
704-841-2001
Backed with a massive machinery database considered to be “the blue book” of woodworking machinery), EX-FACTORY Auctions provides a complete assessment of your equipment and allows you to interact with the market real-time in our dynamic Online Auction!
Industry
Woodworking
1910 Results Found

704-841-2001
CANTEK RAPIDEDGE PRO EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications:0.4 - 3 mm Edge thickness; strip material can be hand fed; panel thickness 0.315" - 1.77" (8 - 45 mm); min. panel length 6.7" (170 mm); min. panel width 3.54" (90 mm). 0.4 kW Heated infeed fence for better glue adhesion; 2 HP (1.5 kW) feed motor with fixed feed speed of 29 FPM (9 MPM).Equipped with: -- Pre-mill Unit:(2) 2 HP (1.5 kW) - 12,000 RPM each counter rotating cutter-heads for removing up to 3 mm of the panel edge. -- Glue System:Quick-Change 1.2 kG Teflon coated glue pot is designed for EVA hot melt glue. The glue pot is a Quick-Change type and can be removed and replaced in less than (1) minute.Spring-loaded Pressure Unit with (2) pressure rollers.The Guillotine shear can rough trim coiled material up to 3 mm in thickness. Pressure rollers section consists of : (1) Large driven roller followed by a smaller one. Workstations: -- End Trim: (1) 0.29 HP (0.22 kW) - 12,000 RPM Single motor end trim system with (2) saw blades; unit is mounted on high precision linear guide rails. -- Rapid Top & Bottom Trim:The RAPID adjustment system uses a pneumatic 3-position adjustment to quickly change from 0.5 mm to 1 mm, to 2 mm edgebanding. This is done directly from the Control Panel.(2) 0.5 HP (0.37 kW) - 12,000 RPM high frequency motors for Top & Bottom trimming of the panel; each motor has an inset knife cutter head that can be adjusted from flush to beveled finish for thin edges and radius trimming (2 mm radius). -- Nesting Function:Nesting kits are installed on the Top & Bottom trimmers and scraping units to ensure they properly trace the panel when predrilled for hinge holes. -- Corner Rounding:(1) 0.5 HP (0.37 kW) - 12,000 RPM, high frequency single motor Corner Rounding Unit. Quick change corner rounding motor for fast changeover from 1 mm to 2 mm radius on the ends.Unit can process between 0.4 - 3 mm and up to a board thickness of 1.77" (45 mm).The multifunctional cutter can round straight or radius edges with a 2 mm radius cutter. -- Profile Scrappers:Multi-radius scrapers allow operator to apply a 1 mm or 2 mm radius on the Top & Bottom of the panel. -- Flat Scrappers:Flat insert knives designed to remove any excess glue which remains on the surface of the panel after applying the edge due to squeeze out. -- Buffing Units:(2) 0.2 HP (0.12 kW) - 3,000 RPM motors, Top & Bottom Buffing units leave a super finish on ABS & PVC edging and removes any discoloration on the edges. -- Release Agent Spray Unit:Applies release agent to the Top & Bottom surface of the panel before applying the glue allows for simple removal of any excess glue.The unit is located before the Pre-milling Station so any overspray which gets on the edge will be milled off to ensure proper bonding. -- Cleaning Agent Spray Unit:The Cleaning Agent System sprays the Top & Bottom edge before the Buffing Unit & designed to polish the edge and loosen any excess glue residue on the surface
$3,150
Non-Oscillating Edge Sander with end sanding kit. -- 6" Wide x 108" long belt. -- 6" x 40" Graphite covered platen. -- 1 HP -1.5 HP, or 3 HP -2 HP, 3-Phase motor w/magnetic switch. -- 7" Diameter drive pulley. -- 7-3/4" x 37" Front table with a 6" vertical adjustment. -- End table for radius work with a 6" vertical adjustment. -- Heavy laminated tables, fabricated steel base and swing-away dust hood.
