DIEHL - DMG -12, ...Profile GrinderSpecifications: -- 1/2" Width cap. and 10-1/2" max. cutting circle. -- 1 HP TEFC Motor with 2,260 RPM grinding spindle. -- (2) 1-13/16" Dia.; 16" X-axis & 6" Y-axis table movement. -- 30° Clockwise & 90° counterclockwise base swivel rotation for face grinding of profile cutters or planer knives. -- +30° to -30° Vertical grinding spindle adjustment. -- 2" In & out adjustment. -- 1" X-Axis & 1-7/8" Y-axis template adjustment. -- 7" Min. & 10" max. grinding wheel dia.Equipped with & Features: --Coolant pump with 5-gallon tank.

DISA CS-4 MAXI Dust collector with Rotary Air Lock. Approx. 16,000 CFM at 8.7:1 air-to-cloth ratio; 1,725 sq. ft. of filter area, with (128) filter bags filtering to 3-micron. -- General Info: CS-4-M consists of (3) filter modules & one entrance module. -- Comes with: DISA, S56-500 Material Handling fan powered by 50 HP TEFC motor. Fan nominal rating: 16,000 CFM @ 9" SP. Fan is currently mounted on elevated support but can be installed on the ground as well. -- (3) Reverse air bag cleaning modules with motorized fans that clean the bags every (4) hours of operation automatically, each with 2 HP fan motor. A damper at inlet closes during cleaning cycle to prevent blowback. -- Complete with: Hopper bottom as collected dust is conveyed to one end where a NRS-20 Rotary Air Lock where dust is discharged into Transfer fan. Filtered air return unit, 8' support structure to allow for dumpster under Dust Collector. -- Includes: Control panel, motor starters and switches, and Explosion Panels. Material handling main fan w/motor mounted to side of base module. -- 26" diameter inlet pipe, 97" clearance under collector for dump hopper, free standing steel bolt-together structure, -- Features: Dust transfer from bottom of Rotary Air Lock to enclosed container by separate floor mounted material handling fan, approx 7.5 HP. -- Note: Pictured storage bins are not included.

DISA NFK 9 - 2BL Modular Dust Collector. Up to 45,000 CFM @ 6.25 to 1 air-to-cloth ratio, and @ 11.6" w.g. external static pressure; modular, expandable Heavy Duty Baghouse. -- 7,200 Sq/ft of filter area, mad up of (450) filter bags. -- Filter consists of (9) Filter module sections with access door in each section and (2) blank inlet module sections with (9) 2 HP regeneration fans for cleaning of filter media and (2) blank entry modules. -- Comes with: (1) 60 HP Belt drive COMBIFAB blower package w/drive guards; motor & fan are a common steel base/frame with ground level installation. Fan delivers about 20,000 CFM. There is sufficient filter capacity for at least 75 - 100 HP second fan/motor. -- Complete with: Outside separate elec disconnects for each cleaning fan. -- "NRS-10" Rotary air lock for bottom discharge with 2 HP TEFC motor; Steel support members dismantled.. -- Includes: Some outside pipe (and main headers explosion/access doors -- Note: (2) cleaning fans are missing and will be supplied at cost. -- Actual model is NFK2000 9+2 BL HJLR.

