TERCO NORTHSTAR 10-8 Spindle Carver.8-Spindle Carver with 10" center-to-center chuck spacing. -- (2) 0.5 HP - 3,450 RPM spindle motor direct "belt drives" spindles for 11,000 RPM rotation. -- 36" Long carving cap, with optional length extensions up to 72". -- Manual rotation for round parts. -- Operator manually traces the pattern details of the master with copying stylus. -- Capable of doing both base relief (flat backed) and 360° full round carving. -- Includes: (1) Set roughing bits, (2) sets finishing bits, tools, and manual.

THERMWOOD CS 40 CNC Router, 4 X 8 with ATC:Under power for inspection!4' x 8' Moving table machine in a front-to-back configuration with single-zone vacuum plenum. -- Equipped with:(1) 10 HP HSD, ISO-30 type routing spindle, variable spindle speed from 3,000 - 24,000 RPM, 5-position "typewriter-style" ATC mounted on the front of the spindle, and (4) position wine rack at rear of table. -- Features:High-performance closed loop SEIMENS AC Servo motors driving precision ball screws on all axes with TURBO motion for feed speeds up to 2,400 IPM on the X- & Y-axis and 600 IPM on the Z-axis. -- Control:THERMWOOD "91000" PC Based control with WINDOWS/2000 operating system, 3-axis simultaneous motion, handheld programmer with feed rate & spindle speed override. -- Features:Color monitor, large hard drive, CD ROM drive, 3-1/2" floppy disk drive, keyboard, RS-232 port for PC communications, mounted in an air-conditioned Nema-rated control cabinet, E-CABINET software ready. -- Complete with: 18 HP BECKER vacuum pump, assorted tool holders, and documentation.

Timesavers 2321-45-01 (2) Head wide Belt Sander51" Width cap, Drum, Combination HeadHead Configuration1st Head: Steel contact roll, 8" dia., 30 HP motor.2nd Head: Combination head with a rubber-covered contact roll 5-1/2" dia. and 2-1/2" wide segmented finishing platen, 25 HP motor, (2) dial indicators for contact roll height adjustment.Specifications: 52" x 103" Abrasive belts, -- "Posi-Trak" electronic tracking & pneumatic tensioning, conveyor belt feed. -- 15 - 45 FPM Variable feed speed with inverter control, -- Automatic conveyor belt tracking; -- Double in-feed & out-feed spring loaded hold-down rolls.Equipped with & Features -- 0" - 5" Max. motorized part thickness opening with automatic part thickness set-up, -- Air-operated disc brakes, -- Motor load meters, -- 14" in-feed conveyor area, -- In-feed emergency stop bar."Owner's manual included

TIMESAVERS BM24-2 Wood Brush Sander. One 24" sanding brush is followed by a second brush for finish or sealer sanding. -- Includes MASTER SAND (1) set of hubs and brushes. -- Drives: 7.5 HP Variable Speed Drives on each head. 1 HP Variable Mechanical feed drive. Feed speed is adjustable from 10 - 40 FPM. -- Features: Spring-Loaded holddown rolls that can feed min. 12" long parts. Rough-top conveyor belt. (2) dust outlet connections at 4" dia. requiring about 450 CFM each.Other Specifications: -- Sanding wheel diameters: 11" rotating at 200 - 1,200 RPM. -- Feed/Passline height variable: 29 - 34.5" -- Maximum workpiece width: 24". -- Maximum workpiece height: 5.5". Minimum thickness: 0.200" -- Dust collection required: 900 CFM. -- Machine dimensions/Weight: 58" Long, 48" wide, 52" high. 925 Lbs. -- Electrical Load: 21 Amps @ 460/3/60.

TIMESAVERS 43- 3 OB Orbital Sander3-Head, 43" width cap. with (2) Orbital heads and (1) finishing brush. -- 1st & 2nd Orbital Heads: Each orbital head with (1) 10" wide platen for a total of (2) platens, each platen features a "dual action" head with a high-speed orbit and combined back-and-forth oscillation to remove abrasive belt cross-grain scratches. -- "Quick change" system for abrasive material, (2) 7.5 HP main orbit motors, and 1 HP oscillation motor. 3rd Head: Rotary abrasive brush with 2 HP motor, single side brush wear/height adjustment. -- Conveyor belt feed with Ruff-Tex conveyor belt, variable feed speed from 5 - 20 FPM, infeed & outfeed holddown pinch rollers on all heads. -- 0" - 6" Motorized part thickness opening, constant pass line-height of conveyor bed assembly, extended infeed load area, motor load meters on sanding heads. -- Includes a DOUCET Return Conveyor System -- New transformer for 230 or 460 Volt, specifically for this machine is available at an additional cost

