ROSE MACHINERY BDH/LC/LCFT Automated Infeed SystemAutomated, high speed Infeed System for Gang Rip Saws of all makes and models and other similar machines. -- 5-Arm Breakdown Hoist - Electric hoist accepts loads 4' wide x 4' high x 4' - 24' long; 10 HP gear motor (with brake) powers the hoist and holds the load. -- Hoist actuated through foot switches for up & down; limit switches provide max. up & down positions; (5) lifting arms tilt load at 50° allowing layers to spill onto the takeaway conveyor; 16,000 Lbs. max. lift cap. -- Landing Chain - Features: (6) Strands of roller chain; powered by a 5 HP gear motor at 60 FPM nominal rate. -- Tail end constructed with integral slide, stock transits from Breakdown Hoist; head shaft & gear motor supported by tubular steel frame with bolts to allow for leveling at installation. -- Material stops at the head end so the operator can flip & grade each piece. -- Chain races fabricated from steel, UHMW PE wear strips on the top race and on the return race; conveyor is 42' long. -- Magnetic motor starter with foot switch for operator to start & stop of the chain. -- Lateral Chain Feed Table "LCF2013-20": Feeds material 3" - 10" wide x 4' to 24' long x 1" to 3" thick; variable 50 - 200 FPM Feed rate; adjustable fence throughout 3/4" range for alignment with the Rip Saw (or other machines). -- (6) 30" long, low friction steel flattop infeed chains for long life non-marking transport; 1 HP gear motor. -- (3) Powered smooth steel & non-marking feed rolls, 2 HP gear motor; rolls & chains controlled by variable speed drives. -- (3) Overhead pinch rollers, 5" dia., urethane covered; 1st (2) pinch rollers powered by individual 2-1/2" bore air cylinders to singulate pieces onto a 2' bridge; 3rd roller keeps the board moving on the bridge; pinch rolls triggered by photoelectric cells. -- Note: Fabricated frames and appropriate parts of the items in this quotation will be painted with (1) coat of industrial grade Shady Lane Green enamel; guards and appropriate moving parts painted with Safety Orange. -- All gear motors, mechanical equipment, limit switches, sensors or photoelectric devices, as required for each item of this quotation, are supplied and mounted; all pneumatic cylinders or other pneumatic power devices and their valves supplied and mounted; connecting hoses & fittings installed. -- Filter/Regulator units supplied, mounted, and connected by hose to the valves; Note: Compressed air service to equipment is by others.

Ripsaw Feeder with 32" wide feed rolls on 18" thru 28" roll centers; will feed 3' thru 16' lumber. With 24" of in-out fence travel; feed speeds from 50 to 150 FPM; 3/4 HP feed roll drive and 3/4 HP fence drive via gear motor with brake. -- Fabricated frame of structural steel with boots that allow +/- 1" elevation adjustment. 3-1/2" dia. steel feed rolls driven by a variable frequency drive for speed adjustment; rolls are canted to aid in holding stock against the fence. -- Powered fence with 24" fence travel is easily shifted via joystick control for stock alignment with the sawblades. -- With pneumatic powered gate to keep material from feeding until the operator initiates the feed sequence. -- Urethane covered idler pinch roll is attached to the fence and is powered down at the start of the feed sequence. When a photocell detects the board is clear of the gate, the pinch roll and gate will return to their normal position. Electrical control panel ready for connection to the power supply.