$11,200
CANTEK - SS512TB Tilting Spindle ShaperSpecifications: --Tilting spindle from -5° to +45° and 6" x 43" fence. --1-1/4" interchangeable spindle is standard (other sizes available). -- Large cast-iron table is ground and polished for maximum stability and durability. -- Powerful 7.5 HP motor for even the most demanding profiling work. -- Five spindle speeds can be easily adjusted to suit your tool diameter. -- 5-1/2" Useable spindle length, above table 13-¼"; below table 8-¼". -- Electronic spindle brake for added safety and facilitates fast changeover. -- Precision fence assembly with micro-infeed and outfeed fence adjustment. -- The finger-style fence allows the fence to be adjusted around the cutter for added safety and workpiece stability. -- Table size 31 ½"; x 39.4″. -- Dust port (1) 5″ on guard, (1) 4" into the table.
Call for Price
This item is in an Auction on exfactoryauctions.com. Go here to view item: http://exf.ac/i6k ROCKWELL/CRESCENT 5-Head Single Head Tenoner Equipped with: Manually-operated sliding table. (1) Top & (1) Bottom Tenon Heads, Each with 2 HP Motor, (1) Top & (1) Bottom Cope Heads, Each with 1 HP Motor, & (1) 7" Cutoff head with 1 HP Motor.
$1,695
CROUCH - 81-70 ...Edge Sander (Non-Oscillating)5 HP Direct drive motor; 6" x 144" abrasive belt size; (1) 8" x 56" Platen.Equipped with: -- (1) 12" x 56" Adjustable side table and (1) 15" x 28" end table.Tables adjust vertically 5" and laterally 2-1/2". -- 8" Dia. rubber covered drive pulley and 4" dia. aluminum idle pulley.
Call for Price
CUMMINS - 682-FDR-036JJW, ...1000K DIESEL GENERATORSpecifications: -- Output: 480/277 / 3-Phase -- 1,000 kW -- 1,250 KVA -- 1,504 Amps -- 1,800 RPMNOTE: (299) Hours on meter in factory-built enclosure. - Available for inspection!
CURTIS - 5E2VT8-A3, ...Air Compressor, 5 HPSpecifications: -- Maximum allowable working pressure of 200 at 450 PSI.Equipped with: -- 80-Gallon Tank
Call for Price
THIS IS DESCRIPTION FOR Model: RSB-30T PLACE HOLDER ONLY...............Open Type- No Enclosure460Volt 3-PhaseBelt DriveFixed SpeedCapacity(cfm): 135cfm @100 psi; 125cfm @ 125 psi; 113cfm @ 150 psi; 101cfm @ 175 psiMotor: 30HPTank: 120 gal.Dimensions(inches): 77Lx41Wx69HWeight: 1420 lbs.Rotary Screw Air Compressor Key Features:LOW POWER CONSUMPTIONOPTIMAL COMPONENT SELECTION FOR MAXIMUM PERFORMANCE IN THE TOUGHEST APPLICATIONSSMART CONTROL OPTIONS FOR POWER SAVINGS IN ALL CONDITIONSHIGHLY EFFICIENT AIR ENDS WITH EPACT EFFICIENCY MOTORS FOR LOW POWER CONSUMPTIONEASY AND OPEN ACCESS TO SERVICE POINTSSTANDARD AND LONG LIFE COMPONENTS REQUIRE MINIMUM SERVICERUGGED AND LEAK FREE DESIGN FOR REDUCED MAINTENANCE COSTS HIGH PERFORMANCEPRECISION ENGINEERED COMPONENT SIZING FOR MAXIMUM PERFORMANCEHIGH EFFICIENCY FILTRATION AND SEPARATION FOR MAXIMUM FLOW AND DURABILITYLARGE AND SLOW SPEED AIR END FOR HIGH PERFORMANCE AND EXTENDED SERVICE LIFEStandard FeaturesINTAKE FILTER (HEAVY DUTY), HIGH EFFICIENCY AIR END, LOW LOSS DRIVE SYSTEM, EPACT EFFICIENCY ELECTRIC MOTOR, ACROSS THE LINE STARTER, ON-LINE/OFF-LINE WITH MODULATION, TIMED DUAL CONTROL, 115V CONTROL VOLTAGE, MULTI-STAGE OIL SEPARATION SYSTEM WITH OIL SUMP TANK, HEAVY-DUTY OIL FILTER WITH BY-PASS, OIL LEVEL SIGHT GLASS.
