Quick Heavy Duty 14-Section Hydraulic Clamp Carrier, 16-1/2' Wide -- 14-Section Clamp Carrier 16-1/2' width cap.. -- (12) Heavy Duty zinc plated clamps per section for (168) total clamps. -- 38" opening on clamps; jaw sizes on clamps are 3-1/2" high x 4-3/4" wide with 1° inward draft. Equipped with: -- Dual Overhead Pneumatic Panel Flatteners for (2) operators -- Dual Hydraulic Clamp Tighteners for (2) operators -- Automatic Electric Motor Rotation with Indexing. -- Standard features include: Foot levelers, coiled air lines where used and flexible conduit for wires.

QUICK 6-Section Clamp Carrier with 16-1/2' width capacity6-Section Pneumatic Clamp Carrier with 16-1/2' width cap. -- (12) Heavy Duty zinc plated clamps per section (72 clamps total); 52" opening on clamps. -- Jaw size of clamps are 3-1/2" high x 4-3/4" wide, with 1° inward draft.Equipped with: -- Pneumatic overhead panel flattener 16-1/2' wide. -- Pneumatic clamp tightener -- Semi-automatic rotation via electric motor drive; -- Separate buttons for Front Rest Out, Rotate Reverse, Rotate Forward, and Front Rest In. -- Flexible conduit for electric wires.Features & Includes: -- Automatic air line oiler; -- High quality urethane finish coating. -- Toolbox with spare parts & tools.Floor space requirement: 236" W X 131"D X 148" H

QUICK 6-SECTION, 10'-1/2' Wide Pneumatic "Standard" Clamp Carrier: 6-Section Clamp typically produces (144) high quality edge glued panels per day (3 panels per section x 6 sections x 8 hours). Equipped with: -- (6) Sections with (8) clamps per section and 10-1/2' width capacity. -- (48) Clamps with 38" opening and 2-1/2" high x 4-3/4" wide jaws with 1° inward draft. Clamps use 3/4" dia. full-length screws; corrosion resistant, zinc plated, full box frame. Features: -- Semi-automatic electric motor drive. -- Pneumatic Panel Flattener for 10-1/2' wide Carrier with easy to use controls. -- Pneumatic Clamp Tightener with 3,000 RPM air wrench is (5 -10) times faster than competitive tighteners; 2-handed, trigger activated tightener is more confidence inspiring than the older, ergonomically awkward "swing-style" clamp tighteners. -- Fast tightening and full-length clamp screws eliminate need for manual adjustment of rear clamp jaws. Complete with: -- Foot levelers, coiled air lines, flexible conduit for electric wires, automatic air line oiler, high quality Urethane finish coating, and tool box with spare parts & tools. -- NOTE: Clamp Carrier can be expanded to (14) or (20) sections at a later time. 14-Section Clamp will produce (300) panels per shift; 20-Section machine, (500) panels per shift.

SAND-RITE DUO-DLX Spindle Sander; Horizontal spindle sander with 3/4 HP BALDOR motor. -- Optional brush heads sand irregular surfaces with out loss of shape, and the optional pneumatic drum heads (available in 2" to 8" diameters) allow the operator to regulate how firm the sanding head needs to be to conform the head to what they are sanding. -- Price does not include the stand - Add $308.00 Cast iron stand."Drums, brush heads, and sleeves are additional".Brush Head: ADD $ 175.00 2" X 8" pneumatic drum: ADD $ 140.008" X 9" pneumatic drum: ADD $ 302.00 Special note: 220 grit is the finest grit supplied for Brush Head

SANDINGMASTER - KSB-900, ...Single Head Wide Belt Sander36" Width cap.; combination sanding head.Head: Rubber covered spiral grooved contact roll & finishing platen.Specifications:15 HP Main motor.37" x 75" Abrasive belt size.Electronic tracking and air tensioning of abrasive belt.Rubber covered infeed & outfeed holddown rollers & holddown shoes.Variable feed speed 15 - 45 FPM via 1.5 HP motor.0" - 5" Manual part thickness opening.Includes: Optional floating bed for sanding fine veneers.Equipped with & Features:Extended infeed.Load meter.Disc brake on main motor.Safety stop bar.