ROSE MACHINERY HBR Horizontal Band RE-RIP SawThe Horizontal Band Re-Rip Saw is an effective and efficient means of ripping short blocks into as many as six (6) set rip widths. Rip widths are easily adjustable, as well as the setting for stock thickness.Advantages of the system: -- Compact, efficient use of floor space. -- Accurate cutting of rips with minimum tear-out. -- Short blocks, 4" minimum length, without taper problems. -- Straight through feed design, good for sorting. -- Minimum dust collection required. -- Single point scrap collection. -- One saw drive motor, requires less power. -- Safety, no kickback problems.Specifications: -- Five (5) rip widths - (6) optional -- 20 HP bandsaw drive -- 30" diameter band wheels, 2" wide face -- (2) 3/4 HP feed works drives -- 1-1/2 HP feed belt drive -- 1" to 6" rip width (independently adjustable in each lane) -- 10" maximum board width at maximum rip -- 4" maximum waste piece width -- 3/4" to 2" stock thickness (all lanes adjust together) -- 4" minimum stock length -- 36" maximum stock length -- 80 FPM feed speed -- 52" to 58" pass line height -- Motor starters and push buttons included, wired for 440 volt, 3 phase, 60 Hz (uses standard mag starters) -- An automatic band lubrication system is includedOptional Equipment: -- For SIX (6) LANES, add ...$5,600 (SORTER increases $3,700) -- Automatic machine grease lubrication system, add ...$ 9,200 -- Ergonomic overhead stock slide, add ...$ 5,600 -- Output conveyor and sorter for 5-LANEsingle side discharge, add ...$47,300 -- Output conveyor and sorter for 6-LANE single side discharge, add ...$51,100 -- Operator's platform, add ...$ 7,900 -- Optional voltage configuration: 220/380/440V, 50HZ, add ...$2,900 -- Start-up and training, add $1,000 per day plus expenses at costHorsepower Requirements: -- (1) @ 20 HP -- (1) @ 1-1/2 HP -- (2) @ 3/4 HPDust Collection: -- (2) outlets, 6" diameter, 5,200 FPM velocity @ 2,300 CFMCompressed Air Required: -- 90 PSI @ 1.4 CFM

ROSE MACHINERY LCFCMS14 PANEL RIPPER TO MOULDER TRANSFER SYSTEM OUTFEED ROLLCASE: -- Outfeed Rollcase receives material from the LHI Panel Ripper at 47 1/4"; elevation and drops down to place the lumber onto the Transfer Chains at 42"; elevation. 66"; wide rolls are 2-12"; diameter steel rolls, snap in style on 12"; centers. Rolls are powered by a line shaft using round Eagle Belts and a 1-1/2 HP gear-motor. The conveyor will be fabricated from tubular and sheet steel and designed to interface with the Transfer Chains. The conveyor speed is 80-120 FPM to create a gap between courses exiting the Panel Ripper. The drop will be triggered when a photocell detects the leading end of the boards, creating a far side lumber line. A pneumatic cylinder provides lifting power. When the transferred boards clear the rolls, another photocell triggers the rolls to return to the up position. Stock length handled by the Outfeed Rollcase is from 6’ to 16’. Elevation adjustment is +/- 1";.TRANSFER CHAINS: -- Transfer Chains receive material from the Outfeed Rollcase. The Transfer Chains are fabricated from tubular and structural steel. There are (6) strands of 2060H conveyor chain approximately 17’-6"; CC long, leaving 11’ clear space to accumulate (2) layers of ripped strips. (2) sets of pin stops are incorporated to keep the layers separate. The conveyor is powered by a 1-1/2 HP gear motor. Conveyor speed is 90 FPM maximum. Elevation is 42"; +/- 1";. LATERAL CHAIN FEED TABLE (ROSE MODEL LCFCMS14): -- Standard duty low friction flat top steel infeed chains drive the stock to the fence. The fence is adjustable for alignment with downstream equipment such as a Moulder. (3) lower powered feed rolls are smooth steel and non-marking. The feed rolls and chains are controlled by adjustable frequency drives. (3) upper pinch rolls are 5"; diameter urethane. The first (2) rolls singulate pieces while (1) pinch roll keeps the board moving on the bridge. The pinch rolls are triggered by photocells. A PLC in the control cabinet cycles the outputs based on operator input. Operator controls allow for start and stop of the chains and rolls, the feed to be paused, the rolls to be reversed and speed controls. -- Fabricated structural steel frame -- Passline height 42"; +/- 1"; -- Stock width 2"; to 9"; -- Stock Thickness 1/4"; to 4"; -- Stock Length 6’ - 16’ -- Rolls include a variable feed rate from 60 to 300 FPM -- Feed roll drive is by a 3 HP gearmotor -- (6) infeed chains, each 50"; long, are driven by a 1-1/2 HP gearmotor -- Infeed chain's variable feed rate is 20 to 75 FPM -- 2-1/2"; bore air cylinders actuate the pinch rolls -- With 3/4"; fence adjustment. ELECTRICAL CONTROLS: -- Controls are incorporated in the LCF Cabinet for the above Transfer System. It consists of operator controls, (2) VFDs, and additional PLC I/O and programming. STARTUP: -- 2-days startup assistance is included. Travel expenses are billed se