TIMESAVERS 137-1HD WIDE BELT SANDER0" to 8" Thickness cap. (1) Head, 36" width cap., combination sanding head with 4" dia. contact roll & 1.5" wide polishing platen. --Equipped with: -- 20 HP main drive motor. -- Abrasive belt size 37" x 60". -- Pneumatic abrasive belt tensioning, and tracking with POSI-TRACK electronic abrasive belt sensors. -- Variable feed speed motor 15 - 45 FPM via 1.5 HP TEFC motor. -- Double infeed & outfeed rubber covered holddown rolls. --Complete with: Infeed conveyor extension with safety stop bar and motor load meter.

Timesavers 2311-24-6 Pro V.42″ Segmented Platen, Wide Belt Sander42″ Segmented Platen, Specifications: -- 3,273 hours. So it is not a high hour machine. -- 42″ width X 4.75″ (120 mm) thickness capacity. -- Controlled via an easy to use touchscreen. -- Stores up to 240 Programs. --Font drum is a 5″ helically grooved rubber drum that is pneumatically actuated from the control panel. -- The head has variable speeds from 275-1,150 RPM. -- The platen is segmented and there is NEW graphite on the platen.Equipped with & Features -- Both the platen and head have dial indicators for fast, easy, accurate control over adjustments. -- Rear of the machine you will find dust sweeps. -- Up top you will also find a pneumatic air wand for abrasive cleaning. -- Cleaning brush. -- On the front center of the machine you will find an auto calibrating unit. -- The vacuum bed has a 15 hp blower with an almost NEW feed mat. -- The feed mat is driven by a 2 hp motor that is VFD controlled allowing for 12-45 FPM.

TIMESAVERS 150-1v Wide Belt Sander;1-Head, 50" width cap.; contact roll head with 40 HP motor; 50" x 103" abrasive belt size, air tracking, 2-1/2" max. thickness cap., adjusted by scale; variable feed speed 40 to 100 FPM; incl. in- & outfeed extension. -- Used to have a checkrail edge sanding attachment for sanding sash (no longer available), but includes (1) extra set of new conveyor belts.

TIMESAVERS 137-1 SINGLE HEAD WIDE BELT SANDERSpecifications: -- 36" Width capacity, combination sanding head with 6" dia. spiral grooved rubber contact roll. -- 1-1/2" Wide adjustable height polishing platen on slide out assembly. -- 37" x 60" Abrasive belt size.Equipped with: -- 20 HP Main motor, -- Electric eye abrasive belt tracking, and limit switch monitoring. -- 1 HP feed motor with a fixed speed of 30FPM. -- 0" - 8" manual part thickness opening of conveyor bed. -- Double infeed & outfeed rubber covered holddown rollers. Complete with: -- 18" Infeed conveyor extension, motor load meter, and safety stop bar.

TIMESAVER - 113, ...12" Width Single-Head Wide Belt Sander12" Width cap., single drum.Specifications: -- 12" Width capacity. -- 7.5 HP Main motor. -- 6" Dia. drum. -- 0 - 8" Opening capacity. -- 0.5 HP Feed motor. -- Complete with: Posi-Trac electronic tracking and a 12" conveyor extension.

TIMESAVERS - 352 HDA, ...Abrasive Planer/Sander2-Head, 51" width cap. Heavy Duty Sander. -- 1st Head: Smooth steel contact roll, 11-1/2" dia., 75 HP motor. -- 2nd Head: Spiral Grooved hard rubber contact roll (11-1/2" dia.) , 75 HP motor; 52" x 103" abrasive belts (6,300 & 4,300 SFPM) with POSI-TRAK electronic tracking. Equipped with: -- Heavy-Duty solid rubber (no vacuum holddown) feed belt for Heavy-Duty operation. -- Motorized part thickness adjustment, 0" - 6" opening. -- 38" - 32" Conveyor height passline with MITUTOYO LED readout, conveyor belt feed. -- 5 HP Variable feed speed from 20 - 60 FPM, smooth rubber conveyor belt. -- Infeed & outfeed spring loaded holddown shoes, infeed emergency stop bar, anti-kickback fingers on infeed. -- Disc brakes on sanding head motors, 18" infeed load area, and motor load meters on sanding heads.

