HOLZ-HER - 1411-3, EDGEBANDER Cartridge Glue System, 5 mm edge thickness cap. (up to 13 mm w/optional tooling), 1-3/4" max. panel thickness, and 7" min. panel length.Equipped with: -- Automatic magazine coil & strips, 3 mm PVC cap. pneumatic guillotine for coil cutoff. -- Pressure section with (1) large dia. drive roller & (1) idle. Workstations: -- Double-motor end trim model "1918" (tilting 0° - 10°), 0.5 HP - 18,000 RPM motor each. -- Top & bottom radius trim model "1942", 0.8 HP - 18,000 RPM motor each (trim motors are 0.6 kW HF). -- Top & bottom glue scraper unit "1964", with air jets for blow-off. -- Top & bottom buffing unit "1940" (tilting cap. 0 - 5°), 0.2 HP - 1,400 RPM Motors each. -- Variable feed speed from 36 - 52 FPM. - Fixed outboard panel support. Complete with: -- PLC (Programmable Logic Control) for easy setup and program storage. -- Frequency converter, sound enclosure, and used tooling..

HOLZ-HER CUT 85 FRONT LOAD, AUTOMATIC PANEL SAW: -- Specifications:4,250 mm (167") Max. rip cut cap., 3,800 mm (149") pull back pusher stroke; 97 mm (3.8") saw blade projection.15 HP (11 kW) Main saw motor, 3 HP (2.2 kW) scoring motor. -- Saw Carriage:Variable feed speed from 3 - 328 FPM (1 - 100 MPM ), return speed of 328 FPM (100 MPM).Automatic cutting length limiter adjusts the cutting length at the end of the workpiece, automatic saw carriage lubrication. -- Pusher Fence:(7) Material gripper clamps; 259 FPM (80 MPM) forward positioning speed, 259 FPM (80 MPM) return speed.Rack & pinion movement on both sides to assure the pusher remains parallel. -- Operator & Machine Control:PC Front-End with CUTCONTROL "Direct Cut" + "OPTIPRO" + Windows 2000 operating system,15" TFT Display with unlimited program storage via floppy disk, keypad for data entry, USB & RS-232 serial port, CD ROM & 1.44 MB disk drive for additional storage of programs.CUTCONTROL offers Real-Time Graphics, diagnostic for errors or machine malfunction by means of an error signal code, incremental or absolute programming in mm or inches."Direct Cut" allows the operator to easily input information for absolute, serial, format, grooves, perforations, & position cutting which allows the machine to easily adapt to various situations & materials."OPTIPRO" is a very user friendly on-board Optimizing System for all types of various cutting patterns, including angled cutting. -- Complete with: Rear roller support rails; automatic crosscut side aligner; automatic saw blade height adjustment.(3) Air support tables, ea. 78" x 24" (1,981 x 509 mm). -- Actual Model is HOLZ-HER CUT 85 4300.

HOLZ-HER CUT 6120 FRONT LOAD, AUTOMATIC PANEL SAW: -- Specifications: 3,900 mm (153.5") Max. rip cut cap., 3,900 mm (153.5") pull back pusher stroke; 82 mm (3.2") saw blade projection.15 HP (11 kW) Main saw motor, 1.5 HP (1.1 kW) scoring motor. -- Saw Carriage:Variable feed speed from 3 - 320 FPM (1 - 100 MPM ), return speed of 416 FPM (130 MPM).Motorized bi-directional grooving capabilities with electronic adjustment for 0 mm - 35 mm.Automatic cutting length limiter adjusts the cutting height & cutting length at the end of the workpiece. -- Pusher Fence:(7) Material gripper clamps, (1) Double Finger mounted at the cross-cut fence location for narrow strip cutting & (6) standard clamps. 82 FPM (25 MPM) forward positioning speed, 328 FPM (100 MPM) return speed.Variable pressure settings for delicate materials. Pressure beam has an integrated "Last Cut" operation to achieve a "0" mm panel dimension.Rack & pinion movement on both sides to assure the pusher remains parallel. -- Operator & Machine Control:PC Front-End with "CUTCONTROL 2" + "EASY-PLAN" + Windows operating system,19" TFT Display with unlimited program storage; keypad for data entry, USB & RS-232 serial port, "CUTCONTROL 2" offers Real-Time 3D Moving Graphics, diagnostic for errors or machine malfunction by means of an error signal code, incremental or absolute programming in mm or inches."CUTCONTROL 2" allows the operator to easily input information for absolute, serial, format, grooves, perforations, & position cutting which allows the machine to easily adapt to various situations & materials."Opti-Cut" & "EASY-PLAN" is a very user friendly on-board Optimizing System for all types of various cutting patterns, including angled cutting -- Complete with: Non-Marking rear roller support rails: Solid Air Cushion Table before & after the cutting line, ensures easy panel handling. Pneumatic crosscut side aligner, adjustable from 0" - 82.6" (0 - 2,100 mm). Side aligner is "Fully Automatic" adjustment when panel is less than 1,300 mm (51")"Quick Change" Blade system with automatic saw blade height adjustment; Electronic positioning of the scoring blade through the NC control.(3) Adjustable via "pneumatic locking" air support tables, ea. 70.8" x 23.6" (1,800 x 600 mm); -- Actual Model is HOLZ-HER CUT 6120 Dynamic