SANDINGMASTER SA3300-900 TRIPLE HEAD WIDE BELT SANDER3-Head, 36" max. width cap. - 1st Head: 11" Dia. rubber covered contact roll, 24 HP motor; 2nd Head: 11" Dia. rubber covered contact roll, 18 HP motor; 3rd Head: Combination head with rubber covered contact roll and finishing platen, 18 HP motor. 37" x 75" Abrasive belts with electronic tracking. -- 2-Speed conveyor feed, 23 & 46 FPM, 1.0/1.7 HP motor, 0" - 6" motorized part thickness with LED readout, a joystick lever controls raise and lower of feed bed and start and stop of conveyor belt, also includes "SP-Matic" automatic part thickness setup. -- Thin veneer sanding package with rigid table setting for solid wood dimensioning and floating table setting for veneer sanding, infeed and outfeed spring loaded holddown shoes. -- Includes: Motor load meters, electronic brakes on sanding heads, infeed safety shutoff bar and 18" infeed conveyor area. Actual model "SA-3300-900".

SANDMAN DL7236 Downdraft Sanding Table;The SANDMAN Sanding Table is a dedicated sanding station that doubles as a workbench. -- 72" X 36" Rubberized work surface. -- 1.5 HP T.E.F.C. 220V 1-Phase motor with 10-5/8" LAU blower with sealed ball bearings. -- Industrial casters with 4" wheels, (2) ridged, (2) swivel-lock 2-ways. -- Hinged tilt-up top with gas strut lid support for easy filter servicing. -- Adjustable in height from 34" - 38". -- Grid system top adds versatility. -- 10.4 Cu. Ft. of built in storage area with 1 pull out shelf. -- 18 Months Limited WarrantyNOT IN STOCK - CALL OR EMAIL FOR CURRENT LEAD TIME TO SHIP. PRICING SUBJECT TO CONFIRMATION.

SANDMAN - DL7236: Downdraft Sanding TableSANDMAN Sanding Table is a dedicated sanding station that doubles as a workbench.Specifications: -- 72" x 36" Rubberized work surface. -- 1.5 HP T.E.F.C. - 220 V - 1-Phase motor with: 10-5/8" LAU Blower with sealed ball bearings. -- Industrial casters with: 4" Wheels: (2) Ridged; (2) swivel-lock 2-ways. -- Magnetic tool holder. -- Hinged tilt up top with: Gas strut lid support for easy filter servicing. -- Adjustable in height from: 34" - 38". -- Grid system top adds versatility. -- 10.4 Cu./ft. of built-in storage area with: 1 Pull out shelf. -- Easy filter service.

SANDMAN M74836 Downdraft Sanding TableGreat sanding table for a singular function such as doing cabinet doors, door fronts, etc. This downdraft table has a 6″ overhang on the front side making it good for sanding while sitting. Machine comes standard with casters, utility tray, & Felt-lined Platforms.Specifications: 48 L x 36" W top surface with heights of 32", 34" $ 36". -- Overhangs of 6" front. 0" back and 4" ends. -- (2) DP20252 Filters and (1) PF4029 pre-filter. -- 1 HP Baldor Motor – Standard Single Phase 110V (13 Amps) -- (18) Month warranty on parts.(Single and 3-Ph 220V available)NOT IN STOCK - CALL OR EMAIL FOR CURRENT LEAD TIME TO SHIP. PRICING SUBJECT TO CONFIRMATION.

SANDMAN M7236 Downdraft Sanding Table110V 1 HP (M7236) T.E.F.C Motor with 15’ power cord. -- 72" x 36" Rubberized work surface. -- 10-5/8" LAU blower with sealed ball bearings. -- Industrial casters with 5" wheels, (2) ridged and (2) swivel-lock 2-ways. -- Hinged tilt-up top with gas strut lid support for easy filter servicing. -- Grid system top adds versatility. -- (18) Month warranty on parts.NOT IN STOCK - CALL OR EMAIL FOR CURRENT LEAD TIME TO SHIP. PRICING SUBJECT TO CONFIRMATION.

SANDMAN DL9648 Downdraft Sanding TableThe DL9648 is a dedicated 96" x 48" sanding table that doubles as a workbench. The Sand Pro DL9648 is perfect for sanding large pieces such as doors or as a multi-person sanding station. Specifications: -- Table height 36", table size 96" x 48". -- (2) 1.5 HP TEFC motors with 7,400 CFM @ 1.5 SP and (2) 16" backward inclined fans. -- (6) Extended surface pleated filters each 20" x 25" x 2" deep w/ 1/2" netted polyester filter. Features: -- (4) 110 V duplex receptacles. -- Rubberized mar-proof top. -- Grid system top for jigs and fixtures. -- Hinged top with gas strut lid support for easy access to filters. -- (2) 10" x 32" Shelves. (2) 18" x 24" Storage drawers. -- Stainless steel hanger for air orbital sanders (choose 5" or 6"). Options: -- 3" Swivel casters (Adds 3/4" to machine height). -- Case of (12) replacement filters. -- Single phase available -- 18 Month Limited WarrantyNOT IN STOCK - CALL OR EMAIL FOR CURRENT LEAD TIME TO SHIP. PRICING SUBJECT TO CONFIRMATION.