Call for Price
D M C FINESAND 130 2PO WIDE BELT (50" - 90", 2-HEAD): -- Specifications:Orbital Pad Sander, designed for cross-grain scratch removal on style & rail frames; with (2) Orbital Platens & (1) Brush. -- Working Capacity: Width 51", height/opening 1/8" - 4-5/8", motorized part thickness adjustment with digital readout, (4) screw jacks rise & fall. -- Sanding Heads: (2) 10" Wide Platen heads with rubber surface for elimination of abrasive belt cross-grain scratches. Dual orbital action heads with (1) high speed orbit on sanding pad, powered by 5.5 HP motor, and a secondary "low RPM" orbit on head assembly (1.5 HP motor), superimposed over the high-speed orbit for fast cutting action. -- Rotating Cleaning brush on outfeed side. Abrasive material for Sanding Heads is 18" x 52" in size. -- Feed Conveyor: Variable feed speed from 6 - 40 FPM, inverter controlled by 5.5 HP motor; vacuum conveyor bed with 15 HP blower motor. -- Complete With: - Digital height readout. - Infeed and outfeed rubber coated hold-down rolls. - Infeed hand safety stop bar, emergency e-stop. - Star-Delta motor starter. - (2) Dial indicator motor load meters.
$109,500
DMC UNISAND K (3) Bottom and (3)Top heads wide belt sander. --, 43" max. width. - Bottom Head sequence : 1st Head Contact roll, approx.18.5 KW motor- 2nd Bottom Head Contact roll, 2rd Bottom head, Combination head with roll and platen , approx.15 KW 2-speed motor, belt speed 118 m/sec. -- Bottom panel brush. -- Top Heads: 1st Top Head: Rubber covered contact roll approx. 18.5 KW motor, 2 speed, belt speed 9/18 M/Sec. adjustable contact roll with pneumatic grit adjustment. 2nd and 3rd Top Head: Combination head with Rubber covered contact roll and polishing platen, approx. 18.5 KW HP motor, adjustable contact roll with pneumatic grit adjustment.Top panel brush. -- 44"x 103" abrasive belts with electronic tracking; computer controlled set-up functions with key pad and LCD screen. -- Vacuum Conveyor feed belt with variable feed speed from 11 - 60 FPM, approx. 7.5 KW HP feed drive, automatic conveyor belt tensioning & tracking. -- Infeed & outfeed holddown pinch rolls on all heads, motorized part thickness opening with LED readout, 1/8" - 4" max opening, automatic part thickness set-up sensor. -- Complete with: Infeed safety stop, outfeed emergency stop, motor load meters, high efficiency dust extraction and control console with monitor. -- Actual model USK1350-IM3 + USK1350
DMC - UNISAND 2000-M2, ...Wide Belt Sander (2) Heads -- 53" Width cap. Drum, Platen.Head Configuration: --1st Head: 11" dia. (300 mm) Rubber-Covered Contac; (2) speeds or inverter adjustable 20 - 25 HP; Varied RPM. --2nd Head: Combination head with drum and graphite covered 2-1/2" finishing platen; 25 HP.Specifications: -- 54"x 103" Abrasive belts with electronic tracking. -- Shoe & Roller Holddowns. -- "Hydra 35" Computor controlled; set-up functions with keypad and LCD screen. -- Conveyor belt feed with variable feed speed from 11 - 60 FPM; 6.4 HP feed drive. -- Vacuum conveyor bed with: 7.5 HP Motor and suction fan. -- Automatic conveyor belt tensioning & tracking. -- Motorized part thickness opening with: LED Readout; 1/8" - 4" max. opening; automatic part thickness set-up sensor. Equipped with & Features: -- Infeed safety stop, outfeed emergency stop, motor load meters.2-Roll infeed conveyor extension; high efficiency dust extraction.
$94,500
DMC - EuroSystem SY-TC 1350, ...Heavy-Duty 4-Head Wide Belt Sander53" Width cap. Drum, Drum, and Drum; Segmented Platen.Specification; -- Max. workpiece width: 53". -- Workpiece thickness: 0.32" - 6.8".Head Configuration & Feed: -- 1st Sanding Unit: 10"; Diameter grooved steel contact drum; 60 HP motor. -- 2nd Sanding Unit: 10"; Grooved rubber covered drum, 27 HP motor. -- 3rd Sanding Unit: 10"; Grooved rubber covered drum; 20 HP Motor. -- 4th Sanding Unit: Electronic segmented platen; 35 HP motor. -- Belt size of 53" x 103". -- Feed Motor: 5 HP, Variable feed speed. -- Vacuum Bed. -- Constant Pass Line.Equipped with & Features: -- Power Panel Touchscreen Control. -- Shoe type holddowns. -- Amp meters for all Sanding Units.