HOLZ-HER - 1619, ...Boring Machine (Construction & Line Boring) -- Specifications:(19) Spindles on 32 mm centers; bores vertically from top and horizontally from the rear; repositions via manual air shock assisted tilting.2 HP Motor with: 2,800 RPM Gear driven boring head. -- Features:4-Position turret style depth stop for boring depth and a 4-3/4" max. stroke of boring head.24-3/4" Working width; 27-1/8" max. panel width; 19-1/2"; x 38"; x 32-1/2"; H table size. -- Equipped & Complete with:RH & LH Indexing fence with flip stops; (2) indexing pins (for continuous line boring); (3) 4" dia. pneumatic holddown clamps; foot pedal actuator; magnetic push button starter. -- Actual Model is: HOLZ-HER 1619Dimensions of this specific machine with pallet: 52" x 40" x 65" H.Dimensions of this specific machine when vertical: 52" x 37" x 60" H.Dimensions of this specific machine when horizontal: 52" x 51" x 46" H.

HOLZ-HER 1402 HF Compact EdgebanderFeatures: -- Cartridge glue system, 3 mm edge thickness cap., -- Semi-automatic feed magazine, coil stock feeds automatically with guillotine cutoff, all strip stock is fed manually with pusher bar to advance the edging. Digital glue height indicator.Workstations: -- Double motor end trim (1 HP - 10,500 RPM motor ea.) -- Universal top & bottom fine trim (1942M) for bevels from 0° - 15³; allows simultaneous bevel & profile trimming (1 HP - 18,000 RPM motor ea.; trim motors are 0.6 kW HF - 300 Cy). -- Top & bottom PVC scraper unit (1929) for 0.8 - 3 mm radius. -- Top & bottom buffing (1940), 0.3 HP - 1,620 RPM motor ea. -- Single feed speed of 35 FPM. -- Complete with: Fixed outboard panel support, frequency converter, sound enclosure, and used tooling.

HOLZ-HER 1435-SE EDGEBANDERCartridge glue system, 5 mm edge thickness cap. (up to 8 mm w/optional tooling), automatic magazine coil & strips, 3 mm PVC cap. pneumatic guillotine for coil cutoff.Workstations: -- Double motor end trim (2) 0.3 HP - 9,000 RPM motor ea.), chamfers 0° - 10° -- Universal top & bottom fine trim (for bevels from 0° - 15°) allows simultaneous bevel & profile trimming, (2) 0.8 HP - 18,000 RPM motor each; all trim motors are 0.6 kW HF - 300 Cy. -- Top & bottom PVC scraper unit for 0.8 - 5 mm radius, with air jets for blowoff. -- Top & bottom "jump" buffing (0.3 HP - 1,620 RPM ea.). -- Single feed speed 35 FPM. --Complete with: --Built-in operator control panel, outboard panel support, frequency converter, used tooling, and sound enclosure.

HOLZ-HER - 1432, ...CP/B Edgebander (Compact) -- Cartridge glue system (single cartridge system); edge thickness cap.: 0.3 to 3 mm (1/8"); max. banding height: 2"; min. panel width: 60 mm; min. length: 180 mm.Equipped with: -- Semiautomatic feed magazine; coil stock feeds automatically with guillotine cutoff; all strip stock is fed manually with pusher bar to advance the edging.Workstations: -- Single motor end trim for leading & trailing edge (trim motor recently replaced). -- Top & bottom flush/bevel trim: 1 HP - 28,000 RPM Motor ea. (recently replaced with BOSCH Trimmer motors). -- Top & Bottom buffing unit: 0.3 HP - 1,620 RPM ea. motor; equipped with: Cotton flap wheels. -- Single feed speed: 16-1/2 FPM.Complete with: -- Sound/safety enclosure; outboard panel support. - Machine is on casters.