DONALDSON / TORIT DWST6-5 Cartridge Dust CollectorDownflo® WorkStations (DWST) fit anywhere on the plant floor and apply NO restrictions to worker movements or visibility. The full line of WorkStations are designed specifically for those in-plant areas where dirty and/or noisy operations are out in the open—grinding, sanding, chipping, batch mixing or welding. The DWST delivers exceptional performance in metalworking, woodworking, and process applications where high filtration efficiency and ledge less construction is often a requirement. Specifications: -- (5) Module System, each with 10 HP motor, 7,000 CFM. -- (4) Ultra-Web cartridges. -- Pulse-cleaning manifolds and ventures, (2) dust drawers. -- (1) Acoustical panel per module. Louvers mounted on lower section of unit.Includes: -- (1) IEC control panel includes 460-volt motor starters, circuit protection for each motor, transformer, programmable logic controller. -- Magnehelic gauge mounted in a panel door, start/stop buttons, and a through-the-door disconnect switch. -- Pulse cleaning can be continuous or after-shift. -- All components are IEC rated. The enclosure is rated Type 12. -- 1"; Compressed Air Regulator with Filter Separator and Gauge, Black Iron Fittings, and Black Iron Piping Required for Cleaning System. -- Provides a 1"; Common Connection Point for Design Shutters to Tie into with Existing Compressed Air System.

DONALDSON / TORIT - 2DF-16, ...Cartridge Dust CollectorSpecifications: -- Holds (16) cartridge filters. -- Includes "New" AirMax Premium Media Cartridge Filters: Fire retardant. -- Total filter media area: 3,616 ft². -- Air-to-Media ratio @ 8,000 CFM is 2.2:1. -- Automatic Pulse Clean System with: Differential pressure gauge and sequencing control in enclosure. -- (2) Hopper outlets with sealing drum cover kits. -- Steel support structure. -- Includes: 20 HP Top mount, direct-drive Blower. -- Rated for 8,000 CFM. -- Electrical motor starter & controls. -- Includes: Installation/Operation/Maintenance Manuals.Sold with 6-Month Mechanical Warranty

DOUCET ERS-96/RS-75/AP-508 MULTI-BLADE PANEL GROOVE/RIP SAW SYSTEM:The Doucet ERS-96/RS-75 Automated Panel GROOVE/RIP Saw System is designed to GROOVE and/or RIP panels as well as edge the sides of core materials. Ideal for plywood, OSB, MDF, HDF and other composite panels.This Line was originally designed for Engineered Flooring Blanks.ERS-96 Grooving Specifications:40 HP - 3,500 RPM belt driven saw arbor motor. Material width cap. 96" maximum. Material thickness 0.5" - 0.625" maximumGrooving pattern on 4" centers across the 96" width of panel. Depth and width of groove approx. 3/16" kerf/width by 1/8" deep.3" dia. Arbor shaft with 1.5 HP motor for motorized arbor adjustment for panel thickness. Saw arbor accessible from above for tool changes. -- Feed system:5 HP - 1,750 RPM feed motor, variable feed speed up to 75 FPM.(4) Powered bottom feed rollers & adjustable top idler pressure rolls with positive panel support during grooving operations.Top & bottom feed rollers have slip resistant urethane covered rollers, feed rollers are chain driven with air tensioning. -- Complete with:Dynamic saw arbor brake; Infeed anti-kickback fingers; Saw blade safety interlock cover; 12" dia. dust collection outlet (4,000 CFM required). RS-75 Ripping Specifications:40 HP - 3,500 RPM belt driven saw arbor motor. Material width cap. 60" maximum. Strip width cap. 2.5" minimum. Depth of cut 0.25" - 0.75" (6 - 19 mm) maximum.3" dia. Arbor shaft with 1.5 HP motor for motorized arbor adjustment for panel thickness. Saw arbor accessible from above for tool changes. -- Feed system:Doucet AP-508 Automatic panel feeder with scissor lift to automatically feed panels as needed.5 HP - 1,750 RPM feed motor, variable feed speed up to 75 FPM.(4) Powered bottom feed rollers & adjustable top idler pressure rolls with positive panel support during grooving operations.Top & bottom feed rollers have slip resistant urethane covered rollers, feed rollers are chain driven with air tensioning. -- Operator Interface: Doucet OI/HMI Control System for automatic loading & stacking with minimal human intervention other than a forklift operator to bring in new material and remove the processed parts/strips. -- Complete with:Dynamic saw arbor brake; Infeed anti-kickback fingers; Saw blade safety interlock cover; 12" dia. dust collection outlet (4,000 CFM required). -- Options Include: (1) Doucet AP-508 Automatic panel feeder with Indexing scissor lift. (1) Cross Transfer Chain Conveyor to feed panels sideways by the long edge through the Groover, max width 96". (1) Cross Transfer Chain Conveyor to feed panels short end wise through the panel RIPSAW, max. width 60" (1) Outfeed Lift Table to automatically stack ripped strips. Maximum weight of stack: approx. 5,000 LBS. -- Actual Model is DOUCET RS-75/ERS-96/AP-508

