x 68" T, Machine weight: 10,800 lbs.

MAREN - 72, ...Auto-Tie Horizontal Baler w/Infeed ConveyorSpecifications: -- Cylinder: 6". -- Bale size: 30" x 38" x Variable. -- Feed opening: 29" x 27". -- Power unit: 20 HP. -- Tensioner cylinder: 3" x 12". -- Cycle time: 20 Sec. -- Operating pressure: 2,700 PSI. -- Conveyor: 48" Infeed included.Applications: -- Shredded corrugated, folding carton stock, and coated stock. -- Molded fiber products. -- Shredded paper. -- Textile. -- Foam. -- Aluminum cans (UBC). -- Steel Cans.

MARINUS Powermax 300 HD End Matcher With Defecting, Cut to Length & Optimizing Cut-Off CapabilitiesFeatures & Specifications: -- Heavy and stable construction -- Cutterhead Carriage and Clamp System utilizes HD Lineal Bearings – grease lubricated. -- Heavy Duty – low maintenance Feed Chains Into machine and takeaway of material after cutting/ end matching. -- Continuous high-speed feeding system with accurate positioning utilizing HD Servo Drives. -- 2 Servomotors for maximum feed control and acceleration and deceleration control -- Servo-driven feed motor & gearbox for highest efficiency speed feeding and control of the cutterhead carriage includes independent step-less speed control forward & reverse. -- Pneumatic side pushers (holding material firmly against the fence) for guaranteed square angle cut. -- 2 Cut-off sawing servo motors: 5 HP each (3,0 kW) – 450 mm (17.7";) dia. blades with inverters (VDFs) for varying blade speed -- 2 High-speed milling head servo motors with inverter (VFD) (12HP - 7,5 kW each) with speeds to 12,000 RPM - 5"; (125 mm) dia. -- Adjustable cutterhead stroke based on material width to increase throughput speed based on the width of material input. -- 1 Luminescence-Sensor camera for defect crayon mark -- Inductive-Sensors – for detecting the position of the carriage and the others for detecting the positions of the saw blades. -- Cutoff waste powered belt conveyor in machine (below feed system- 12"; from floor) with drive motor for waste cutoff pieces taken to the outfeed end of the machine. Other Technical Specification: -- Machine is completely enclosed by safety doors. -- Machine is produced to CE Safety and Electrical Standards to UL/CSA Standards -- Lenze PLC Control -- Operation from operator’s control with touch screen control – mounted on the front right cover of the machine. -- Air pressure required – 85 PSI (6 Bare) -- 1x 8"; (200 mm) & 2 x 4.75"; (120 mm) dia dust outlets with approx. 5,000 to 5,500 mm and from 3050 to 3350 CFM -- Router Remote Access – with an internet connection, factory can monitor the performance of your machine. Also allows for easy access to service and softwareupdates and downloadsInput & Output Material Specifications -- Board Widths: 2";(50mm) Min. to 12.28";(312mm) Max. Min width 1.75"; (44.5 mm) min. -- Board Input Lengths: 17.9"; (450 mm) Min. to 20 ft.(6000mm) Max. -- Board Output Lengths: 15.9"; (400 mm) Min. -- An available short-piece option can be added to reduce output. length to 10"; (250mm) Min -- Board Widths: 2";(50 mm) min. to 12.28";(312 mm) max. -- Board Input Lengths: 17.9"; (450 mm) Min. to 20 ft. (6000 mm) Max. -- Board Thickness:4"; (10 mm) Min. - (to 0.315"; (8 mm) on request) (to 2"; (50 mm)Standard Programs / Programming -- The machine is equipped with 2 Primary Programs: -- 1. Endmatching – includes trimming ends and endmatching -- 2. Cutting only (no endmatching) -- 3 Sub-Programs -- 1. Defecting

MARCUS TRANSFORMER 15 KVA, 3-Ph, Auto, 600/480 V Transformer with tap for 440 V.15 KVA Auto-ventilated "dry type" transformer 600 V in (primary); 480 V out (secondary) with tap on secondary for 440V at full capacity. -- Manufactured with grain oriented silicon steel is used. -- Coil windings with high quality magnet wire and the enclosure is made of heavy gauge steel w/ventilation openings. -- UL and CSA approved.

