//This machine is in an Auction on exfactoryauctions.com// //Link to machine: http://exf.ac/i62 GRIZZLY G7214Z Shaper Specifications: 1-1/4" Dia. interchangeable spindle, 7.5 HP - 3,450 RPM motor; 3,600, 5,100, 8,000 & 10,000 RPM spindle speeds via 4-step V-pulley. 5-1/8" Cap. under nut when using the 1-1/4" spindle, 3-1/4" spindle travel, 34-3/4" x 35-1/2" cast iron table, 43" working height. Table Counterbore: 7" dia. x 5/8" deep Complete with: Adjustable Fence with integrated 4" dust collection shroud, reversing switch & magnetic controls, 3-roll power feeder

15" Width cap. with 1/4" - 8" thickness opening, 1/16" max. depth of cut; 3 HP single-phase motor belt drives 3-knife, 3-15/64" dia. cutter-head at 5,000 RPM; head with high-speed steel knives, max. thickness 8", min. 3/16"; dual feed speed of either 16 or 30 FPM; 16" x 42" cast iron table, table extensions on infeed/outfeed. Complete with: Magnetic controls, 2" dia. metal infeed & outfeed rollers, open fabricated steel base, and large hand wheel for cutter-head assembly adjustment.

GRIZZLY G4185 2-Spindle Horizontal Boring Machine, Will Accept 3-Spindle Boring HeadSpecifications: -- Max. stock width 7-1/2";. -- Table size 9-3/4"; x 15-3/4";, Max. table height 35";, Table height adjustment 3-1/2";. -- Max. bit cap. 9/16"; (Right-hand threaded), Spindle travel adjustment 3";, Spindle speed 4,000 RPM, Max. speed 12 SPM at 90 PSI. -- Hold-down force 600 Lbs.Equipped with: -- 2 HP 3,450 RPM TEFC Direct drive motor. -- Pneumatic spindle travel. -- 2-1/4"; Pneumatic hold-down. -- Pneumatic foot pedal control. -- Steel stand.Complete with: -- GRIZZLY "G5952"; 2C-W19"; 2-Spindle Boring Head, Max. bit cap. 5/8";, Bit threads 7/16 - 14 TPI Right-hand, Spindle speed 4,000 RPM.

GS - HEAVY-DUTY 34 KVA, ...Transformer.SCR Drive Transformer. -- Cat # DT631H34S. -- High voltage 575 Volts Delta; Low voltage 230 Y/133.

GUBISCH MODEL CP-230 4 HEAD PUSH FEED MOULDER: -- 4-Head (T-R-L-B), working capacity 6" x 4". -- Head sequence: Top 15 HP, right/left 15 HP and bottom 15 HP motor. -- Spindle dia. 1-13/16" all heads with cutterhead speed of 6,000 RPM on vertical spindles and 7,000 RPM on horizontal spindles. Heavy duty, built-in profile jointers on spindles #2, #3 and #4. -- Mechanical adjustment for spindle settings. Spindle adjustments from the front side of machine. -- Variable speed feed drive via 7-1/2 HP, variable speed motor with speeds from 16 to 120 FPM; with (2) powered rollers from the top and (2) powered rolls in the table. -- Infeed table;chromed table plates. --Pneumatic jointers on all 4 heads Amazingly well built Moulder; off-the-shelf parts accessibility; low maintenance/operating costs.

GUIDETTI - WIRE 415, ...Copper & Wire Chopper with Pre-Shredder -- Currently Disassembled.Specifications: -- Feed size of material; 1,310 x 2,140 mm. -- Load pusher stroke: 600 mm. -- Rotor diameter: 220 mm. -- Rotor rotation speed: 82 RPM. -- Hydraulic power: 0.75 kW. -- Grid hole diameter: 40 mm. -- Rotating blades: 23 + 4 External. -- Low hours; 2,300 Hrs.? -- Has not been used since 2015GUIDETTI Pre-Shredder New in 2012. -- Model: PM6N 600/200 -- Low hours: 1,700 -- Has not been used since 2015 -- Loaded onto your truck.

HAAS - 2000XL 2.0, ...Mobile ShredderLow Hours; 2018 YMFG.Specifications & Features: -- Can be used at any location (comfortable transport measurements). -- Easy & quick positioning thanks to crawler track and radio remote control. -- Shreds different materials with just (1) tool configuration. -- High throughput capacity of up to 100 tons/Hr. -- Resistant against foreign bodies. -- Low wear cost and long lifetime. -- Service and maintenance friendly. -- No wrappings; self-cleaning. -- Quiet main drive.