TiMESAVERS - 237-KA IC, ...Planer Sander w/2-HEADs 2-Head Planer Sander Combination; 37" width capacity.Head Configuration: -- 1st Head. 7" Dia. Helical "Quiet Cut" planer head with: (6) Spirals of 4-sided carbide inserts with 15° rake angle; head turns @ 3,200 RPM; head adjustment with dial indicator readout; 30 HP motor. -- 2nd Head. Combination Sanding head with: 6" Dia. contact roll (60 - 65 Duro) and 2-1/2" wide finishing platen; 25 HP motor; sanding head with: 37" x 75" abrasive belt with "POSI-TRAK" electronic tracking.Feed System: -- Variable feed speed 15 - 45 FPM; automatic conveyor belt tracking; 3-ply rough top conveyor belt. -- Anti-kickback fingers on infeed; air loaded sectional shoe with dial indicator adjustment; double grooved pinch roll on infeed of knife head. -- Infeed & outfeed pinch rolls on sanding head; air activated caliper disc brakes on all heads. -- Motorized part thickness adjustment of 0" - 6" with digital readout.Complete with: -- Controls mounted on belt loading side; main motor fuse protection on both heads; load meters for each head; "over thick" shutoff system; 24" infeed conveyor extension.

TIMESAVER 337-2 Wide Belt Sander, (2) Heads36" Width cap., Drum, Combination HeadHead Configurations:1st Head: 11-1/2" Dia. spiral grooved rubber contact roll 40 HP motor.2nd Head: Combination Head, Drum with Platen 30 HP motor. Specifications -- 37" x 75" Abrasive belts with pneumatic tracking. -- 2 HP feed drive; Variable feed speed from 20 - 60 FPM.Equipped with & Features -- Infeed & outfeed spring loaded holddown rolls on both heads. -- Motorized thickness adjustment with indicator, -- 0" - 6" opening. -- Infeed safety stop -- Adjustable shoes before and after each head. -- Controls mounted on belt loading side, --Sanding head motors with air caliper disc brakes, and motor load meters.

TIMESAVERS 252-4-IC, ... Wide Belt Sander, 4-Head.4-Head, 51" cap. - Great sander for solid wood and veneer panels equipped with (2) Contact rolls and (2) Air platens. Head Configuration1st Head: Rubber covered contact roll, 9-1/2" dia. 60 - 70 Durometer, 40 HP motor.2nd Head: Rubber covered contact roll, 9-1/2" dia. 50-60 Durometer, 30 HP Motor.3rd and 4th Head: Finishing platens, 2-1/2" wide "Veneer Saver" inflateable platens with adjustable timers for leading and trailing edges, 20 HP motor each head.Specifications: -- 38" Constant pass line height of Vacuum conveyor with suction fan and motor bed assembly for veneer and solid wood sanding. -- Adjustable air floating infeed and outfeed hold down shoes. -- 52" x 103" abrasive belts with "POSI-TRAK" electronic tracking.Equipped with & Features: -- Motorized part thickness adjustment with mechanical digital readout. -- Auto part thickness set-up, 0" - 6" opening. -- Hydraulic feed belt operation of 15 - 45 FPM via 7-1/2 HP hydraulic pack. -- 4-Motor load meters, controls mounted on belt loading side. -- Disc brakes on sanding head motors. -- 30" Infeed load area.

TIMESAVERS 237-4IC Four-Head Wide Belt Sander37" Width cap. Drum, Drum, Drum, PlatenHead Configuration:1st Head: Rubber covered contact roll, 9-1/2" dia., 30 HP motor;2nd Head: Rubber covered contact roll, 9-1/2 " dia., 25 HP Motor. 3rd Head: 9-1/2" Grooved Rubber Covered Contact Drum With A 20 HP Motor4th Head: Finishing platen, 2-1/2" wide, 20 HP motorSpecification -- 37" x 75" abrasive belts with Pneumatic tracking. -- Motorized part thickness adjustment, height, 0" - 6" opening. -- Automatic part thickness adjustment, -- Infeed & outfeed spring loaded holddown shoes, -- Variable feed speed from 15 - 45 FPM, 5 HP motor. -- Pneumatic feed beltEquipped with & Features: -- Motor load meters, -- Infeed emergency stop bar, -- Controls mounted on belt loading side, -- Automatic Trabon bearing lubrication system, -- Disc brakes on sanding head motors, -- 30" infeed load area.Note: Some spec's need to be verified

