RAPTOR - MINI TG, ...Tire Grinder / ShredderRAPTOR Tire Grinders are the most durable and easy to use Shredders built. Specfications: -- Feed opening: 33" x 36". -- Main motor: 200 HP. -- Size material down to: 3/4". -- Screen size: 3/4". -- Separates steel from rubber: 75% to 80%. -- Capacity: 2 Tons per hour (approx.).Equipped with: -- Full hardened knives. -- Electric control panel. -- Stand and infeed hopper.NOTE: New beearings and seals, a rebuilt gearbox, rebuilt gear reducer, and rebuilt electric motors. New frame and screen, too!

RED SEAL HVAC 960,000 BTU Natural Gas Boiler System in Containerized Boiler Room: -- Specifications:Built by Red Seal HVAC Specialists in 2021 and approved by all relevant Canadian codes and inspections.The container has inputs for natural gas, exhaust chimney, passive makeup air louver, rigid insulation on walls, and an output for an insulated glycol line into your building or intended use.Approximately half of the container is empty space and can be used for storing appropriate items like maintenance tools. -- Natural Gas Boiler:The boiler is a 2004, made in Canada by Allied Boiler, Model # AAE960-N-E-M, Natural Gas, 960,000 BTU Input. Max. Water Pressure/Temp 160psi / 250°F.This boiler system was used to heat a drying oven, a air makeup unit, and had extra capacity for heating truck dock approaches in the winter.

REM - CC10, ...Used Can FlattenerThe REM Can Crusher is a complete separating, crushing, and blowing unit for aluminum cans.Specifications: -- Efficiently processes: 1,800 - 2,000 Lbs per hour. -- Load cans in the hopper and the conveyor carries the cans across the magnetic head pulley separating the steel from aluminum. -- The aluminum cans are crushed between a steel pressure plate and the rotating crusher drum with hardened steel bars; the cans then drop into a high-velocity air stream and are blown into a trailer or storage container. -- Features: 16" Wide belt; Crusher with: 10 HP 240/480-Volt, 3-phase; Blower with: 7.5 HP 240/480-Volt, 3-phase.

REM - PERF-5 MECH, ...Plastic Bottle Perforator -- One Lot: (2) Units -- 24" Wide Heavy Duty perforating drum with: Spring-Loaded pressure plate -- Capacity: 900 Lbs (PET Bottles) per Hour per Unit -- Motor: 5 HP at 1,800 RPM -- (1) Perforator used for 1-Week only; other Unit still in the w!rapper -- No Conveyor -- Loaded onto your Truck

RENZO BORGONO 800/I Hot Embosser. Machine is designed to "hot engrave" decorations onto picture frames, furniture accessories and mouldings. Heats the pattern wheel and presses it into wood transferring the design onto the product. -- Max. 450 mm(7.7") Engraving width cap.; 700 mm (27.5") material width cap., MIn: 100 mmm (3.94") width; 80 mm (3-1") dia. arbor; 140 mm (5.5") min. and 440 mm (17.3") max. embossing roller dia.; 3 mm (1/8") max. embossing depth with base-relief rollers and 7 mm (0.27)") max. depth with cutting edge rollers. -- 1.5 HP (1.1KW) Top drive gearmotor, feed speed 5.5 - 26 FPM output. -- Approx 8 KW heating by electric lamps, with thermal probe/thermostat. -- Water cooled shaft to avoid flexing and hear propagation. Coolant circulation pump 0.12 HP. -- Overall Dimensions: 1200 mm x 1400 mm x 17 mm height (48" x 55.5 x 71" H), Net weight: 950 Kg/2100 Lbs..