DOUCET BT3-30-5-23-G-PT Return Conveyor for EdgebandersSpecifications: -- Right-hand feed, with Left-hand return. -- Min. part size 4" x 12". -- Max. panel size (with operator assistance supporting then turning panels) 45" x 96".Equipped with: -- 1-1/2’ L Infeed roller conveyor section, with (5) 23-1/4"; W & (2) 34-1/4"; W Rollers. -- 34-1/4"; W x 5-1/2’ L x 35"; H Receiving table, with Automatic/Manual height adjustment 2". -- (8) 3/8"; Dia. transfer belts, (3) on 3"; Centers, (2) on 6"; Centers, & (3) on 9"; Centers. -- 29-1/2"; W x 5-1/2’ L x 34"; H Return table. -- 29-1/2"; W x 18’ L x 34"; H 3-Section Return conveyor, with 5-1/2"; W x 6’ L Gravity roller conveyor side extension. -- All rollers 1-7/8"; Dia. covered line shaft on 3"; centers.

DURA-QUIP - VC-3532, ...Vibrating Conveyor: -- Specifications:35" Wide x 32' Long; Pan is 7" deep and has 1/4" round holes punched plate in most of length to allow sawdust to drop outside of Conveyor. -- Bottom frame is filled with concrete 12" deep and rests on coil springs to isolate vibration from the ground. Buyer to replace screens. -- Include: 10 HP TEFC 460 V Drive motor.

DUST TECHNOLOGY DT-250 Modular Dust Collector Free-standing self-contained internal air system, 25 HP Motor;Specifications: -- Rated for 9,800 CFM, 5-bag unit, 75 cu. ft. collection capacity. -- (5) Upper cloth filter bags with 165 sq. ft. filter area; 16" inlet dia., dust baffling system to fill bags evenly. Supplied with & Includes: -- 25 HP motor with magnetic starter, -- (5) Upper cloth filter bags and (5) lower plastic collection bags. -- (5) Double "T: Bolt straps. -- (5) Quick release metal straps. Three Year Comprehensive Warranty

DUST TECHNOLOGY DT-200 Modular Dust Collector Free-standing self-contained internal air system.Specifications: -- 20 HP Motor, rated for 7,500 CFM, 4-bag unit, 60 cu. ft. collection capacity. -- (4) Upper cloth filter bags with 132 sq. ft. filter area; 14" inlet dia., dust baffling system to fill bags evenly. Features & Includes; -- 20 HP motor, magnetic starter; -- (4) Upper cloth filter bags and (4) lower plastic collection bags. -- (4) Double "T: Bolt straps. -- (4) Quick release metal straps. -- Magnetic starterThree Year Comprehensive Warranty

DUST TECHNOLOGY DT-50 Modular Dust Collector5 HP BALDOR Motor, compact 2-bag free-standing & self-contained Heavy Duty Dust Collector, rated @ 2,400 CFM, 9" - 11" static pressure at fan. -- Equipped with: 10" Inlet dia., (2) Cotton Filter bags with 66 sq. ft. filter area and (2) Plastic Collection Bags w/ 30 cu. ft. collection capacity. -- (2) Double "T" Bolt Straps and (2) Quick Release Metal Straps. Includes: Magnetic Starter