ROSE MACHINERY TRANSFER SYSTEM: PANEL RIPPER TO MOULDER INFEED OUTFEED TRANSFERA Rollcase will carry stock away from a LHI 72" Panel Ripper. When the stock reaches the far end-stop, a 6-Strand Transfer Belt will pop up and take the stock to a Lateral Chain Feeder (supplied by others). The lifting mechanism is triggered by photocells and powered by an air bag using plant air. When the stock clears the Rollcase, the transfer will return to the down position to receive the next batch of strips. Rollcase Specs:17' 0" long; 76" between frame; 1.9" dia. X 12 gauge rollers. Galvanized rollers are set high on 3" centers. 5-1/2" x 1-1/2" x 12 gauge formed steel channel frames; welded construction. 120 FPM maximum. Dual shaft w/jump chain; underhung drive; timing belt driven; 1 HP, 575 volt/3ph/60hz motor; less controls. With (3) H-style leg supports; 34" top of roller; adjustable 32" to 38", with knee braces. Fixed angle end-stop. Frame is powder coated blue; guards powder coated yellow. Transfer Specs:B/17 purple power twist belt; 36" strand centers; 10'-0" long. UHMW chain track; airbag lifting style; thru frame; 36" top of chain. With 1/2 HP Boston 575 volt/3ph/60hz motor with Boston reducer for 120 FPM; less controller; proximity switches to detect carriage position are mounted only; solenoid valve, mounted and plumbed; filter/regulator - mounted and plumbed. With central bearing lube. Frame is powder coated blue; guards powder coated yellow Electrical Controls:ROSE provides an Electrical Control & Cabinet that will control the above Outfeed Transfer System. Electrical Control will incorporate a fused disconnect for incoming power, transformer and power supply for control voltage, (4) variable frequency drives for the motors, a PLC to read input devices and control output devices, and pushbuttons/switches for operator control. The panel will be mounted and wired to the enclosed devices. Incoming power and other field wiring is by others. Two days startup assistance is included. Travel expenses will be billed at cost separately.Conditions:All gear-motors, mechanical equipment, limit switches, sensors or photoelectric devices as required for each item of this quotation, will be supplied and mounted. All pneumatic cylinders or other pneumatic power devices and their valves will be supplied and mounted. They will have connecting hoses and fittings installed. Filter/Regulator units will be supplied, mounted and connected by hose to the valves. Compressed air service to equipment is by others.Exclusions:This proposal describes the machinery to be provided by Rose Machinery Inc.. The equipment supplied by Rose Machinery Inc. is specifically limited to the items actually described in the itemized details of this quotation. Unless specifically mentioned herein, all other items and services are the responsibility of the Buyer. State or local sales taxes, or any permit or other fees that may be required are not included. All field wiring, plumbing, and installat

This item is in an Auction on exfactoryauctions.com. Go here to view item: http://exf.ac/i6s ROWLEY & HERMANCE Sash Sticking Machine Specifications: Table size 5” x 46”. Equipped with: 3 HP - 1,750 RPM Motor. (2) 2” Dia. x 2” W Serrated upper feed rollers.

// This item is up for Auction at exfactoryauctions.com // https://bit.ly/40zDLa2 RUVO Door Lite Cutout machine Model 9715W Specifications: 7' Max. door height x 3' max. door width; max. lite sizes in 3' door 30" x 60", 24" x 64", or 20" x 66"; lock sizes 1-1/2", 1-5/8" and 2-1/8". Deadbolt sizes 1-1/2", 1-5/8" and 2-1/8"; corner radius 1/4" for both lite and faceplates; backset switch selectable for 2-3/8" or 2-3/4". "Broken Arm" design for lite cut outs in wooden doors. Machines wood or steel doors (to 16 ga.) with 3 HP cutter head, 2-speed operation with 2,400 or 4,700 RPM; (2) horizontal stations, features door length adj. and end clamps. Equipped with: Boring for lock, deadbolt, and latch, (2) Back fences, steel hole template locating pin, template clamp, end clamp cylinders, flip stop assembly on the back fence. The 9700 control box provides the operator with exceptional versatility allowing independent operations for special house orders Recommended cutter head ONSRUD 15-05 cutting bit with reverse flute (interchangeable with EKSTROM-CARLSON bit 088-1680). Ruvo's 9700 Door Lite Cutter series machines are manufactured to last under heavy use and are the finest available to steel and wood door suppliers. The heavy-duty, easily operated cantilever cutting arm is key to the model's speed and efficiency. After the lite template and door are pneumatically clamped, its arm follows the template edge as a 1/2" cutter bores through the door.