RENZO BORGONOVO, BL 94-2, ...Vertical Moulding Stacker.This 2-ARM AUTO STACKER has been specially designed to facilitate the loading of mouldings, picture frame strips, and other processed lineal parts onto drying racks. It eliminates the manual handling of workpieces which can mar the finish. It also increases productivity and efficiency compared to manual stacking. The machine can work with moulding of the same length or of varying lengths at the same time. -- Workpiece Length: 3,000 mm (118") Max. & 1,800 mm (72") min. workpiece width; 20 mm min. and 150 mm (6") max. material width cap. -- Stacking Capacity: (20 - 30) Pieces per minute. -- Overall Height: 2,200 mm (87"). - Overall width: 2,300 mm (91"). - Overall Length: 3,400 (134"). - Work Height: At Infeed 860 mm(34"). - Racks has (11) arms that extend out approx. 39" with 4" in between arms. -- Automatically loads "just painted" mouldings onto air drying rack. -- Process: As moulding exits coater, it is moved by belt conveyor to (2) arms which lift the piece up-and-over the top of the Stacker Station; coming down the other side, it places the moulding onto (2) arms, and a belt conveyor transfers the piece onto the 11-tier Drying Cart. -- Lifting can be triggered by electric photoeye to determine position of off-feed arms (arms move down as each tier of the rack is filled) and place moulding on the rack (indexing back-to-front). -- One rack included; additional racks, each ...$ 900.Machine overall dimensions: 3,400 x 2,300 x 2,200' weight: 1,200 kG.

RENZO BORGONOVO - BL 94-3, ... Vertical Moulding Stacker. This 3-ARM AUTO STACKER has been specially designed to facilitate the loading of mouldings, picture frame strips, and other processed linear parts onto drying racks.It eliminates manual handling of workpieces, which can mar the finish. It also increases productivity and efficiency compared to manual stacking. The machine can work with moulding of the same length or of varying lengths at the same time.Specifications: -- Workpiece Lengths are 4,900 mm (192") Max. & 1,500 mm (58") min. workpiece length, 20 mm min. and 150 mm (6") max. material width cap. -- Stacking Capacity - (20 - 30) pieces/Min. -- Overall Height of 2,200 mm (87"); Overall Width 2,300 mm (91"); Overall Length of 4,000 (157"). -- Work Height at Infeed 860 mm ( 34"); Racks have (11) arms that extend out approx. 39" with 4" in between arms.Operation: -- Automatically loads just-painted mouldings onto air drying rack. -- Process: As moulding exits Coater, it is moved by belt conveyor to (3) arms, which lift the piece up and over the top of the Stacker Station; coming down the other side, it places the moulding onto (3) arms. A belt conveyor transfers the piece onto the 11-tier drying cart. -- Lifting can be triggered by electric photo-eye to determine the position of off-feed arms (arms move down as each tier of the rack is filled) and place moulding on the rack (indexing back-to-front).This Stacker comes with (1) rack; additional racks are available, priced at ...$ 1,950 each

RENZO BORGONOVO - SP 6P, ...6-Gun Spray Machine with 3/4" - 12" width cap.3-1/4" Max, part thickness and 32" min. part length. Standard specifications: -- (6) Gun mounts made from aluminum rods and HDPE mounting brackets, for connections for (6) HVLP automatic spray guns, and (1) dual diaphragm fluid pump. (Guns and Pumps are not included). -- Complete with: Teflon coated recovery cabinet for each spray station and easy rollout feature, front access door with large viewing window & gas shock support arms. -- (2) Paint circuits with (3) spray guns each (guns not included).Features: -- Machine is operated with a central control panel and gun timing is controlled by a PLC that times the spray guns in relation to the length of the work piece and feed speed. -- PLC Records the number of workpieces and total linear feet processed in session. -- The machine is set up with infeed & outfeed conveyors that operate at any speed between 60 and 300 FPM and is made up of Antistatic and Antisolvent belts and intermediate steel rollers between Spray Stations. -- 11.8" Dia., 1.5 HP exhaust fan rated at 4,000 cbm/Hr. -- This Sprayer integrates easily into any line whether as a primary unit or as an intermediate step. -- Overall length is just under 10'.Sprayer will include:qty (1) WAGNER HVLP Zip52 pump $1920.00qty (6) WAGNER HVLP aSP 30 spray guns with 1.2 nozzle $5,616.00Working dimensions: -- Length: Min. 800 mm / max. infinite. -- Width: Min. 15 / 300 mm. -- Height: Min. 15 mm / max. 100 mm. -- Height of worktable: 900 mm. -- Compressed air consumption - NI/min 1,500 – 2,000. Overall size: 3,000 x 2,900 x 2,220 mm and 800 kG (I,750 Lbs).