$21,500
DMC - 1350 RK, ...TECHNOSAND Dual Head Wide Belt Sander.(2) Heads, 52" width cap. - Head sequence: Contact sanding roll and Segmented platen. Head Configuration:1st Head: 7" (175 mm) Dia., 85 durometer rubber-covered calibrating contact sanding roll.2nd Head: Segmented finishing platen with EPICS (sectional electronic pad) with (46) electronically controlled air segments.Specifications: -- 53" x 103" Long abrasive belts with electronic tracking on all wide belt heads. -- Turbo panel blowers, timed abrasive belt air cleaners. -- DMC "Hydra 35" control, "EPICS" control for sectional platens. -- (99) Programs; graphic screen for machine configuration, +/- control on segmented platens, abrasive belt cleaners. -- Sequential automatic start-up, machine troubleshooting and self-diagnosis. -- Variable feed speed from 15 - 60 FPM (4.5 - 18 MPM), 1.5 HP feed drive, vacuum conveyor bed with 7.5 HP suction fan and motor.Equipped with & Features: -- Automatic conveyor belt tracking, infeed & outfeed holddown pinch rolls or shoes on all heads. -- 0" - 4" Motorized programmable thickness adjustment with LED readout. -- Automatic part thickness adjustment, infeed hand safety stop, outfeed emergency stop. -- Motor load meters and control console with monitor & keypad.NOTE: Message from the Seller: The machine was setup by a DMC tech. It has a new calibration roller & new bearings, rebuilt HYDRA 35 controller; currently under power, comes with dust collecting manifold and hoses, plus the machine can be loaded onto a flatbed for ...$ 600.
$27,500
D M C - UNISAND 135, ...3-Head Wide Belt Veneer & Finishing Sander. -- General Data:3-Head, 51" (1,300 mm) nominal width cap.; motorized part thickness opening with LED readout; 1/8" to 4" max. - Head sequence: Cross belt, rubber-covered Drum, Pad. Head Configuration/Specs: -- 1st Head: Cross belt with: EPICS 44 Segmented electronically controlled air platen; 2-speed abrasive belt; approx. 36/72 FPM (11/22 MPS) linear speed; driven by 19 & 24 HP motors; 6" wide x 238" (6,050 mm) long abrasive belt. Inside synchronized Chevron belt, approx. 228" (5,800 mm) long.Pad unit with pneumatic cylinders: Each acting on a high absorption felt strip; working pressure controlled via control panel. HYDRA Belt: 2' Electronic control with oscillating blower for cleaning. -- 2nd Head: Rubber-covered 45-durometer steel roll, 9.8" (250 mm) dia. with: 18 HP 2-speed motor, 52" x 103" (4,055 mm) long oscillating abrasive belt with electronic tracking; air blast abrasive belt cleaner. Belt runs approx. 3,550 FPM (18 MPS) linear speed; adjustment & indicator of working position. -- 3rd Head: Flexible Sanding Platen with: EPICS 44 Segmented electronically controlled air platens; 3-speed 24 HP motors; 52" x 103" (4,055 MM) long abrasive oscillating belt with electronic tracking, timed oscillating air blast abrasive belt cleaner.Pad unit composed of: Pneumatic cylinders, each acting on a high absorption felt strip. Working pressure controlled vial control panel. Special rails allowing a quick change of graphite cloth on pad. Interchangeable system to modify the hardness, stiffness, and profile of the contact surface. Controller: -- DMC "HYDRA 30" Upgraded computer with: Working position display modes mounted in a separate control cabinet; automatic thickness device reads and adjusts feet table height, motor load meters. Transport Belt Drive: -- Variable feed speed of 16 to 82 FPM, conveyor feed drive, infeed & outfeed holddown pinch rolls on all heads; infeed hand safety stop, outfeed emergency stop; high efficiency dust extraction and separate control console with monitor, keypad, etc. Also included: -- Cleaning brush head at machine discharge. -- High pressure vacuum blower. -- Dust manifold. -- Extended outfeed table.