MARTIN T 45 Planer, Heavy Duty24" Width and 1/10" to 9-27/32" opening, 10 HP motor.Specifications: -- 4-Knife 5" dia. TERSA cutterhead belt driven @ 5,000 RPM, max. cutting depth 3/9", 12" min. stock length unbutted. -- Variable feed speed 16 - 82 FPM, 3-1/3" dia. self-cleaning rubber feed rollers, sectional pressure bar. -- Motorized raise-and-lower bed by (4) screw jacks w/LED readout, table size 49-1/2" x 25". Complete with: -- Emergency stop, magnetic starter w/overload protection. -- Tool compartment, electric brake, centralized lubrication & 6-1/3" dia. dust extraction outlet.

--In auction: https://exfactoryauctions.com/Detail/SH-230492/event/A122024$1 --NO RESERVE!-- MARTIN T 23 Tilting Spindle Shaper, with 30 mm (1.18") Interchangeable Spindle & Power Feeder Specifications: Table size 940 x 1100 x 850 mm (37.01” x 43.31” x 33.46”) H, with Table insert dia. 90, 130, 205, 305, & 480 (3.54”, 5.12", 8.07”, 12.01”, & 18.90”). Spindle tilt 0° to 45°. Maximum capacity under nut 7". Vertical spindle adjustment 145 mm (5.71"). Spindle speeds 3000, 4,500, 6,000, & 90,000 RPM. Equipped with: 6.4/7.8 HP Motor. "MK5" Spindle shaft. Mechanical spindle brake, with Foot pedal. Hand spindle lock. Complete with: 11-1/2” x 4-3/4” Left & Right Fences, with 21” x 6” H Left & Right Wood fences. 1996 CO-MATIC 1 HP 4-Speed 4-Roll Power Feeder, with Speeds 13, 26, 26, & 72 FPM. Dimensions with Power Feeder: 42" x 42" x 63” H.

MASTERWOOD PROJECT 313 CNC MACHINING CENTER (W/ACT/BORING): -- Specifications:Working Capacity:"X" Axis 3,080 mm (121"), "Y" axis 1,100 mm (43") width; -- Positioning Speed:Programming speed in X-axis 197 FPM (60 MPM), Y-axis 162 FPM (49 MPM), Z-axis 58 FPM (18 MPM). -- Boring unit:(13) independent vertical spindles, (9) in X-axis, (5) in Y-axis; (4) horizontal spindles with (1 + 1) in X-axis for edge boring in the left- & right-hand panel edges. -- Machining:(1) 7.5 HP (5.6 kW) high speed router (1,000 - 24,000 RPM) by frequency inverter; 1.5 HP (1.1 kW), 6,000 RPM grooving saw with manual rotation for X-axis or Y-axis; -- Work Table: (6) moveable support rails with (2) vacuum cups ea., double zero settings, (6) pneumatic backstops and (2) pneumatic side stops creating (2) working zones. -- Operator & Machine Control:TECNOSUD "K68800" Microprocessor control for (3) axis, lineal, circular, and helical interpolation. Equipped with 14" color video graphic monitor, keyboard for data entry, 1.44 MB floppy disk drive, 64K RAM, RS-232 for possible connection to office PC, all mounted in separate free-standing control cabinet; features to run CPL/Parametric "TRIG" programming and "Spline" CAD/CAM. -- Complete with: Dual zone vacuum pump. Ontario Hydro approved electrics. -- Actual Model is MASTERWOOD PROJECT 313