RUVO 9715 Door Lite Cutout Machine. -- 80" Max. door height x 36" max. door width; configured for wood and steel doors.. -- Capacity Specifications: Max. lite sizes in 3' door 30" x 60" or 24" x 66", larger for 36" doors; lock sizes 1-1/2", 1-5/8" and 2-1/8"; deadbolt sizes 1-1/2", 1-5/8" and 2-1/8"; corner radius 1/4" for both lite and faceplates. -- Designed with the "Broken Arm" design for lite cut outs in wooden doors. -- Equipped with: 2 HP Cutter head, 2-speed operation with 2,400 or 4,700 RPM, (2) horizontal stations, door length adj. and end clamps. -- Complete with: (2) Back fences, steel hole template locating pin, template clamp, end clamp cylinders, flip stop assembly on back fence. -- Actual model is RUVO 9715S.

RUVO 2260 Wedge Cutter. -- General Data: Wedge and glue-block cutter. Allows for 1" X and 2" X material in the same hopper. Cuts (2) wedges out of 1" X material and (1) wedge out of 2" X stock. -- Self diagnostic system, walk-away, hands free operation. -- If not reloaded, the machine has an auto-shut-off feature at the end of the stack to prevent the machine from cycling endlessly. --With capability to cut glue-blocks. -- Ports for dust collection.

RUVO 505, ...Prehung Door Machine.Handles a wide range of door, jamb, and hinge sizes. - Bevels doors and door hinges. - Designed for efficient handling and operation. - Fast, accurate hinge and lock backset adjustment. - Residential, Commercial, Architectural, and Labeled Fire Doors.Features: Heavy duty powered 3° beveler/sizer. Routers to ease door edges. Accurate target scales. The 4-hinge and jamb route location changes fast and precisely. A similar system for the backset on hinges & locks. Provision for single and double-belled doors. Controls interlocked by a PLC. Auto door sizing is fast to adjust the lifter bar by digital input and servo control. Reliable, long-lasting non-contact sensors. Fast push-pull controls with a friendly touchscreen HMI. Hinge screw gun and pre-drill included.Technical Details: Max Door Height: 6’ - 9’ or ADA Specs 6’ - 8’. -- Door Width: 1'-6"’ to 4’. -- Door Thickness: 1-3/8"; to 2-1/4. -- Jamb Size and Styles: Up to 1-1/4"; x 10";, all styles. -- Number of hinges: Up to (4); Hinge Size: 3-1/2" to 5";; Hinge Radius 1/4" to 5/8". -- Hinge Backset: Scaled as required -- Lock Bore Sizes: 2-1/8"; Standard. -- Lock bore Backset: Scaled to 5";. -- Lock Bore Latch plate: Up to 1-1/4"; x 8";.Machine Size: 18’ x 3’ x 7’; Approx. Machine Weight: 3,200 Lbs; Electrical: 4-Wire, 230/3/60 and draws 25 Amps. Requires a 1/2" airline using 40 CFM @ 90 PSI.Options Include: -- Built-In Power Beveler Vacuum System......$ Please call. -- Screw Driver............................................... Included. -- Pre-Drill Kit.................................................. Included -- Digital Readout ..........................................$ Please call.RUVO 512, ...Heavy Duty Strike Jamb Mortising Machine.For Jam Sizes up to 1-1/4"; x 9"; x 10";. Strike Plate mortise to 6";. Compliments Jamb Preparation of the RUVO 505 and 405. Operated by one worker.Unit Includes: -- Adjustable Jamb Stops. -- Heavy Duty Construction. -- Foot Pedal Actuated Clamp. -- 120 Volt, 1-Phase, 20 Amps. -- 1/2" Airline needs 0.5 CFM @ 100 PSI. -- 1.5 HP Router.@ 23,000 RPM. Additional Cost for the RUVO 512 above ...$Please call.Material Handling for the Line:Loading Device..........................................$ Please call.Unloading Device.......................................$ Please call.

RUVO 2200 Stair Stringer Router, Top/Bottom, Semi-automatic with Stair Glue/Assembly Table. -- Size capacity (nominal): 2" Thick x 12" - 15-3/4" wide stringer size; semi-automatic operation. -- (2) 5 HP, 25,000 RPM Router motors for top & bottom heads. T & B heads are arranged to jump in & out to facilitate open plan stairs; automatic pneumatic clamping of stringers, spring loaded side pressure to keep stringers against the fence. -- Mirror-image routing on (1) pair of stringers at one time, graduated template automatically sets up to stated tread & rise, cuts standard wedge taper for both treads and risers. -- Includes: Clamp and feed system & safety covers. -- NOTE 1: Stair Router rebuilt in 2022 by BUILDERS AUTOMATION. Replaced 3HP with new 5HP routers. Reconditioned air cylinder pistons, air-over oil booster, replaced air lines, etc.. Painted from green to Blue. -- NOTE 2; Includes custom made Glue-up Clamp for Stair Assembly, as pictured.