HOLZ-HER - 1435-SE EDGEBANDER"1906" Cartridge Glue System; 5 mm edge thickness cap. (up to 8 mm w/optional tooling); automatic magazine coil & strips; 3 mm PVC cap. pneumatic guillotine for coil cutoff. Workstations: -- Double-motor end trim, (2) 0.3 HP - 9,000 RPM motor ea.; chamfers 0° - 10°. -- Universal top & bottom fine trim (for bevels from 0° - 15°); allows simultaneous bevel & profile trimming; (2) 0.8 HP - 18,000 RPM motor ea.; all trim motors are 0.6 kW HF - 300 Cy. -- Top & Bottom PVC scraper unit for 0.8 - 5 mm radius; air jets for blowoff. -- Top & Bottom "jump" buffing (0.3 HP - 1,620 RPM ea.). -- Single feed speed: 35 FPM.Complete with: Built-in Operator Control Panel; outboard panel support; frequency converter; used tooling; and sound enclosure.

HOLZMA HPP-11-32 OPTIMAT FRONT LOAD PANEL SAW:Specifications & features: 3,200 mm (126") Cutting length & pull-back behind the cutting line; 125 mm (4.9") saw blade projection; 30 HP (22.3 kW) main & 3 HP (2.2 kW) scoring motor. -- Variable saw carriage travel speed from 0 - 410 FPM (0 - 125 MPM), constant return of 410 FPM (125 MPM). -- Equipped with: Main blade 18" (450 mm) dia. and scoring blade 8" (200 mm dia.). -- Electronically controlled overhead pusher fence, rack & pinion drive on both sides by AC Servo motor; forward speed from 0 - 262 FPM (0 - 80 MPM), return speed of 262 FPM (80 MPM); equipped with (8) gripper clamps (open up to 4.7"). -- HOLZMA CADmatic Operating system; 15" color monitor (displays cutting dimensions); data input by keyboard or 1.44 MB floppy disk drive & downloading from office PC is possible. -- Control panel mounted on double swiveling arm for ergonomic positioning by the operator. -- Includes: Combi-rollers rear machine table with profile rails, rollers spaced at 50 mm centers; front with (3) air floatation tables, 85" x 26" (2,159 x 660 mm) each. -- Complete with: Angular square fence, automatic side aligner for crosscutting, (2) aligning devices on program fence; "Quick Saw Changing System" for main & scoring blade.

HOLZMA PROFIMAT HPL 500 38/16 REAR LOAD, AUTOMATIC PANEL SAW: -- Specifications: 149.6" (3,800 mm) Cutting length & pull-back; 6.7" (170 mm) max. main blade projection; 40 HP (29.8 kW) Main & 3 HP (2.2 kW) scoring motor. -- Saw carriage: Infinitely variable speed from 0 - 492 FPM (0 - 150 MPM), constant return of 492 FPM (150 MPM).Carriage is electronically & automatically controlled (cutting height & length) through the CADmatic according to the material/program being processed."Power-Loc" quick change system for fast and easy saw blade change.NC Controlled scoring saw adjustment from the control panel during operation -- Pusher Fence:Rack & pinion digital drives with AC Servos on both sides, forward speed 295 FPM (90 MPM), return speed 295 FPM (90 MPM).(7) Material clamps which open up to 6.7" (170 mm): (3) Standard clamps with two fingers & (4) clamps with one finger.(4) Trimming rakes for thin strips/scrap removal are attached at the clamps. -- Operator Interface:HOLZMA "Power Touch Control" IPC multi-tasking controller with Windows "7 PRO" + "CADmatic 4.0 PRACTIVE" operating system;Intel i5 Dual-core Processor, Intel HD graphics card, 4GB RAM, SATA 2-250GB hard drive, (6) USB ports, (1) serial port, ATI/DVI video port, Standard industrial keyboard connection,21.5" LCD "Touch-Screen" monitor with real-time moving 2D & 3D graphics (displays cutting dimensions & error diagnostic); virtually unlimited cutting dimension memory.(2) Ethernet 10/100 interface connections; downloading from office PC is possible. -- Rear of machine: Profile rails & "Combi-rollers" at 50 mm centers; (2) integrated front & cross-aligning units before cutting to prevent off-set panels within the same book. -- Front of machine: (3) Air flotation tables 85" x 31.5" (2,160 x 800 mm) with (1) central blower unit. -- Rear Lift Table:7-Ton (14,000 LBS), 4-Column electro-hydraulic powered rear lift table running lengthwise with fork cut-outs, 150" x 63" (3,800 x 1,600 mm) capacity. Powered rollers are 4.2" (107 mm) dia x 7.79" (198 mm) spacing, 39 FPM (12 MPM) infeed/outfeed speed; Feeding material from (3) sides is possible with additional roller conveyors.22" (560 mm) Max. bunk height from floor level; 30.7" (780 mm) max. bunk height with a pit or risers; -- Complete With: Holzma's Unique "EcoPlus" System offers energy savings up to 20%; Includes Standby button & IE3 energy efficiency Motors rating.Angular cross-cut fence; Automatic side pressure device integrated into the saw carriage for cross-cutting, the machine cuts left to right to the cross-cut fence.Front & rear forks electronically & automatically controlled through the CADmatic according to the material/program being processed.Min. side aligning dimension 0" (0 mm), max. side aligning dimension 149" (3,800 mm)."Power-Loc" quick blade change system for main/scoring blades. -- Options Include: (1) Non-Powered in/out-feed staging conveyor with fork cut-outs as pictured. Micro In-feed for thin an