RENZO BORGONOVO MVS-2500 Automatic Sanding and Buffing MachineFOR LINEAR FRAMES AND PROFILES - Sanding and buffing of frames, rods, ledges and fitting parts of veneer, solid, raw or varnished wood, etc. (processing of 3 sides for each pass). -- Advancing speed electronically variable by inverter: 10 TO 50 M/MIN. -- Total power: kW 10,5 (14 HP) -- Compressed air: Atm 6 -- Total exhaust capacity; m3/h. 2800 (25 m/sec.) -- Working height: mm. 10 min. mm. 100 max. -- Working width: mm. 20 min. mm. 200 max. -- Working length: mm. 1200 min.DISC SANDING UNITS TYPE “SCOTCH BRITE"; (N° 4) -- Power motor: 3 HP (2.2 kW) -- Rotation speed: 1400 RPM -- Disc sanding unit holder shaft diameter: mm. 30 -- Spindle-disc sanding unit connection flange diameter: mm. 76 -- Disc sanding unit diameter: mm. 200 max. -- Disc sanding unit height: mm. 100 max. -- Dust suction hood diameter: mm. 100 -- Extraction rate: m3/h. 700 (25 m/sec.)

RENZO BORGONOVO - SP 6P, ...6-Gun Spray Machine with 3/4" - 12" width cap.3-1/4" Max, part thickness and 32" min. part length. Standard specifications: -- (6) Gun mounts made from aluminum rods and HDPE mounting brackets, for connections for (6) HVLP automatic spray guns, and (1) dual diaphragm fluid pump. (Guns and Pumps are not included). -- Complete with: Teflon coated recovery cabinet for each spray station and easy rollout feature, front access door with large viewing window & gas shock support arms. -- (2) Paint circuits with (3) spray guns each (guns not included).Features: -- Machine is operated with a central control panel and gun timing is controlled by a PLC that times the spray guns in relation to the length of the work piece and feed speed. -- PLC Records the number of workpieces and total linear feet processed in session. -- The machine is set up with infeed & outfeed conveyors that operate at any speed between 60 and 300 FPM and is made up of Antistatic and Antisolvent belts and intermediate steel rollers between Spray Stations. -- 11.8" Dia., 1.5 HP exhaust fan rated at 4,000 cbm/Hr. -- This Sprayer integrates easily into any line whether as a primary unit or as an intermediate step. -- Overall length is just under 10'.The Machine is priced with no guns or supply installed, these will need to be added by the buyer or a separate quote can be requested for guns and supply pumps.Working dimensions: -- Length: Min. 800 mm / max. infinite. -- Width: Min. 15 / 300 mm. -- Height: Min. 15 mm / max. 100 mm. -- Height of worktable: 900 mm. -- Compressed air consumption - NI/min 1,500 – 2,000. Optional: &#9679 InHand Networks Industrial Router &#9679 Overall machine dimensions and weight &#9679 Teleservice module for remote troubleshootingPrice includes the following options: &#9679 Stainless Steel carriage &#9679 Teleservice module for remote service.PRICE IS FOB EAST COAST PORT, INLAND FREIGHT WILL BE QUOTED.Overall size: 3,000 x 2,900 x 2,220 mm and 800 kG (I,750 Lbs).