LHI 72" RFPR Wide Arbor Roll Feed Gang Panel Ripper with Custom 5' x 16' Automated Infeed -- Specifications: -- 30 HP Arbor Motor; 1/8" min. to 1-1/4" max. material thickness and 72" cutting width. -- 10" Dia. blade design cuts thru max. 2" thickness; -- 3-15/16" dia. arbor with 72" of usable width cutting capacity, min. panel length 30". -- 1-15/16" FAFNIR arbor bearings; with (8) steel feed rollers on 6" centers; fixed feed speed of 80 FPM -- 47-1/4" working height -- (1) Arbor Cart is included -- (2) 4" Dia. dust collection ports on top and (1) 8" dust collection port on bottom. Recommended 1,500 CFM Includes the Following Optional Items: -- 5-Strand powered Chain Deck; 12' long; arranged to feed 5' x 16' packages onto the Scissors Lift. Complete with controls for forward, reverse, and jog. -- 5-Sections of Gravity Rollers on Scissors Lift Deck -- 8,000 lbs. Infeed Tandem Scissors Lift with 5' x 17' Deck and 2-HP, 3-Phase Motor. Lift includes a backstop for initial alignment at the Rake Feeder -- (8) Polyurethane Rollers on 6" centers -- Variable Feed Speeds from 10 to 80 FPM. -- Rake Feeder for 16' long panels -- Auto-cycle for Rake Feeder. -- 6' Line Up Conveyor with Fence and Powered Pinch Roll Included Tooling: -- (36) Standard Saw Collars for Ripping -- (72) Standard 10" Sawblades for Ripping (Includes a spare set) -- (37) Standard Throat Plates for RippingQuick Setup Kit Included, Contains the Following -- Belt guide -- Belt Tensioner -- Hydraulic Arbor LockAdditional Arbor Setup Included. Contains the Following: -- Arbor Cart -- Cart -- Blade Box -- Arbor -- Bearings -- Sheave -- Throat Plate Rack -- (6) Throat Plates PRICE REFLECTS FACTORY'S 7% MATERIALS SURCHARGE ON $156,995, OR $10,990

LHI MODEL RFPR AUTOMATED PANEL RIP SYSTEM --Arranged for up to 5/8"; Thick x 52"; Wide x 18’ Long Panels as follows: AUTOIMATIC INFEED SYSTEM, INCLUDES: --Rake Feeder for up to 18’ Long Sheets --Automated Feed Cycle Controls --Turnkey Controls, Plug it in and Run --1 HP, 3-Phase, 460-Volt Operation 6’ ALIGNMENT CONVEYOR, INCLUDES: --Gravity Roller Frame with 60"; Wide Rollers --Alignment Fence --Spring Loaded “Feather"; to Keep Sheets Tight to the Alignment Fence --Powered Feed Wheel to Push Sheets into the Ripsaw --2 HP, 3-Phase, 460-Volt Operation TANDEM INFEED SCISSORS LIFT --8,000 LBS. Capacity --30"; x 204"; Platform With 62"; Rails Mounted Across the Lift for Fork Lift Entry. Rails are Evenly Spaced Down the Length of the Lift --62"; x 204"; Useable Deck Size. --Automatically Raised and Lowered by Signals from the Sheet Feeder --2 HP, 3-Phase, 460-Volt Operation TANDEM OUTFEED SCISSORS LIFT --8,000 LBS. Capacity --30"; x 204"; Platform With 62"; Long Rails Mounted Across the Lift for Fork Lift Entry. Rails are Evenly Spaced Down the Length of the Lift --62"; x 204"; Useable Deck Size. --Automatically Lowers by Signals from Auto-Down Index Control Unit --2 HP, 3-Phase, 460-Volt Operation --OPTIONAL: 4-Sided “Accordion Skirts"; for each Tandem Lift Table, add $2.650 per lift RFPR" ROLL FEED PANEL GANG RIP SAW --50 HP Main Arbor Motor --1/8" Min. To 1-1/4" Max. Material Thickness x 72" Cutting Width --10" Dia Blade Design; 3-15/16" Dia. Arbor with 72" of Usable Width Cutting Capacity --Min. Panel Length 30". --1-15/16" FAFNIR Arbor Bearings --(8) Polyurethane Feed Rollers on 6" Centers --Variable Feed Speeds Via VFD --(1) Quick Blade Change-Out Kit --(1) Additional Arbor Cart --(2) 4" Dia. Dust Collection Ports on Top and (1) 8" Dust Collection Port on Bottom. Total Recommended 1,500 CFM. TOOLING: --(20) Saw Collars, Mount Directly to the Arbor with a Set Screw --(20) Saw Blades Configured for Clean Cuts on Your Panels