HOMAG SAWTEQ B-400 PROFILINE 32/32 FRONT LOAD AUTOMATIC PANEL SAW: -- Specifications:Working Capacity: 122'' (3,100 mm) Rip cutting capacity; 122'' (3,100 mm) Pull back capacity. Main saw blade projection 4.3'' (110 mm) 25 HP (18.6 kW) Main saw blade & 3 HP (2.2 kW) "Post Forming" (Jump) scoring blade; Scoring saw adjustment via "CADmatic" control. -- Saw CarriageForward speed 0 - 492 FPM (0 - 150 MPM) Saw carriage reverse speed 0 - 492 FPM (0 - 150 MPM). -- Pusher Fence:Electronically controlled overhead program fence with (9) 2-finger gripper clamps; clamps open up to 110 mm (4.3").Rack & Pinion drive on both sides, forward speed up to 296 FPM (90 MPM), return speed of 296 FPM (90 MPM). -- Operator & Machine Control:HOMAG "powerTouch2" PC Front-End with "CADmatic 5.0" Operating System "designed for industrial environments"; virtually unlimited cutting dimensions memory.21" Full HD widescreen "Touch-Screen" monitor with multi-touch display, online operation from an office PC is possible. All mounted into dust sealed, air-conditioned control cabinet."Real-Time" Cutting sequences with a new 3D assistance graphic supports the operator and is intuitive to operate, which shortens the training period and reduces errors to a minimum. This results in efficient processes and steady output.Simple handling via tapping and swiping (touch functions) with Quick change between the individual sectionsCADmatic 5.0 is Tapio compatible & open for communication with other machines and software solutions.The SAWTEQ B-400 "IntelliDivide" optimizing software is Tapio-ready from installed software or directly from the tapio cloud, allowing "IntelliDivide" to recognize the machine configuration of your saw and consider it for every optimization run in the cloud, completely automatically & you have the choice -- Complete with:On-Board Optimizer; Automatic "CENTRIC" side aligner with front & rear forks holding ripped strips squarely against the right-angle fence.Max. Side aligner stroke 122'' (3,100mm): Rear support rails with non-marking roller modules.(3) Front air flotation tables 74" x 26 (1,879 mm x 660 mm). -- Options Include:(1) American M-1202-30, 6,000 Lbs. scissor-lift, as pictured. -- Actual model is HOMAG SAWTEQ B-400 PROFILINE 32/32 US Addition.