RILESA UNI-X 2200 FEED THUR CNC BORING MACHINE W/4-SIDE DRILLING, in one pass. -- Specifications:Working Capacity; 230 mm - 2,200 mm (9' - 86.6") Length, 20 mm - 250 mm ((0.78" - 9.84" width, 10 mm - 60 mm (0.39" - 2.36") thickness.Capacity: up to 900 parts/hour without cross drilling. -- Features:One-man operated. 4-side drilling, in one pass. With Rilesa UNI-X drilling machine you get precision, quality and extreme high capacity. It is well suited to both small and large dimensions. It has short set up time and minimal maintenance. -- Polyurethane an guides ensure gentle handling of components. The restraining clamp automatically adjust to component width ensuring correct location to the zero point. -- The drilling boxes are designed for high speed drilling, 4500 RPM. The tool inserts can be chosen Between direct or snap assembly. Special drill boxes can be manufactured to specific customer requirements. -- Assembly of drill boxes takes place with a snap function and is simply locked with screw. The drill box can be freely turned between 0 and 90°. In the outer positions there are stops. -- The drill groups unique design gives a high degree of adjustment flexibility. The center distance between groups is 95 mm. Pneumatic over hydraulic drill feed. Drill speed, 4000 RPM. -- The components are fed in pneumatically up to the reference stop and locked securely in this position. A unique safe regulated system makes sure the component is in place without pressmark. -- The operator uses signal lamps to make adjustments. The operator manually moves the drill groups into position checking the lights. Yellow to green = Tolerance. -- The machine closed design with built in dust extraction gives the perfect place to work. Notice the sturdy construction of the machine body. -- Loading of components is very easy by pushing the stack in through the brushes. The machine components are transported gently back to the operator. The conveyer can run continuously or in step mode. -- For long components support elements can easily be added. They are located with a simple clamp and ensure straightening of the workpiece. -- The machine can be delivered with sideways displacement of the drilling group. The drilling group displace up to 100 mm, this function combined with programming of the drilling, do difficult drilling in one passage, possible. -- The control system is integrated in the back of the machine, well protected against dust. There is room for future expansions to be added. -- Hopper / Magazine:Pneumatic magazine with ergonomics and user friendly access. Automatic fixation to the zero point by a pneumatic counter clamp with polyurethane and nylon covering for careful handling of the component. -- Return conveyor with an adjustable catcher tray, build-in clamp cylinder mounted at each end, for flexible and safe clamping of the components, adjustable catcher tray. -- Operator Interface:Advanced 15"; color TFT touch screen control system where

RITTER R-1475 Raised Panel Door Router SetupSpecifications: -- 36" X 72" Work table area, 24" door width & unlimited door length capacity. Capable of producing a complete raised panel detail in one (1) minute. Routers are guided by the fences or templates attached to the fences.Equipped with: -- (4) 3" Bore AC 20 clamp cylinders; (4) 1-1/2" x 1-1/2" adjustable fences; -- (2) 1.5 HP router motors with dust hoods; (1) 7/8 HP router with dust hood; and (1) 1475-H Heavy Duty 3-1/2 HP Hogging Router w/ cutter & dust hood.Complete with: -- 1475-A Tooling set, template guides; regulator and gauge; and (4) 2-1/2" dia. X 8' long flexible dust collection hoses.

Designed for machining of beaded face frames, cabinet doors and related joint construction. The machine miters all required corners and notches without the need to change a set-up. -- Production time is reduced to seconds with the use of the 6,500 RPM cutterhead capable of machining (2) parts at the same time. -- Standard Features: 7.5 HP spindle drive motor, 40 MM diameter 6500 RPM spindle, 7" maximum cutter head diameter, Adjustable pneumatic cutter head feed stroke, 60" stile & rail alignment fence, 16" material width capacity, (8) quick reference material fence alignment stops (6) quick reference fence offset stops, (4) hold down clamp cylinders. -- 48" wide table with 34" fixed work table height, magnetic controls, foot pedal controlled machining cycle. -- Tooling Options Sold Separately ($4,500): 7/8" Cutter head pattern, 5/16" bead carbide tipped, 1" cutter head pattern, 5/16" bead carbide tipped. Custom pattern heads upon request. -- Additional Options: 72" & 84" alignment fences, additional fence offset stops, additional fence stops. -- 4" diameter dust outlet. Weight: 1,430 lbs. -- This machine is also available with a 5 HP 220V single phase motor at the same price.