RAFIX - Futura 250: Hinge Boring & Inserting Machine with 1-1/2 HP MotorSpecifications -- High-quality air cylinder (80 mm bore with 650 ft. Lbs of pressure @ 90 PSI) rated for 3-1/2 million 3" strokes.A skilled Operator can bore & insert in (3 - 4) seconds. -- Features: (2) Types of boring depth adjustment: Drawbar style for quick and easy adjustment and a solid stop adjustment for the changing of door thickness applications. This allows changing of the door thickness and still bore the same depth without adjustment. -- Fixed table with: Adjustable back rail to control the tab location. -- Enclosed cutting area for better chip removal with blow off nozzle to assist in chip evacuation and adjustable 2" & 4" vacuum hookup. -- Pneumatic drilling unit with push button control. -- Includes: Adjustable cutting speed control; indicator light; reset thermal circuit breaker; emergency stop button; drill & insert buttons (2-hand activation for Operator safety); rotary switch for pair of pneumatic holddown clamps; 600 mm ruler & (4) flip stops.

HAMMEL 750D HAMMERMILL NEW IN 2019Approx 3,000 Hours --Hydraulic recycling machine with 2 slow running tool shafts --Suitable for Wood (Old wood, construction & demolition wood, rhizomes, green waste, pallets, cable drums) or Rubbish (Domestic waste, industrial and commercial waste) and Paper, paper rolls, aluminum profiles and balesAdvantages: --Increased performance for more throughput --low energy consumption --Very easy to maintain --User-friendly handling by IFM control --Better accessibility of the control panels --Low noise --Tilt funnel with increased inclination for optimum material flow --Mobile on a chain or semi-mobile on a hooklift

SPX FLOW HANKISON HPRN200 200 CFM Non-Cycling Refrigerated Compressed Air DryerSpecifications: -- Cap. 200 SCFM at 100 PSIG & 100° F. -- Max. working pressure 232 PSI. -- Max. inlet temperature 120° F -- Refrigerant type R-407C.Equipped with: -- 200 W (1/4 HP) Refrigeration compressor motor. -- Stainless steel cross flow heat exchanger. -- LED Dew point indicator. -- Dry alarm contact. -- Timed electronic drain valve.

SPX FLOW HANKISON HPRN200 200 CFM Non-Cycling Refrigerated Compressed Air Dryer Specifications: Cap. 200 SCFM at 100 PSIG & 100° F. Max. working pressure 232 PSI. Max. inlet temperature 120° F Refrigerant type R-407C. Equipped with: 200 W (1/4 HP) Refrigeration compressor motor. Stainless steel cross flow heat exchanger. LED Dew point indicator. Dry alarm contact. Timed electronic drain valve. CURRENCY NOTE: Negotiable Price is listed in U.S. Dollars.

HARMONY - S60-XDRC: Vertical BalerSpecifications: -- Motor: 20 HP. -- Bale Size: 30";x 60"; ≤ 48";. -- Bale Weight (OCC): Up to 1,000 Lbs. -- Feed Opening: 25″ x 60″. -- Ram Force: 92,360 Lbs. -- Volume: X-Large 7" cylinder. -- Loaded onto your Truck!

WOLVERINE Two Ram Auto Tie Baler with Infeed Conveyor --Cylinder replaced in 2018 --BALE SIZE Width 46"Height: 31"Length: 61" --BALE VOLUME cu.ft. 50 --CAPACITY cu ft./hour 10,975 --CHARGE BOX OPENING inches 41" x 60" --HOPPER OPENING inches 40-3/8" x 60" --MAIN PUMP 60 GPM --SYSTEM PRESSURE PSI 3500 --MAIN RAM FACE PRESSURE PSI 145 --EJECTOR RAM FACE PRESSURE PSI 84 --SHIPPING WEIGHT 20 TonsBALING MATERIALBulk OCCSolid WasteNewsprintWhole Aluminum CansSteel CansPlasticNon-FerrousHDPE

HARRIS PIRANHA Full Closed Door Horizontal BalerSpecifications: -- Cylinder: 10" -- Main motor: 20 HP -- Feed opening: 56" x 36"Equipped with: -- Full Pen

HARRIS HRB-SR 2-Ram Horizontal BalerBC-011225: -- Main motor: 100 HP -- Cylinder: 12" -- Bale size: 45" x 45" x 56" -- Force: 198 Tons -- Bale ejector bore: 8" -- Bale ejector force: 88 Tons -- Side ram bore: 6" -- Side ram force: 9 Tons