HOMAG AMBITION 2262 (KAL 210) PRODUCTION EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications:Working Capacity: Coiled stock min/max Edge thickness 0.4 - 3 mm (0.016. - 0.118"), Strip material min/max Edge Thickness 0.4 - 6 mm (0.16 - 0.234"). -- Panel stock min/max thickness12 - 40 mm (0.472" - 1.574"). Panel Over-Hang 30 mm (1.18"). -- In-feed Fence: Adjustable in-feed fence with manual digital indicator positioning. -- Pre-Milling Station: Two3.0 kW(4.0 HP), 150 Hz, 9,000 RPM Motors; equipped with trimming column,(2) horizontal and cross slides with spindle adjustment, electro-pneumatic horizontal jump movement of the first motor; includes electronic frequency inverter for control of motor speed and braking, two (2) dust extraction hoods, air jet panel blow-off device &SIKO digital counters for adjustments. -- Panel Pre-Heater: Pre-heating the panel brings the panel to an appropriate temperature for better adhesion; this is especially beneficial in cooler temperatures. --Quartz lamp for heating substrate edge before glue application improved edge quality and optimum bonding. -- Multi-Purpose Magazine: A multi-purpose 2-coil magazine expands capability by running coiled material, strips, and solid wood bands. -- Magazine height adjustment allows for greater usage of varying panel heights by raising and lowering the magazine table, allowing the operator to center the panel on the edgebanding. -- Gluing System: (EVA - Hot Melt) QA 34 -Quick Melt Overhead Unit & heated roller applicator digitally displayed thermostat for both upper and lower unit. -- 34 mm Dia. Glue Roller allows for excellent control of temperature for optimum bonding results with individual adjustment for leading and trailing glue gates. -- Lower melting unit equipped with automatic glue level control. Melting capacity: 12 KG/Hr (26 Lbs/Hr) -- Pressure Section: Manual Adjustment with digital counter, (1) large 160 mm dia. driven & (6) 70 mm dia idle rollers, pneumatic pressure control depending on edgebanding material used. -- WORKSTATIONSEnd Trimming Unit HL 81: 0.8 kW(1.0 HP)x 2 - 200 Hz, 12,000 RPM Motors. to cut excess edge on the front & back of the panel; pneumatic adjusting from chamfer 30 deg. to straight cut. -- Rough/Pre-Trimming Unit: Top & bottom,0.55 kW (0.74 HP)x 2 - 12,000 RPM Motors; Height adjustment with the top pressure-beam and tilting range +/- 1°. -- Manually adjusted with digital counters. -- Profile/Bevel/Corner Rounding Unit FK 11: Multi function0.4 kW(0.54 HP) x 2)- 12,000 RPM Motor to fine trim the edge overhangs at the work-piece upper& lower edge, as well as trimming around the front & rear vertical edge; Servo controlled, Max. feed speed 20 MPM (65.6 FPM). -- Profile/Bevel Scraping Unit: Top & bottom for thick PVC/ABS, pneumatically activated. -- Flat Glue Scraper Unit: Top & bottom, pneumatically activated to remove potential glue squeeze-out. -- Buffing Unit: Top & bottom edge buffing/polishing. -- Spraying Units: Top/Bot

KOCH SBD-B BORING MACH. (FEED THRU DBL END TRIM, BORE & DOWEL): -- Specifications:0.6" - 1.18" (15 - 30 mm) Material thickness; 0.9" - 9.8" (23 - 250 mm) width; & 4.7" - 98.4" (120 - 2,500 mm) length cap.; -- Working pass height 36.2" (920 mm); Capacity of approx 25 Work Cycles/Min. -- Features:Motorized opening with digital setting. Automatic hopper feed with hydraulic stock feed beam and automatic return conveyor to operator. -- Each side equipped with: Trim saw units, Boring units with horizontal and vertical drilling, & Dowel insertion. -- Linear path control for stock transport with low profile machine bed and linear guides. Fixed stock stops. -- Adjustable working stations with Manual & motorized adjustments. -- Horizontal Drilling:Each side with (1) 2.7 HP (2 kW) - 3,400 RPM Boring unit. -- Each horizontal boring unit has a (6) Spindle Type D-1277 drilling chucks on 32 mm centers. -- Drilling Chucks hold 10 mm dia shank & 70 mm max bit length. -- Each head moving on linear guides with, drilling depth control, dust extractor hoods, blow-out jets to clean holes. -- Top Vertical Drilling:(4) Top Vertical Boring Units with rotating device. Each unit 2.7 HP (2 kW) - variable speed from 3,000 - 6,000 RPM. -- Each Drilling chuck with mechanical digital read out for manual finite adjustment with, KOCH's "QC" (quick change) system & rotating device. -- Drilling Chucks hold 10 mm dia drill bit shank & 70 mm max bit length. -- Each head moves on linear guides with, drilling depth control, dust extractor hoods, blow-out jets to clean holes. -- Each vertical unit can be equipped with "QC" Boring blocks (swivel 360°) with pneumatic locking. -- All Vertical units are equipped with pneumatic locking & individual adjustment of the boring block. -- Distance position readouts on all heads for finite "X"/"Y" adjustments; and "Z" axis boring depth control. -- Doweling:With (4) total dowel Inserters, (2) inserter on each side, with vibrating dowel bowl feeders. -- Includes automatic dowel measurement, pressurized glue tank, & back-wash rinsing tank. -- NOTE:This machine is currently setup for 0.437" dia. x 1.75" long dowels (11 mm dia. x 44.45 mm long dowels). Other sizes & additional dowel injectors can be purchased from Koch, at additional cost. -- Operator & Machine Control:Beckoff SPS PLC for machine function & error diagnosis. -- Operating Features:Electrical digital setting with all drill stations arranged with readouts for "X"/"Y"/"Z" axis positioning. -- The stationary machine side is on the LH side (seen in transport direction) and not adjustable. -- The RH is adjustable via motorized movement along the "X" axis. -- The machine is equipped with Hopper Feed & has a part stack capacity of approx 9.8" (250 mm) & working capacity of approx 48 Pieces/Min. -- Stock infeed belts move the workpiece through an intermediate hopper to the stock support. Then the workpiece is transported through the working stations by means of transfer