--In auction: https://exfactoryauctions.com/Detail/SA-231010/event/A122024$1 --No Reserve!-- RYE R 72 2-Spindle Automatic Rotary Copy Shaper Specifications: Cutting circle cap. 24" - 80", Max. square cap. 56", Max. rectangular shape cap. 71" x 35-1/2", & Max. length capacity 50". Table size 68" Dia. x 40-1/2" H. Table speeds 0.3 - 3 RPM. Spindle speed 9,000 RPM. Equipped with: (2) 1-1/8” Dia. High frequency floating spindles, with Frequency changer. 6-1/2” Dia. Center clamp plate.

SAV S 53 S Single-Sided Planer20" Width x 1/8" to 12" opening; 6.6 HP motor, 4-knife 4-3/4" dia. cutter head rotates @ 5,000 RPM, max. cutting depth 5/16" -- (4) fixed feed speed settings 13 - 23 - 36 - 59 FPM. Equipped with: -- (1) Steel outfeed roller, (2) adjustable bed rollers, sectional infeed roller, sectional chip breaker, manual raise & lower w/mechanical digital readout; -- Table size 41" x 21". Complete with: -- Emergency stop, magnetic starter w/overload protection & 5-1/2" dia. dust hood.

SAC - PRIMA K 630, ...Single Head Sander24" Width cap single head. -- Combination sanding head with: 4-3/4" Dia. grooved rubber contact roll & 2" wide polishing platen. -- 7.5 HP Motor; abrasive belt size 25" x 75" with air tensioning & electronic abrasive belt tracking. -- Dual feed speed 15 or 31 FPM; infeed & outfeed rubber-covered holddown rolls. -- 6-1/4" Motorized thickness adjustment by 0.5 HP motor with: LED Readout, and automatic part thickness adjustment; micro switch; 7" dust hood opening. -- Complete with: --: Emergency stop button, motor load meter, and selection of belts.

SAC F 430 430 mm (16.93") Jointer Specifications: Max. depth of cut 8 mm (0.31"), Rabbeting cap. 1/3" x 16". Infeed table size 430 x 1,570 x 860 mm (16.93” x 61.81” x 33.86”) H. Outfeed table size 430 x 1,280 x 860 mm (16.93” x 50.39” x 33.86”) H. Cutterhead speed 5,000 RPM. Equipped with: 120 mm (4.72”) Dia. 4-Knife Nickel-Chromium Molybdenum Steel Cutterhead, with "TERSA" Knives. 3 kW (4HP) Motor, with Brake. 1,200 mm L x 160 mm H (47.24” L x 6.30” H) Aluminum fence, with 0° - 45° Tilt. Swing-away guard. Knife setting gage. Complete with: Spare Knife Set (Needs sharpening).

SIERRA - RB5000, ...Portable Baler/LoggerNew in 2011 - Less than 500 hoursFeatures and Specifications: -- Faster cycle times equals higher production volume. -- Features an easy-to-load loading box that opens to 16’-5"; x 8’-1"; and short-stroke rams that greatly reduce cycle times. These powerful rams crush each load with 240 tons of force per side, producing:Logging production: 16 - 22 Tons per hourBaling production: 10 - 14 Tons per hour -- The "RB5000" is the perfect machine for any scrap yard that receives appliances, sheet iron, smaller automobiles & automobile shells, clips, and busheling as their main source of material. -- The "RB5000" Portable Baler/Logger compresses logs and bales to shredder and mill specifications. -- Typical log density: 25 to 35 Lbs. per cubic foot. Average overall weight: 1400 lbs. -- Typical bale density: 80 to 90 lbs. per cubic foot. Average overall weight: 850 lbs. -- Any transfer station that receives a high volume of appliances and sheet iron can also greatly reduce freight costs by baling and logging. -- The structural details and proper design protect the key components of the "RB5000". -- The solid self-framed construction of this portable baler/logger includes SIERRA’s: Standard L-box shaped design, 11/16th-inch abrasion-resistant steel Hardox 450 liner plates, and outer honeycomb construction creating a greater box integrity and adding to the "RB5000’s" longevity. -- For added versatility, the Crane is independent of the Baler, has a continuous rotation, and is fully operational while the Baler/Logger is in use, increasing productivity. -- The Crane features 24-2/3 Ft. boom length and 4,400 Lbs capacity while fully extended and includes an orange peel grapple with a rotator that was specifically designed to handle bales and logs. The well-designed cab and agronomical controls were designed for comfort, safety, and long-term use.