LHI RFPR-72/16 "HEAVY DUTY" MULTI-BLADE PANEL RIP SAW (W/LOADING/UNLOADING): -- Specifications (1) 30 HP Main arbor motor for 1" min. - 5" max. material thickness;16" Dia max. blade capacity with 1.25" minimum spacing between the blades;Minimum panel length 30" with 72" of usable width cutting capacity.3-15/16" Dia. arbor with 1-15/16" precision arbor bearings;Positive powered steel contact feed rollers with (8) adjustable Polyurethane drive rollers;Variable feed speed to max 80 FPM.Available Options Include:Single point height adjustment for materials from 1" to 5" thickness using customer supplied 16" dia blades(note: Ripping widths can never be less than one-half the material thickness).(1) "Quick Change" arbor cart trolley and blade box for QC set ups.(12) Saw collars to attach the customer supplied 16" dia. diamond blades to the arbors(1) In-feed Scissors Lift with auto cycle controls(1) In-feed 6' conveyor with alignment fence and powered assist feed(1) Auto sheet feeder with auto cycle controls(1) Out-feed Scissors Lift with 4 x 8 roller top.Installation technical assistance for $125/Hr plus travel time and expenses, payable upon competition of services. NOTE:Quote is valid for 30-days;Quoted price is FOB, Factory;Customer is responsible for off-rigging cost at their facility;Customer is responsible for spotting the machine to its final resting place with adequate floor foundationCustomer is responsible for adequate electric, air & dust control supply upon technician's request:Warranty: 1-yr mechanical parts (electrical controls excluded);Delivery to Customer's facility is approx 17 weeks from receipt of funds;Quote assumes customer will deliver material for testing & run-off procedures (if required);NOTE: PRICING DOES NOT REFLECT FACTORY'S 10% MATERIALS SURCHARGE

LHI RFPR 72/12 "HEAVY DUTY" MULTI-BLADE PANEL SAWSpecifications -- (1) 50 HP main arbor motor for 1/8" min. - 2" max. material thickness; 12" Dia max. blade capacity with 1.25" minimum spacing between the blades; Minimum panel length 30" & 72" of usable width cutting capacity. -- 3-15/16" Dia. arbor with 1-15/16" precision arbor bearings; positive powered steel contact feed rollers with (8) Polyurethane drive rollers; variable feed speed to max 80 FPM. -- (1) "Quick Change" arbor cart trolley and blade box for 9 1/2" cutsOn average this machine will cut a bundle (42 sheets) of 3/4" Plywood. LVL, PB, MDF or OSB into narrow strips in 4 minutes or less.Available Options: -- Blade Box Arbor Cart and Trolley $ 12,590.00 each -- Arbor Carts modifications to accept 12" dia. blades $ 700.00 each -- Single Point Height Adjustment $ 6,000.00 each -- "Quick Change" set up kit (includes belt guide, belt tensioner, and hydraulic arbor lock) $ 3,695.00 each -- Tandem 8000# capacity infeed Scissors Lift, 2 HP, 3 Phase, 230/460 Volt, 31" x 192" platform and cross bars for fork truck entry $ 14,495.00 each -- Tandem 8000# capacity outfeed Scissors Lift, 2 HP, 3 Phase, 230/460 Volt with 48" x 192" platform and beveled crossbars for fork truck entry and auto down indexing $ 16,390.00 eachTooling Cost: -- Carbide Tip Blades 12" x 40T x 4 3/16 bore with TCG and 3 pin holes $ 125.00 each -- Saw Blade Tooling Collars $ 125.00 each -- Actual Model is LAUDERDALE-HAMILTON RFPR "HEAVY DUTY" 12 Panel Rip SawNOTE: PRICING DOES NOT REFLECT FACTORY'S 7% MATERIALS SURCHARGE