KOCH SBD-8 BORING MACH. (FEED THRU DBL END TRIM, BORE & DOWEL): -- Specifications:0.6" - 1.18" (15 - 30 mm) Material thickness; 0.9" - 9.8" (23 - 250 mm) width; & 10" - 98.4" (254 - 2,500 mm) length cap.; -- Working pass height 36.2" (920 mm); Capacity of approx 25 Work Cycles/Min. -- Features:Motorized opening with digital setting. Automatic hopper feed with hydraulic stock feed beam and automatic return conveyor to operator. -- Each side equipped with: Trim saw units, Boring units with horizontal and vertical drilling, & Dowel insertion. -- Linear path control for stock transport with low profile machine bed and linear guides. Fixed stock stops. -- Adjustable working stations with Manual & motorized adjustments. -- Horizontal Drilling:Each side with (1) 2.7 HP (2 kW) - 3,400 RPM Boring unit. -- Each horizontal boring unit has a (3) Spindle Type D-1277 drilling chucks on 32 mm centers. -- Drilling Chucks hold 10 mm dia shank & 70 mm max bit length. -- Each head moving on linear guides with, drilling depth control, dust extractor hoods, blow-out jets to clean holes. -- Top Vertical Drilling:(2) Top Vertical Boring Units with rotating device. Each unit 2.7 HP (2 kW) - variable speed from 3,000 - 6,000 RPM. -- Each Drilling chuck with mechanical digital read out for manual finite adjustment. -- Drilling Chucks hold 10 mm dia drill bit shank & 70 mm max bit length. -- Each head moves on guides with, drilling depth control, dust extractor hoods, blow-out jets to clean holes. -- Each vertical unit can be equipped with Boring blocks (swivel 0° - 90°) with pneumatic locking. -- All Vertical units are equipped with pneumatic locking & individual adjustment of the boring block. -- Distance position readouts on all heads for finite "X"/"Y" adjustments; and "Z" axis boring depth control. -- Doweling:With (2) total dowel Inserters, (2) inserter on each side, with vibrating dowel bowl feeders. -- Includes automatic dowel measurement, pressurized glue tank, & back-wash rinsing tank. -- NOTE:This machine is currently setup for 0.437" dia. x 1.75" long dowels (11 mm dia. x 44.45 mm long dowels). Other sizes & additional dowel injectors can be purchased from Koch, at additional cost. -- Operating Features:Mechanical digital readout setting for all drill stations for "X"/"Y"/"Z" axis positioning. -- The stationary machine side is on the LH side (seen in transport direction) and not adjustable. -- The RH is adjustable via motorized movement along the "X" axis. -- The machine is equipped with Hopper Feed & has a part stack capacity of approx 9.8" (250 mm) & working capacity of approx 48 Pieces/Min. -- Stock infeed belts move the workpiece through an intermediate hopper to the stock support. Then the workpiece is transported through the working stations by means of transfer belts with lateral stock alignment. -- Work pieces are automatically feed and positioned to pneumatic stops then clamped prior to trim, drilling or insertion. -- Compl

KOCH SPRINT-PTP-2-L CNC BORE, GLUE & DOWEL INSERTER: 0 -- Specifications: Automatic step-by-step, boring, glue injection & dowel insertion at random spacing. -- Working Capacity:Stock length (Y) from 4.25" - 31.4" (110 mm - 800 mm), Stock width (X) from 0.75" - 98.4" (20 mm - 2,500 mm),Stock thickness (Z) from 0.51" - 1.57" (13 mm - 40 mm), max. boring depth 1.1" (28 mm). 98.4" (2,500 mm) X-Axis divided into (2) work zones of 47.2" (1,200 mm) ea zone.One part can be processed, while the other is being unloaded or loaded. -- Positioning Speed: 344.5 FPM (105 MPM), boring & insertion capacity up to (60) dowels/Min -- Machining:(1) Horizontal boring spindle, 7,200 RPM, powered by 1.2 HP (0.9 kW) motor; (1) Glue injection & dowel inserting system, Dowel inserter is set up for 8 mm dia. x 30 - 35 mm long dowels (other dimensions available). -- Operator & Machine Control:12." Color touch screen monitor using Windows XP operating system with graphics & diagnostic. serial interface & USB connection.Menu driven operator interface for function control and graphic illustration of machine functions -- Complete with:Central lubrication system; (1) Vibrating hopper for dowel delivery; (8) Stock clamping cylinders; (1) Removable center stop for up to (2) working zones; "Air tight" pressurized 1:1 glue tank.(was only used with water) (2) Fixed fences (RH & LH side), double sided center fence. -- Actual Model is KOCH SPRINT-PTP-2-L