SIERRA - 700T: Shear BalerSpecifications: -- Motors: (2) Electric 100 HP. -- Preload Table. -- Precompression. -- Shearing: 14 - 17 Tons per hour. -- Baling: 12 - 14 Tons per hour. -- Logging: 15 - 17 Tons per hour. -- Cylinders: (1) Main Compression ram; (6) folding box rams. -- Cylinder forces: Shear - 700 tons precompression; 115 tons main compression; 160 tons folding box; (6) cylinders @ 80 tons each; 240 tons each side. -- Folding Box Dimensions: 19 Ft. x 8 in. x 7-2/3 ft. Open: 19 Ft.; 8 in. x 32 in. x 24 in. Closed: 34 In. x 22 in.Shear Throat -- Disassembled approx. (3) years ago. -- Running when removed from service.

SIERRA T556SLK Shear/Baler/LoggerApproximately 3500 hours only!The T556SLK shear/baler/logger was designed with strength, mobility, and time efficiency. It is available diesel or electric and is a true workhorse that doesn’t require a special foundation. After a two-day assembly process, it is ready to work for you. Easily transportable, the SLK series can be easily taken from yard to yard, and there is no need for an operator as they come fully equipped with remote-control operation.With 556 tons of cutting force, the T556SLK Shear/Baler/Logger has unmatched versatility and is ideal for scrap processors, C&D facilities, and Demolition contractors.Shear:Foundry scrap, pipe, beams, plate, HMS #1, HMS #2Shearing production: 16 - 22 tons per hourBale:Clean sheet, wire, lightweight scrap, tin, clipsSize (31"; x 25 x Variable), Weight (900 lbs. average)Baling production: 16 - 22 tons per hourLog:Appliances, automobiles, sheet metal, tinSize (31"; x 25"; x Variable), Weight (1200 lbs. average)Logging production: 18 - 22 tons per hourAs with all Sierra machines, the T556SLK is expertly manufactured with an innovative L-Box-shaped design, 11/16th-inch replaceable abrasion-resistant steel HARDOX "450" liner plates, and outer honeycomb construction, creating greater box integrity.

SIERRA - RB6000, ...Portable Baler/Logger - New in 2020Approx 9,300 HoursThe RB6000’s automatic baling and logging cycles keep you at peak efficiency. Baling: 12 - 16 Tons per hourLogging: 18 - 22 Tons per hourAutomobile Logging: 26 - 32 Tons per hourThe RB6000 baler/logger is a beast on automobiles, appliances, and lightweight sheet iron; producing logs with the density you need to meet max weight. Looking to produce mil-spec bales?The RB6000’s cylinder comes within 18 inches of each other allowing you to densely bale clips and busheling to mill specifications.Average Bale and Log specifications:Bales: Size (40 in. X 24 in. X Variable), Weight (850 lbs.)Logs: Size (40 in. X 24 in. X Variable), Weight (1200 - 1400 lbs.)The portability of the RB6000 baler/logger gives you the versatility you need with the capability of being moved to multiple locations or to different areas within the same location.The hydraulic powered outriggers provide the needed stability to handle the heavy weight of the machine.

SIERRA - RB6000, ...Baler/Logger - New in 2008Electric with approx 12,500 hoursThe RB6000’s automatic baling and logging cycles keep you at peak efficiency. Baling: 12 - 16 Tons per hourLogging: 18 - 22 Tons per hourAutomobile Logging: 26 - 32 Tons per hourThe RB6000 baler/logger is a beast on automobiles, appliances, and lightweight sheet iron; producing logs with the density you need to meet max weight. Looking to produce mil-spec bales?The RB6000’s cylinder comes within 18 inches of each other allowing you to densely bale clips and busheling to mill specifications.Average Bale and Log specifications:Bales: Size (40 in. X 24 in. X Variable), Weight (850 lbs.)Logs: Size (40 in. X 24 in. X Variable), Weight (1200 - 1400 lbs.)