LHI 96" x 60" ANGULAR TYPE RIP & CROSS-CUT SYSTEM: Specifications: -- Automatic Angular Rip & Crosscut 5-Position System; max. panel size of 8' (96") long x 5' (60") wide x 1" - 4" thick; 1.25" minimum spacing between the blades; variable feed speed from 0 - 150 FPM. This system will process a unit of material in approx. (7) Min. -- Pos. # 1: LHI Automatic Staging/Infeed/Transfer & Panel Rake Feeding System: 10' (120") Long, powered 3-chain staging conveyor; (2) units can be preloaded while (1) unit is in process. Automatic up-indexing 4,500 Lbs capacity Scissors Lift with auto. rake infeed system: infeed rake system designed with a thin material device that can automatically load material as thin a 1/8". -- Pos. # 2: LHI "72": 72" Arbor length designed for panels up to max. of 5' (60") wide, min. panel length 30"; 40 HP main arbor motor; 1/8" min. - 1" max. material thickness with no adjustment needed over a 3/8" thickness variation. 2-3/4" Dia. arbor with 1-15/16" "Fafnir" arbor bearings; positive non-marking steel contact feed rollers with (optional) poly-covering, driven from top & bottom. Includes: (6) blade collars; (2) 6" dia. vertical dust outlets with an easy access strip separator box. -- Pos. # 3: LHI Cross-Transfer System: Transfer conveyor with panel hold-down & chain drive system to change direction 90° & automatically feed LHI 102". -- Pos. # 4: LHI "102": 102" Arbor length designed for panels up to max. 8' (96") long; 30 HP main arbor motor; 1/8" min. - 1" max. material thickness with no adjustment needed over a 3/8" thickness variation; 2-3/4" dia. arbor with 1-15/16" "Fafnir" arbor bearings. Positive non-marking steel contact feed rollers with (optional) poly-covering, driven from top & bottom. Includes: (6) blade collars; (2) 6" dia vertical dust outlets with an easy access strip separator box. -- Pos. # 5: LHI Stacking & Outfeed Transfer System: Auto. down-indexing 4,500 Lbs cap. Scissor Lift; (4) adjustable alignment posts & (4) bin separators to keep processed stacks square. 98' (96") Long outfeed gravity conveyor.Operating System: -- (1) LHI ALLEN-BRADLEY "Inter-Link" PLC for simple single-operator management of the entire system from (1) central control.NOTE: ...Attached description & pictures are for INFO purposes only; ...a NEW System can be modified to your exact specifications!NOTE: PRICING DOES NOT REFLECT FACTORY'S 10% MATERIALS SURCHARGE