KOCH SPRINT PTP-2 CNC BORE, GLUE & DOWEL INSERTER: -- Specifications:Automatic step-by-step, boring, glue injection, and dowel insertion into panel components, drawer parts, chair pieces, etc. at random spacing.Programmed on a 12" color touchscreen monitor pad & stored in built-in CNC control using Windows XP Operating System with graphics & online diagnostic; serial interface & USB connection.Capacity: -- Panel width cap.: 20 mm (3/4") - 1,200 mm (47-1/4") Max. -- Panel Length:100 - 800 mm (4" - 31-1/2"). -- Material thicknes:14 mm - 60 mm (2.4") max. -- Max. boring depth: 50 mm (1-7/8"); standard for 8 mm dia. and 35 mm long dowels. -- 47" X-Axis divided into (2) work zones, 23-1/2" ea.; (1) part can be processed, while the other is being unloaded or loaded. Equipped with: -- (1) Horizontal boring spindle, 6,000 RPM, powered by 1 HP motor. -- (4) Stock clamping cylinders. -- High pressure patented "KOCH ELC" glue injection unit & dowel inserter head. -- Positioning speed of working units at 197 FPM; boring & insertion capacity up to (60) dowels/Min. Complete with: -- Overhead vibrating hopper for dowel feeding. -- "Airtight" pressurized 1:1 glue tank & "ELC" Electronic Glue Detection System (special patented "KOCH design" precision dosing valve w/digital adjustment). -- (2) Fixed fences (RH & LH side); 4-cycle start push buttons; (2) of them ready for center fence mounting to create (4) working fields for fast processing of narrow parts like stretchers, hangers or drawer parts, Center Fence is not included. -- CNC Control w/monitor & touchscreen pad, operator control cabinet, menu driven screen for function control, and graphic illustration of machine functions. NOTE: New glue valve, bucket, hoses & electronic safety sensor installed 2018. -- Actual Model is KOCH "SPRINT PTP-2".

KOCH - SPRINT-PLUS/I, ...CNC Bore, Glue & Dowel InserterSpecifications: -- For horizontal end drilling, gluing, & dowelling into stock ends (left-hand & right-hand sides); horizontal edge drilling; vertical face drilling from below. -- Table size: 20"; x 51"; x 35-1/2"; H; (2) 23-3/4"; W Working fields. -- X-Axis range (CNC): 1,200 (47") with (1) working field; 600 mm (23-1/2") with (2) working fields. -- Y-Axis adjustment range (manual): 0 - 50 mm (0" - 1.97"). -- Dowel diameter 8 mm (0.31").Equipped with: -- (4) 12"; L Pneumatic clamps. -- Horizontal drilling unit. -- Glue & dowel insertion unit. -- Vertical drilling unit from below, programmable along entire length of worktable (X-Axis). -- Manual table adjustment with: Adjustable support rail for movable & removable support elements for vertical drilling from below at any position required and for narrow parts & rails. -- 26"; Dia. x 7"; D vibratory bowl feeder. -- GRACO "HUSKY 307" 7 GPM 100 PSI air-operated diaphragm pump with Stall-free low pulsation air valve. -- PC Based CNC Control, with 12" display. -- Emergency stop device.Dimensions without Vibratory Bowl Feeder: 125" x 78" x 84" H.