MASTERWOOD OMB1CN3-TF Horizontal Slot Mortiser. One NC working head (3) axis with programmable microprocessor.. Machines a sequence of slots on windows, doors, shutter, or cabinets without moving workpiece. Continuous cycles with loading/unloading. -- Equipped with: (1) Maka style chisel mortising unit, (1) Vertical routing unit and (1) TF Horizontal routing unit. High frequency drilling - routing with controlled axis, DC motors, ball screw driven. -- Max Mortise workpiece size 150x110x2800 mm length, (5.9"x4.3"x110.2"). Vertical and horizontal routers 142"; length. -- Max slot depth 130 mm (5.1"). Max vertical head stroke 140 mm (5.5"). -- Features: Pneumatic hold-downs bar mounted above table. Flip-up pneumatic pressure beam for additional support when needed. Free-standing control and electrical cabinets house computer monitor and keyboard. Master universal electronic system controller (MW CN10 Centromac) -- Vertical routing assembly: 4HP, 220/380v 3 PH, 9,000 RPM -- Horizontal routing assembly 5"; 220/380v, 3 PH, 9,000 RPM -- Memory for 50 cycles. Mirror imaging with preset tool speed (over-writeable knob). -- Total load 21 KVA -- Overall dimensions 4200mm long x1600x1600mm (166"x63x63"). Electrical cabinet 1,000 high x 450x950mm (40"x 18"x38"). Approx. weight 3800 Kg (8,400 Lbs.).

MATH-EX (6) PERSON BASIC RECYCLING SORT LINESpecifications: -- 16 Feet x 32" Inclined feed conveyor with 48" high hopper and 2" high cleats @ 36" centers. -- 36 Feet x 32" Sort conveyor with infeed transition guides and Belly rest skirt on one side. -- Sort platform with OSHA stair and handrail. -- (6) Sort chutes with 52" of clearance. -- 1-1/2 HP, 460 volts 3-phase drives.Custom order your Sorting Line with approx. 7 to 8 week lead time for delivery.

MATH-EX (6) PERSON BASIC RECYCLING SORT LINE -- 16 Feet x 32" Inclined feed conveyor with 48" high hopper and 2" high cleats @ 36" centers. -- 36 Feet x 32" Sort conveyor with infeed transition guides and Belly rest skirt one side. -- Sort platform with OSHA stair and handrail. -- (6) Sort chutes with 52" of clearance. -- 1-1/2 HP 460 volts 3 phases drives. -- (2) VFD Controllers mounted in control panel -- Pedestal style stand. -- Emergency pull cord stop or-E-stop for sort conveyor -- Motor wire and flex conduit for (2) conveyors shipped loose. -- BRAND NEW WITH WARRANTY -- ALLOWS 7 TO 8 WEEKS DELIVERY -- LOADED ON YOUR TRUCK

MATH-EX (6) Position (Person) Basic Recycling Sort Line Specifications: -- 16 Feet x 32" Inclined feed conveyor with 48" high hopper and 2" high cleats @ 36" centers. -- 36 Feet x 32" Sort conveyor with infeed transition guides and Belly rest skirt one side. -- Sort platform with OSHA stair and handrail. -- (6) Sort chutes with 52" of clearance. -- 1-1/2 HP, 460 volt, 3-phase drives. -- (2) VFD Controllers mounted in control panel -- Pedestal style stand. -- Emergency pull cord stop or-E-stop for sort conveyor -- Motor wire and flex conduit for (2) conveyors shipped loose. -- (1) 6" Diameter Ceramic Drive Pulley -- (1) Stainless steel Back ChuteOptional Equipment: -- (2) VFD Controllers mounted in control panel -- Pedastal style stand -- Emergency pull cord stop or E-Stops for sort -- More wire and flex conduit for (2) conveyors