HARRIS-SELCO - HLO-608AR40: Open-End Auto-Tie Horizontal Baler -- Motor: 40 HP. -- 8" Cylinder with: 80" Stroke. -- Infeed opening; 45" x 60". -- Bale size: 48" x 40" x Variable. -- Bale weight: Up to 1,800 Lbs (OCC). -- Production capacity: Up to 6 T/Hr. -- Shear blade. -- Platen force 113,100 Lbs. -- Completely refurbished. -- Warranty: (180) Days Parts/Labor Warranty. -- Loaded onto your truck.

HARRIS/SELCO - HLO-60AREB: Horizontal Auto-Tie Baler -- Motor: 2 – 100 HP. -- Cylinder: Rebuilt 12″. -- Hopper: 80″ Long. -- Hours of Operation: 14,000. -- Tons Per Hour/OCC: Up to 26 Tons. -- Includes 72″ MAYFRAN Steel Belt Feed Conveyor.

SELCO - HSO-170AR30: Auto-Tie Baler• 20 HP Motor.• 7"; Main Cylinder.• Bale Size: 30"; x 36"; x (variable).• Cycle Time (No Load): 23 Seconds.• Main Ram Face Pressure: 74 PSI• System Pressure: 2,250 PSI.• Total Compression Force: 86,590 Lbs.

HASKO HSEM & HSFM End Matcher High-Speed Feed Through; Complete with Infeed conveyor, Transfer conveyor, End matcher, Outfeed conveyor and All ToolingSpecifications: -- The feed-thru system allows for continuous feeding of random length parts with any kind of profile. -- Width cap. 1" x 7"; length cap. 8-1/2" x 12'-0" lengths; 5/16"- 2" max. thickness cap.; -- Endmatcher with feed speed from 12 - 154 lugs per minute. -- Infeed powered roller conveyor 12" x 16', feeding singulator wheels for introducing lumber onto 9-strand infeed chain deck for the Endmatcher. -- Chain deck allows for spacing of boards for singulation between the spacing bars on the infeed deck system feeding the right-hand & left-hand stations. -- Infeed to tongue cut 19'-4" x 10', Crossover chain 14' x 10' to groove cut, outfeed chain 24'-0". Transport sprockets 50 pitch.Equipped with: -- Tongue first position and groove second; (3) heads per station all with VFD 5 HP motors at 6,000 RPM. -- Both the right and left-hand processing stations have a scoring, trim and profiling head. Includes: -- (One) Auxiliary infeed 8' x 7" ABC for infeed to Tongue unit with 3/4 HP variable speed drive -- (One) Auxiliary outfeed conveyor 13'-6" long x 7" wide slider belt with 3/4 HP variable speed drive to be installed behind the groove unit and extends out for grading station.Tooling: 12" in diameterNote: Specifications must be verified Still under power.

--AT AUCTION-- HEESEMANN KSA 8 CSD 80" Lacquer/Sealer Sander This is a Very Special "extra wide" HEESEMANN equipped with: HEESEMANN's patented "CSD" selective pressure adjustment system, sensors placed every 5/8" (16 mm) sense part configuration; pressure for each segment can be preprogrammed to provide less pressure on the outer edges, or more in the center if desired. The "CSD" computer control will hold a max. of (20) programs. Equipped with: Segmented Polishing Platen: Segments are computer controlled to conform to irregular shaped panels; sanding pressure on panel edges is adjustable. Platen will accept panel thickness variation up to 5/64" (2 mm). Dual speed motor: 26 & 31 kW (35 & 42 HP); abrasive belt speed: 10 + 20 MPS (33 + 66 FPM); abrasive belt size: 2,050 mm x 3,250 mm (80.7" x 128"); pneumatic air tension and tracking control. 250 mm Dia. Rotary Panel Cleaning Brush, 5 HP motor, 150 mm Outfeed Rotary Panel Cleaning Brush, and 2 HP motor. Additional Features: Vacuum bed assembly to ensure flatness of parts and feeding of small parts. Computer control and monitor, light indication of panel movement; electronic abrasive belt tracking. Feed System: Variable feed speed from 5 - 15 MPM (16 - 49 FPM); 4 kW (5 HP) feed motor; motorized thickness opening. NOTE: This Sander had a "Brand New" ...$ 17,000 display/control installed shortly before it was taken out of service in 2016. The machine has been in storage since that time.