KOCH BD-A BORING MACH. (FEED THRU CNC): -- Specifications: Model BD-A Boring Machine for straight rail-stock work pieces for Horizontal & Vertical Drilling; Infeed and outfeed pass height is 36.2" (920 mm) . The work pieces are transported through the working stations by means of a cam transport system.Stock is worked in clamped position. -- Stock dimensions: Stock length 9.8" - 59" (250 - 1500 mm), Stock width 1.50" - 9.8" (38 - 250 mm), Stock thickness 0.63" - 1.18" (16 - 30 mm) Note: The specified dimensions do not allow all possible combinations. -- Horizontal drilling station:Each side with (1) drilling unit with 2.7 HP (2 kW) - 3,400 RPM, Each horizontal boring heads with (3) Spindle Type D-1277 boring chucks on 16 mm centers;10 mm dia shank & 70 mm max bit lengthEach head moving on linear guides with, drilling depth control, dust extractor hoods, blow-out jets to clean holesLinear path control for stock transport with low profile machine bed and linear guides, fixed stock stops,Adjustable working stations with motorized width adjustment. -- Vertical Drilling head with rotating device:(2) LH & (2) RH Type D -1277, 2.7 HP (2 kW) Adjustable vertical boring heads with dust extraction hoods & variable speed from 3,000 - 6,000 RPM; Each Drilling chuck with (1) Drilling Spindle per chuck. Drilling Chucks with KOCH "QC" (quick change) system & rotating device each head; 10 mm dia drill bit shank & 70 mm max bit lengthEach head moving on linear guides with, drilling depth control, dust extractor hoods, blow-out jets to clean holesLinear path control for stock transport with low profile machine bed and linear guides, fixed stock stops,Mechanical digital read out for manual finite adjustment, (2) air hold down clamps, foot pedal control to start activation. -- Features:The stationary machine side is on the LH side (seen in transport direction) and not adjustable. The RH is adjustable via NC controlled "X" axis.The machine is equipped with Hopper Feed & has a part stack capacity of approx 9.8" (250 mm) & working capacity of approx 48 Pieces/Min.Stock infeed belts move the workpiece through an intermediate hopper to the stock support. Then the workpiece is transported through the working stations by means of transfer belts with lateral stock alignment; working pass height (36.2" (920 mm).Stock is worked in clamped position; There are stock outfeed belts at the machine outfeed. The workpiece is transferred to the out-feed hopper & removed manually. -- Operator & Machine Control:Beckoff SPS PLC for running the machine. -- Complete With: Open Station to add Dowel Inserting units at a later time ( Dowel units are not included) Manual Hand Pump Central Lubrication system for working units (1) NC controlled positioning of machine RH side (X), LH side is a fixed "0' point. Hopper Rail Feeding devices with capacity of approx 48 Work Pieces/Min. Separate drive for outfeed belt. Center Stock support. -- O

KOCH SPRINT SELECT.LINE 3000 CNC BORE, GLUE & DOWEL INSERTER + Horizontal Routing: -- Specifications:NC-positioning for "X", "Y" axis, "Z" axis is manual adjustment. Horizontal drilling station, with 3 individually controlled drilling spindles.Automatic step-by-step, boring, glue injection & dowel insertion into panel components, drawer parts, chair pieces, etc. at programmed random spacing. Horizontal Routing Unit for mortise, tenon, louver, strike plate, etc. type processing. -- Working Cap: Stock length (Y) from 4.25" - 31.5" (110 mm - 800 mm), stock width (X) from 0.75" - 120" (20 mm - 3,050 mm), stock thickness (Z) from 0.5" - 2.4" (4 mm - 60 mm), max. boring depth 1.1" (28 mm).120" (3,050 mm) "X" axis divided into (2) work zones of approx 59" 1,499 mm) ea., one part can be processed, while the other is being unloaded or loaded. -- Equipped with: (10) Stock clamping cylinders; Stock clamping system for panels/rails, small parts & solid wood parts.(3) Independent Horizontal boring spindle, 7,200 RPM, 1.25 HP (.9 kW) motor. (1) Horizontal Routing Unit for mortise, tenon, louver type processing, 9,000 RPM, 3HP (2.2 kW) motor. (1) Glue injection & dowel inserting system, with ELC – Electronic Glue Control delivered by a GRACH "Husky 307" glue pump.This Dowel Inserter is set up for 10 & 12 mm dia. dowels (other dimensions available). -- Operator Interface:NC Front end with 15" color touch screen monitor pad & stored in built-in CNC control using Windows type operating system with graphics and online diagnostic. serial interface and USB connection. Touch screen pad at eye-level height, integrated into machine frame structure, menu driven operator interface for function control and graphic illustration of machine functions. -- Features: Positioning speed of working units at 197 FPM (60 MPM), boring & insertion capacity up to (60) dowels/Min. -- Complete with:Central lubrication system; Overhead vibrating hopper for dowel feeding, "air tight" pressurized 1:1 glue tank.(2) Fixed fences (1-RH & 1-LH side), (1) pop up Center Fence & (2) working zones. -- Options Include:Some additional spare parts ordered with the machine & as pictured.

KOHLER - KG 100, ...Natural Gas GeneratorNatural gas-powered Generator. -- Rated at 125 KVA. -- Primary Voltage: 247/600 V - 3-phase, 60 Hz, 121 Amps. -- 100 kW, 150.5 Amps. -- 1,800 RPM - 12 Volt battery.