RITTER DR-3553 Profile Sander2 HP TEFC Motor with direct drive spindle which tilts 90° forward & 20° backward.Specifications: -- 400 - 1,800 RPM Inverter controlled variable speed with RPM display. -- 4" Vertical & 8" horizontal spindle adjustment. -- 36" x 33" Solid northern hard maple tabletop and 36" table height. -- 1-1/4" Dia. x 4" long spindle to accept standard sanding discs and profile discs made to customer's specifications. -- Enclosed fabricated steel base. -- Dust hood w/piano hinge for easy ascess to sanding disc. -- Stationary fence and large hand wheels for easy spindle adjustment.

High quality American made fixed spindle Shaper. -- Fabricated steel base with precision ground built-in cast iron table. -- Table insert rings to easily accommodate a wide range of cutterhead dia. -- Interchangeable spindle with lock for easy tool change. -- (8) Spindle speed settings for a variety of size cutters. -- Spindle reversing switch as standard. -- Standard 3/4" x 3/8" groove in table for miter gauge (not included). -- Large hand wheel for manual spindle height adjustment. -- Electronic digital height display. -- Micro-adjustable fence that easily adjusts for short runs. -- Large cabinet style door for easy access to motor & quill assembly. -- Self-braking motor. -- Magnetic starter & thermal overload switch. -- Integrated dust shroud & spindle guard assembly with manual holddown. -- Emergency stop. -- Operations manual, parts list & tool kit.

RITTER R-20 Double Spindle Shaper:High quality American made fixed spindle Shaper with (2) Spindles. -- Fabricated steel base with precision ground built-in cast iron table. -- Table insert rings to easily accommodate a wide range of cutterhead dia. (4-1/2" max. opening without rings). -- (2) Solid 1-1/4" spindle with lock for easy tool change. -- (2) Spindle speed settings for a variety of size cutter sizes and Spindle reversing switch. -- Standard 3/4" x 3/8" groove in table for miter gauge (not included). -- Large hand wheel for manual spindle height adjustment. -- Micro-adjustable fence that easily adjusts for short runs. -- Large cabinet style door for easy access to motor & quill assembly. -- Self-braking motor and Emergency stop. -- Magnetic starter & thermal overload switch. -- Integrated dust shroud & spindle guard assembly with manual holddown. -- Operations manual, parts list & tool kit.

RITTER R-30RP Raised Panel Door Shaper(3) Shaper Spindles mounted in a precision ground worktable (68" X 52" Deep X 36" Working Height ) Designed for running raised panels, as well as style & rail material for raised panel doors. -- Preset Spindle Locations, Equipped with (2) 5 H.P. Spindle Drive Motors On Right And Left Spindles, and (1) 7.5 H.P. Spindle Drive Motor At Center Spindle. -- The 1-1/4" Diameter Variable Speed Spindles are driven with Micro-V Belts. 5-1/2" max. cutter dia. -- 1st Spindle: 2" high x 12" wide max. tenon. 2nd Spindle: Setup for shaping of raised panels. 3rd Spindle: Setup for machining of style & rail and outside lip of door. -- Complete with: Micro Adjusting Fences, Miter Gage Slot at Right Hand Spindle (3/4" W X 3/8" Deep), Dust hoods (3 - 4" Connections), and Door Interlock Safety Switches.Suggested Options -- H154: PANELCRAFTER 24" Capacity Panel Jig, with 2 Cylinders. -- Jigs float on a cushion of air for smooth, easy operation. Proven design for years of trouble free use. Single thumb lever activates floating and clamping cylinders. Use with material thickness up to 2" thick. Self centering mechanism, and Variable flotation regulation. Large hand grips help operator control work piece. Change door style by simply changing the templates using a wide range of template designs and sizes. This Option requires 2 CFM at 80-100 PSI of supplied air.- R10TESA: Coping Attachment -- Fits any 3/4" by 3/8" deep slot, 2" X 12" capacity, with (3) Adjustable hold down clamps.- H161: Power Material Feeder, with reversing. -- (3) 20mm Rubber Rollers, 1HP Motor, 8 Adjustable Speeds (6,13,18,21,36,42,54,102 FPM)