SANI-TECH - SC1040/30, ...Auger Compactor -- Motor: 10 HP. -- Hopper capacity: 4.3 Cubic yards. -- Auger RPM: 10. -- Displacement rate: 270 Cubic Yards/Hour. -- 20-Yard Compactor

SAS SCORPION ENGINE PULLER Model SC40 DescriptionIncrease cash recovery from your recycling operationsSAS Forks Scorpion High Speed Motor Puller – Scrap Yard Engine Puller – Auto Recycling Engine Puller – Excellent for self service yards processing vehicles before crushing.Generate revenue:Process end of life vehicles in less than 60 seconds.Pull scrap engines and transmissions in 30 seconds.30% more revenue by separating metals from bodies.1000% more revenue per lb. on wire harness from engine compartment and dash.80% more visibility with a direct line of site from the operator’s window through the forks.Cycle time less than 15 seconds from park to full extension.Serviceable for long life. Replace blades in 3 hours or less.estimated only.Engineered & built for optimum performance:Engineered tough for continuous prying and durability.Hardened pins and bushings and grease-able pivot points for extended service life.Hydraulic hoses and cylinders are protected to minimize potential damage from sharp objects.Built with high strength blades and carriage skid plates for extended service.Clean up of ground debris is a snap with center plow blade.Speed is paramount in this design. Operator uses grapple from the cab, no torches, no personnel needed to hook up chains to pull or move engines. Safer, quicker and less costly removal of engines and transmissions.

Saturn Model 36x20 Slow-Speed Shredder --36" long x 20" wide chamber opening --1/2" knives. -- KYB MRH-30-SW2 hydraulic system powered by a 50-hp three-phase electric motor. --Comes equipped with stand and controls. -- Excellent for plastic, E-scrap, rubber, small tires, paper, cardboard, light metals.

SAVI HFK-250 Veneer Guillotine; General Specs: -- 102.4" (2,600 mm) Width cap., 4" daylight opening, hydraulically operated knife, 4 HP Leroy-Somer motor powers hydraulic unit with reservoir. -- Originally fitted with motorized parallel fence with 0.5 HP two speed gearmotor drive, push button operated, adjustable from 1" - 50" with magnified tape reader in front of machine. -- Equipped with: 2nd Cut feature with automatic reset, laser guide line light, photoelectric barrier guard for knife & hold-down beam, 2-hand operation of knife cycle. -- Note: Rear fence has been removed or modified. Shaft has chain/sprocket.

SAWSTOP - ICS 73230, ....Table Saw w/Safety "Stop Feature"Specifications: -- 10" Blade cap.; 7-1/2 HP motor; 3-1/8" depth of cut @ 0°; 2-1/4" depth of cut @ 45°; 13/16" max. dado width; 5/8" arbor dia. -- Features: -- Enclosed cabinet; Heavy-Duty belt drive; cast iron trunnions; SAWSTOPS's revolutionary flesh detecting safety mechanism. -- Includes: -- 52" "T-Glide" rip fence system; side support table and laminated top; 4" dust collection port; magnetic contractor motor control; main power switch with removable lock-out key. Actual model is: "ICS 73230"

5 HP motor with 8" or 10" blade cap. -- Features: SawStop Safety System, blade stops and retracts on accidental contact, protection is always on, performs continuous self checks, invisible protection, does not interfere with work, compatible with all standard blades; works on all woods and non-conductive materials. -- Includes bypass switch for cutting metal. European style riving knife to minimize kickback; Low profile blade guard for narrow cuts; Quick-change mount for guard and riving knife ÷Large start/stop paddle for hands-free shut off; Main power switch with removable lock-out key; Magnetic contactor motor control; Blade shroud for improved dust collection; Zero-clearance insert; Extra heavy castings ÷Widely spaced trunnions; Infinitely adjustable trunnion assembly for precision alignment. -- Also includes: Vertical slide blade elevation for increased stability; Long-lasting V-ribbed belts; cast iron handwheels; Two access doors in cabinet; Powder-coated cabinet.