SCM DMC 90 RCS 135 2 Head 53 inch Wide Belt Sander 53" Width cap, Steel Drum, Combination HeadHead configuration1st Head: Steel Drum 36 HP Motor, 9" Diameter 2nd Head: Combination head 65 shore drum and solid wood platen, 30 HP Motor, 7" Dia. drumSpecifications: -- 54" x 103" Abrasive belts with electronic tracking. -- Shoe & Roller Holddowns. -- "Hydra 35" Computer controlled; set-up functions with a keypad and LCD screen. -- Conveyor belt feed with variable feed speed from 11 - 60 FPM; 6.4 HP feed drive. -- Vacuum conveyor bed with 7.5 HP Motor and suction fan. -- Automatic conveyor belt tensioning & tracking. -- Motorized part thickness opening with LED Readout; 1/8" - 4" max. opening; automatic part thickness set-up sensor. Equipped with & Features: -- Infeed safety stop, outfeed emergency stop, -- Motor load meters. -- 2-Roll infeed conveyor extension; -- High-efficiency dust extraction.NOTE: Specs have to be verified
$39,500
DMC UNISAND K 1100 Wide belt sander4-Head, 43" (1,100 mm) max. width cap. Head sequence: (3) Contact rolls and (1) Combi with roller and segmented platen.Heads configuration: -- 1st Head: Helical grooved steel contact roll, 10" dia., 48 HP motor. -- 2nd Head: Helically grooved rubber covered contact roll, 12-1/2" dia. and 65-Shore covering hardness, 35 HP motor. -- 3rd Head: Helically grooved rubber covered contact roll, 12-1/2" dia. 45-Shore covering hardness, 30 HP motor. -- 4th Head: Combi head with roller covered with rubber, 30 shore and Finishing sanding pad unit , 30 HP 2-speed motor with segmented pads pneumatically controlled -- All heads use 44" x 103" (to be confirmed) abrasive belts and are equipped with electronic tracking, automatic tensioning, automatic emergency breaking, and oscillating sanding belt cleaners.Controls: -- "HYDRA V-PAD" 10" Touch-screen computer for setup functions, color LCD Display, allows operator to setup/recall part thickness, -- Conveyor feed speed (3.5 - 18 MPM), -- Abrasive belt direction, and reversible speed setting of 4th head. -- Conveyor belt feed with inverter control, feed speeds from 11 - 60 FPM, 5.5 HP feed drive; -- Infeed & outfeed holddown pinch rolls on all heads, automatic part thickness setup with the moving feed belt, -- 2-speed motorized part thickness adjustment, 1/8" - 6" max. opening; -- Infeed & outfeed motorized conveyor extension rollers, automatic part thickness setup sensor. Complete with: -- Safety stop at infeed, -- Anti-kickback device, -- Infeed & outfeed emergency stops, -- Motor load meters, i -- Infeed & outfeed idle rollers, -- High efficiency dust extraction, and control console with monitor.Note: (spare parts not installed) New feed belt , new front pressure roller, new front pressure bar and several new small parts for approx $15,000 of value +11 boxes (approx 5 belts/ box) sanding belts 100 grit, 120 grit, 180 grit and 220 grit.
$45,000
DMCTC 1350-M2-RP Orbital Sander (2) Heads --53" Width cap. Drum, Combination Head --Head Configuration --1st Head:10" Dia. helical grooved rubber covered calibrating roller, 26 kw (34 HP) motor. --2nd Head: Rubber covered contact roller with finishing platen 18 kw ( 28.5 HP) motor. --Specifications --Working width 1350 mm --Max thickness 170 mm --Belt size both heads 1370 mm X 2620 mm --Feed speeds variable from 3.5 -18 m/min. Feed motor 2.2 kw ( 3 HP) motor --Equipped With --Electronic sanding belt oscillation --Exhaust hoods with 4 outlets --Motor safety switch for main motor --Power rise and fall --Panel cleaning brush --Sander dim. L 2600 mm X W 2400 mm X H 2550 mm --Weight 2900 kg. --There is a crack in the plastic housing but it does not affect the functionality of the machine.