RITTER R-26 Boring Machine (2-Head Line Boring)(2) 13-Spindle belt driven drill heads, drills from the top down, each head with 2 HP - 3,450 RPM motor; both heads with rack & pinion adjustment 4" min. to 24" max. spacing. -- Spindles on 2" centers, 10 mm collets; 30" x 48" table, table cycles up/down with a 3" stroke. -- Equipped with: (2) Adjustable stops, (2) spring hold-downs on the rear head; and foot pedal actuated boring cycle.

SCM M3 Multi-Blade Dip Chain Gang Rip SawSpecifications: -- 300 mm (11.81") Width cap. -- 110 mm (4.33") Max. depth of cut. -- 8-3/4" Throat depth. -- 390 mm (15.35") Min. stock length. -- 200 - 350 mm (7.87" - 13.78") Blade diameter. -- Arbor dia. 70 mm (2.76"). -- Table size 750 x 1,530 x 750 mm H (29-1/2" x 60.24" x 29-1/2" H). -- Blade speed 4,200 RPM. -- Feed speeds 6 - 48 MPM (19 - 157 FPM).Equipped with: -- 44 kW (60 HP) - 3,554 RPM Blade motor. -- Variable speed drive feed chain motor. (2) Upper infeed & (2) Upper outfeed 4" Dia. rollers, Automatic chain lubrication. -- Top & bottom anti-kickback fingers. -- Main dust hood, with 200 mm (7.87") Dia. outlet. -- 40"; x 2-3/4"; H Adjustable infeed fence. -- Motor load meter.Complete with: -- Operation & Maintenance Manual. -- Tooling (As pictured).

SCM ROUTECH RECORD 130 FLAT TABLE MACHINE (W/ATC/BORING): -- Specifications:4' x 10' Single Table machine: stationary extruded aluminum table is machined with a square grid pattern for fixturing parts,Grid pattern allows use of vacuum pods or closed cell rope gasketing material and use of spoil boards for "nested based machining". -- Working field:"X" axis 120" (3,048 mm), “Y"; axis 49.2"; (1,250 mm, "Z" axis stroke is 12" (305 mm). -- Positioning speed:"X" axis 260 FPM (80 MPM), "Y" axis 180 FPM (55 MPM), "Z" axis 82 FPM (25 MPM).Closed loop AC Servo drive system driving precision ground ball screws, all axes ride on extra large precision profile linear guideways. -- Boring Unit:(12) vertical spindles, (7) in "X" axis & (5) in "Y" axis;(6) Horizontal spindles with (2+2) in "X" axis & (1+1) in "Y" axis. -- Machining:(1) 10 HP (7.5 kW) "Power 2000" Electro spindle w/lifetime lubrication & HSK F63 adaptor, spindle speeds from 6,000 - 18,000 RPM;(1) 12-position ATC tool plate mounted on the head for "on the fly" ATC. -- Operator & Machine Control:PC Front end with XILOG Plus + WINDOWS operating system; "NUM 1000" PLC featuring (3) axes simultaneous control,15" high resolution CRT; 1.2 GB Hard drive, ergonomic industrial keyboard & mouse; 1.44MB floppy disk drive; serial ports for RS-232; all housed in a separate dust free cabinet -- Complete with:(1) 12 HP "BECKER" vacuum pump; safety BUMP stop. -- Actual Model is SCMI ROUTECH RECORD 130-121.