MATH-EX 4-Position (Person) Basic Recycling Sort Line Specifications:SLIDER BED BELT CONVEYOR: (MODEL 600, STYLE B) FRAME CONSTRUCTION: 10 GAUGE, BOLT TOGETHER PULLEY DIAMETER: 6" DIAMETER CONVEYOR LENGTH: 16' 0" ANGLE OF INCLINE: 25° EFFECTIVE WIDTH: 32" BELT: BLACK PVC120 COS ENDURA-CLEAT: 2" HIGH @ 48" CENTERS SIDE SKIRTS: 12" HIGH (TOB), 12 GAUGE BELT RETURNS: BOTTOM PANS BELT SPEED: 60 FPM DRIVE MOUNT/SIDE: SHAFT MOUNT, RIGHT HAND SIDE MOTOR: 1 HP, 460V/3PH LIVE LOAD CAPACITY: 394 LBS. (FIXED SPEED) CONTROLS: START/STOP CONTROL - (2) E-STOPS - MOUNTED AND WIRED INFEED HEIGHT: 0" BOF DISCHARGE HEIGHT: 83" BOF SUPPORTS: PROVIDED INCLUDED FEATURES: - BLACK SIDE GUIDES - BOTTOM PANS - INFEED HOPPER - TRANSITION GUIDES - MAGNETIC HEAD PULLEY (CERAMIC) OVERALL FLOOR LENGTH: 174" (END TO END) APPROXIMATE SHIPPING WEIGHT: 1876 LBS. PLUS PACKAGINGFRAME CONSTRUCTION: 10 GAUGE, BOLT TOGETHER PULLEY DIAMETER: 6" DIAMETER CONVEYOR LENGTH: 26' 0" ANGLE OF INCLINE: 0° EFFECTIVE WIDTH: 32" BELT: BLACK PVC120 COS SIDE SKIRTS: 6" HIGH (TOB), 12 GAUGE BELT RETURNS: RETURN ROLLERS BELT SPEED: 60 FPM DRIVE MOUNT/SIDE: SHAFT MOUNT, RIGHT HAND SIDE MOTOR: 1 HP, 460V/3PH LIVE LOAD CAPACITY: 922 LBS. (FIXED SPEED) CONTROLS: AC VFD CONTROL - (2) E-STOPS - MOUNTED AND WIRED INFEED HEIGHT: 52" BOF DISCHARGE HEIGHT: 54" BOF SUPPORTS: PROVIDED INCLUDED FEATURES: - BLACK SIDE GUIDES - SORT SKIRTS - (4) SORT CHUTES OVERALL FLOOR LENGTH: 312" (END TO END) APPROXIMATE SHIPPING WEIGHT: 2059 LBS. PLUS PACKAGING4P SORT PLATFORM: LENGTH: 23' WIDTH: 42" HEIGHT: 26" ADDITIONAL FEATURES: - SAFETY RAILINGS

MATTEI OPTIMA 30, 40 HP Variable-Speed Rotary Vane Compressor (89-189 CFM @ 102-145 PSIG)RELIABLE ROTARY VANE AIRENDSThe inverter adjusts the motor’s rotational speed, adapting the air delivered by the compressor to the actual air demand. OPTIMA can save up to 35% of the annual operating costs. Ideal for automotive, commercial and industrial applications.Features: -- MATTEI Optima Series Air Compressors quiet cabinet constant-duty Rotary Vane Compressors feature an inverter to match their operation to suit the load profile required by the compressed air system to ensure maximum energy savings under varying air demands.Equipped with: -- 40 HP TEFC motor, 89-189 CFM @ 102-145 PSIG; MaestroXS microprocessor control and protection system, AC inverter, premium efficient TEFC motors, quiet acoustic enclosure, air-cooled aftercooler, intelligent timed electronic condensate drain and separator kit and are filled with Mattei Rotoroil 8000 F2 synthetic oil; 2" NPT outlet.Includes: -- “W"; Version includes water-cooled oil and after cooler, add;...$ 1,463