LHI RFPR-72/10 MULTI-BLADE PANEL SAW: Specifications: -- 40 HP main arbor motor; 1/8" min. - 1-1/4" max. material thickness; 10" dia blade with 1.25" minimum spacing between the blades; -- 3-15/16" Dia. arbor with 72" of usable width cutting capacity, min. panel length 30"; -- 1-15/16" precision arbor bearings; positive powered steel contact feed rollers; -- Fixed feed speed of 80 FPM. Blades & collars: -- Thin kerf 10" dia x 40-tooth x 4.18" bore non-split blades with quick & easy setup for fast blade positioning/removal (blades not included). -- Blades & collars are sold separately & not included in the machine price; 10" dia. x 40-tooth thin kerf blades, please add ...$ 105 ea.;1.25" wide x 4.18" bore blade collars, add ...$ 145 each. Complete with: -- (2) 4" dia dust collection ports on top and (1) 8" dust collection port on bottom. Total recommended 2,200 CFM -- Actual Model is LHI RFPR-72/10 Roll Feed Panel Saw. Available Options at additional cost: -- 110 V Infeed Scissor Lift with foot pedal controls or automatic up-indexing; 110 V Outfeed Scissor Lift with automatic down-indexing;Assortment of blade thicknesses & diameters; Split blade & collar system; Additional Options Depending on application: -- Main motor power from 30 - 75 HP; 4" Max. cutting height (requires 75 HP motor); -- Variable feed speed; Non-marking Polyurethane contact feed rollers; -- Additional arbors; "QUICK CHANGE" arbor system (see video); -- "Pigtail" quick change Crosscut Saw System.Many more tooling & configuration options available upon requestThis machine will cut a bundle (42 sheets) of 3/4" Plywood. PB, MDF or OSB into narrow strips in (4) minutes or less.NOTE: PRICING DOES NOT REFLECT FACTORY'S 7% MATERIALS SURCHARGE

LHI RFPR 102/10 MULTI-BLADE PANEL SAW: with 102" of usable width cutting capacity. Specifications: -- (1) 40 HP main arbor motor for 1/8" min. - 4-1/4" max. material thickness; min. panel length 30"; 102" of usable width cutting capacity. -- 12" Dia max. blade capacity; 1.25" minimum spacing between the blades; -- 3-15/16" Dia. arbor with 1-15/16" precision arbor bearings; -- Positive powered steel contact feed rollers with (8) Polyurethane drive rollers; fixed feed speed of 80 FPM. -- Includes (6) arbor collars - blades not included. -- Complete with:(2) 4" dia dust collection ports on top and (1) 8" dust collection port on bottom. Total recommended 2,200 CFM.Available Options: -- Blade Box & "Quick Change" Arbor Cart and Trolley $12,590.00 each -- Arbor Carts modifications to accept 12" dia. blades $700.00 each -- Single Point Height Adjustment $ 6,000.00 each -- "Quick Change" set up kit (includes belt guide, belt tensioner, and hydraulic arbor lock) $3,695.00 each -- Tandem 8000# capacity infeed Scissors Lift, 2 HP, 3 Phase, 230/460 Volt, 31" x 192" platform and cross bars for fork truck entry $14,495.00 each -- Tandem 8000# capacity outfeed Scissors Lift, 2 HP, 3 Phase, 230/460 Volt with 48" x 192" platform and beveled crossbars for fork truck entry and auto down indexing $16,390.00 each -- Drag Chain Feeder Conveyor - Roller conveyor transfers sheets to in-feed of saw and dog chains align and start the sheets into the saw feed rolls. Recommended with 102" wide machines, $18,800 Tooling Cost: -- Carbide Tip Blades 10" dia. x 40-tooth thin kerf blades $125.00 each -- Saw Blade Tooling Collars $125.00 eachOn average this machine will cut a bundle (42 sheets) of 3/4" Plywood. LVL, PB, MDF or OSB into narrow strips in 4 minutes or less.NOTE: PRICING DOES NOT REFLECT FACTORY'S 10% MATERIALS SURCHARGE

LHI 4,500 # Scissor LiftSimple Design, Low Cost, High Performance w/ Off-The-Shelf Parts so you can keep it running years from now Specification: -- 4,500 Lbs weight capacity. -- 48" x 96" Smooth steel platform. -- Lowered height 9-1/2" raised height 49". -- Travel speed: 1/2" per second up -- Foot pedal control.Available Options: -- Automatic Down Indexing -- Automatic Up Indexing -- Automatic Up/Down Indexing