DMC UNISAND 2000 M3 Wide Belt Sander (3) Heads53" Width cap. Drum, Combination Head, Segmented PlatenHead Configuration:1st Head: Rubber covered contact roll 9" dia. 29 KW motor2nd Head: Combination Head, contact roll with graphite platen 21.4 KW motor3rd Head: Electronic Segmented Finishing platen with (46) segmented pads 18.5 KW motor.4th Station: Panel cleaning felt type head 1.74 kW, 460V, 3-phase, plus Air Cleaning headsSpecifications: -- 54" x 103" Abrasive belts with electronic tracking -- Computer controlled setup functions with keypad and LCD screen. -- Conveyor belt feed with variable feed speed from 11 - 60 FPM, 3 HP feed drive -- Vacuum conveyor bed with 10 HP motor and suction fan -- Automatic conveyor belt tensioning & trackingEquipped with & Features: -- Infeed & outfeed holddown pinch rolls on all heads. -- Motorized part thickness opening with LED readout. -- 1/8" - 4" max opening, automatic part thickness set-up sensor. -- Infeed safety stop, outfeed emergency stop, motor load meters --High efficiency dust extraction. -- Control console with monitor.Note: Dust manifold included
$35,000
DANCKAERT - 44 , ...ResawAir Strain 44"; x 5"; Bandsaw.Features & Specifications: -- McDONOUGH Center Split Feed Works. -- Wheel is supported on both sides - not cantilevered. -- Pressured guides. -- McDONOUGH Infeed Rolls. -- Max. Cut: 14";. -- New Dynamic brake. -- 60 & 100 HP. -- Control Cabinet (has battery backup and resistors to prevent spikes). -- Infeed & outfeed systems are the same. -- 24 ft. Long Camel Back chain (has air bags that are controlled by photo cell to raise & lower and index 1-board at a time). -- Max. length of lumber: 24 ft.From Seller: "The machine has a new VFDD 100 HP and a new WEG Severe Service 60 HP motor. All new hydraulic motors, caramel back chain, and roll cases."NOTE: Needs hydraulic unit.
Call for Price
Custom-Built DEIMCO Through Feed Sprayer with a BLASDEL IR Preheat Tunnel that is available MARCH of 2023. Until then, the System can be seen in operation. -- Line was designed to preheat Fiber Cement board prior to painting and is followed by a Single-Arm Reciprocating Sprayer with 4-Spray Gun cap. Spray Guns not included.SEE ATTACHED VIDEO FOR A GOOD LOOK AT THE LINE's OPERATION!Built in 2019, the System was used for approx. (2) years; current owner changed their process and no longer requires the equipment.Oven width cap.: 60" Wide, 1-3/4" part height cap.; overall Oven dimension: 84" Wide x 12-1/2' long x 55" high, excluding the Blower & Stack. Line/Conveyor: Variable speed drive, 18.5 FPM to 26 FPM; Reciprocator operates up to 260 FPM and set by the HMI. 2-Zone Oven: -- Zone 1: (2) Upper left side wall/ceiling mounted; 18" x 60" emitters. -- Zone 2: (2) Right upper side wall/ceiling mounted 18" x 60" emitters; 8" clearance between emitters & rolls. Heaters: Natural gas using 7" WC; 480 Volt preheat; TC, FM, flange frame. - Gas Ratings: 360,000 BTUH Max. input ; 100,000 BTUH standby input; Air Exhaust on infeed & Injection Blower on outfeed. Electrical ratings: 26.6 Amps, 480 V - 3 Phase, 60 Hz.Exhaust: 980 CFM, 1 HP Motor.Control Panel: 60 AMP Disconnect switch, ALLEN-BRADLEY "Panel View Plus HM", IEC contactor & High Temp PID exhaust.NOTE: (25) New replacement conveyor rollers & (40) reconditioned rollers for IR Tunnel.DIEMCO Sprayer complete with: (1) Reciprocating Arm holds (4) guns and reads the leading & trailing edge to turn on & off the guns as the parts feed through; best to run full width loads through Sprayer; Overspray funnels into buckets.Spray Guns turn on & off based on the part leading & trailing edge; read by a light curtain on the infeed end.Dims: GFS Spray Cabin: 13' Deep x 8-1/2' wide x 9' high surround the reciprocating arm. - Filter & Exhaust Section: 13' Wide x 3' Deep x 10' High.