SCHELLING FM-H 330/330 Automatic Panel Saw 129.9" (3,200 mm) Cutting length, 3.3" (85 mm) max. saw blade projection.Specifications & Features: -- 11 kW (15 HP) main & 1.6 kW (2 HP) scoring motor. -- Variable saw carriage travel speed from 0 - 262 FPM (80 MPM), constant return of 262 FPM (80 MPM). -- Electronically controlled overhead program fence with grippers, rack & pinion driven on both sides, forward speed from 0 - 262 FPM (80 MPM), return speed of 262 FPM (80 MPM); (6) Clamps open up to 3.9" (100 mm). -- 1,500 mm Long crosscut fence (front-to-back), (2) side/crosscut aligners for up to 87" crosscuts, (1) in front & (1) behind pressure beam. -- SCHELLING "COMPOSER" operating system; on-board SCHELLING optimizer, color monitor (displays cutting dimensions & patterns w/moving graphics), self-diagnostic, data input by keyboard & mouse or direct downloading from office PC is possible. Complete with: -- (3) Front mounted air float tables for moving panel from rip position to crosscut position; fully enclosed for safety with man-height sheet metal panels & wire screen windows.Specifications subject to verification.

SCHELLING FM-430/410 CNC Front Load Panel SawSpecifications & Features: 169" (4292 mm) Cutting length & 165.3" (4,200 mm) pull back, 3.75" (95 mm) max. saw blade projection; 25 HP (19 kW) 4,100 RPM main & 3.4 HP (2.5 kW) 5,600 RPM scoring motor. -- Equipped with: Variable saw carriage travel speed from 0 - 278.8 FPM (85 MPM), constant return of 278 FPM (85 MPM). -- Electronically controlled overhead program fence with rack & pinion driven on both sides; forward speed from 0 - 278 FPM (85 MPM), return speed of 278.8 FPM (85 MPM); equipped with (8) gripper clamps (open up to 5" (130 mm). -- Features: SCHELLING "COMPOSER" IBM-AT Compatible Computer Control; aftermarket color monitor (displays cutting dimensions and patterns w/moving graphics) , self-diagnostic, data input by keyboard; onboard optimization program. -- Complete with: 2-3/4" to 87" (2,200 mm) Long side/cross-cut aligning zone, (1) aligner in front & (1) behind the cut line. -- (3) Front mounted air float tables for moving panel from rip section to the cross-cut section, (2) movable and (1) fixed; each with their own blower. -- Rear of machine fully enclosed for safety with man-height sheet metal panels & wire screen windows. T

SCHELLING FXH 430/410 FRONT LOAD, AUTOMATIC PANEL SAW: -- Specifications:169" (4,300 mm) Cutting length & 167" (4,250 mm) pull back; 3.9" (99 mm) max. saw blade projection, 23 HP (17 kW) main & 3.5 HP ((2.6 kW) scoring motor. -- Saw Carriage: Electronically controlled saw carriage with rack & pinion drive; variable travel speed 1 - 394 FPM (1 - 120 MPM), constant return of 394 FPM (120 MPM). -- Pusher Fence: Electronically controlled overhead pusher fence, rack & pinion driven on both sides; (9) Gripper clamps that open up to 3.5" (90 mm). -- Forward speed 0 - 262 FPM (0 - 80 MPM), return speed 262 (80 MPM) FPM; travel via brushless AC Servo Drive -- Operator & Machine Control:PC Front-end with Schelling "MCS" + Windows "NT" operating system.17" Color display with SVGA resolution (displays cutting dimensions & patterns w/moving graphics); virtually unlimited storage capacity, standard keyboard & mouse.Ethernet card; 128 MB Ram, 56K modem. Integrated graphical self-diagnostic, remote diagnostics by the factory is possible via dedicated phone line; data input by keyboard or possible direct downloading from office PC.SCHELLING "MCS" software displays simulation of patterns before actual cutting; graphical representations of cut-to-size parts in production shows the operator what to do in "real time". -- Complete with:2,300 mm Long crosscut fence (front-to-back), (2) automatic side/crosscut aligners for up to 87" (2,210 mm) crosscuts, (1) in front & (1) behind pressure beam cut line.(3) Front mounted air floatation tables, each table 24" x 83" (609 x 2,108 mm), rear of machine fully enclosed for safety with man-height safety fencing. -- Actual Model is SCHELLING FXH 430/410