TIMESAVER - TB-440-4, ...2-Head Wide Belt Sander40" Width cap.; Drum and Combination Head.Head Configuration:1st Head - 50 HP; 12" rubber covered contact head.2nd Head - 40 HP; combination platen head.Specifications: -- Sander completely rebuilt (15) years ago. -- Rubber covered abrasive rolls were recovered, grooved and balanced, along with ALL pinch rolls recovered at FLETCHER MACHINE CO., Lexington, NC. -- Electric eyes upgraded to BANNER's send and receive type; includes battery backup system for controls (no crashes when machine has power outage). -- Feed speed gear box driven by AC Drive controlled 10 HP motor. -- Rebuild included: Table removed and platens ground flat; all bearings replaced, including pinch rolls and tracking cylinders; tension cylinders plasma sprayed, reground & new factory seal kits. -- Entire machine was disassembled, sand blasted and DUPONT "Zolatone" primed and painted. -- RAINBOW brand feed conveyor belt replaced in 2014. -- Many more upgrades, too many to list: Please contact for additional information. -- Machine is in good condition, running daily, and has had regular recommended service intervals; includes all factory manuals, blueprint drawings, parts list with numbers supplied, and when machine was new. -- Machine used in solid wood wide belt sanding. -- Includes Cloth aluminum Oxide Belts: 7 - 50 grit; 1 - 60 grit; 8 - 80 grit; 2- 120 grit; 8 -1 80 grit..

TIMESAVER 237-3 IC Wide Belt Sander: 3-Head, 36" cap. - Drum, Drum, Finishing Platen. -- 1st Head: Rubber covered contact roll, 11-1/2" dia., 50 HP motor; -- 2nd Head: Finishing platen 2-1/2" 30 HP motor. -- 3rd Head: Finishing platen 2-1/2" wide, 30 HP motor. Specifications: -- 37" x 75" Abrasive belts. -- "POSI-TRAK" electronic sanding belt tracking. -- Motorized part thickness adjustment. -- 0" - 6" Opening, automatic part thickness adjustment. -- Infeed & outfeed spring loaded holddown shoes. -- Variable feed speed from 15 - 45 FPM, 5 HP feed motor.Additional Features: -- Motor load meters. -- Infeed emergency stop bar. -- Controls mounted on belt loading side. , -- Disc brakes on sanding head motors. -- 30" Infeed load area.Actual model: TIMESAVERS "237-3IC"

TIMESAVER - 337-2, ...2-Head Wide Belt Sander36" Width cap., Drum & Combination HeadHead Configurations:1st Head: 11-1/2" Dia. spiral grooved rubber contact roll 40 HP motor.2nd Head: Combination Head, Rubber contact Roll & Platen 30 HOSpecifications: -- 37" x 75" Abrasive belts with pneumatic tracking. -- 2 HP Feed drive; Variable feed speed from 20 - 60 FPM. -- Infeed & outfeed spring loaded holddown rolls on both heads. -- Motorized thickness adjustment with indicator, 0" - 6" opening. -- Infeed safety stop bar. - Also has adjustable shoes before and after each head. Equipped with & Features: -- Controls mounted on belt loading side. -- Sanding head motors with air caliper disc brakes --Motor load meters.

TIMESAVERS 52-20 ORBITAL SANDER2-Head, 52" width cap. with (2) Orbital heads.Specifications: 1st & 2nd Orbital Heads: Each orbital head with (2) 5" wide platens, each platen features a "dual action" head with a high-speed orbit and combined back-and-forth oscillation to remove abrasive belt cross-grain scratches. -- 1st Head: 7.5 HP 230/460V 3PH motor -- 2nd Head: Oscillating platen 7.5HP, 330/460V, 3Ph"Quick change" system for abrasive material -- Conveyor belt feed with Ruff-Tex conveyor belt, variable hydraulic feed speed from 5 - 20 FPM, vacuum bed assembly, infeed & outfeed holddown pinch rollers on all heads. -- 0" - 6" Motorized part thickness opening with mechanical digital readout, constant pass line of conveyor feed bed assembly, motor load meters on sanding heads -- Push button controlsNOTE: Feed Motor and Feed Belt have been taken apart for shippingThe above specs are taken from literature and considered accurate. As always please take advantage of the inspection period to verify.

TIMESAVERS 2331-04-334 DUAL HEAD DENIBBING SANDER2-Head, 42" width capacity Sanding / Denibbing system. -- (2) 5" Wide platens featuring a "dual" action head with a high-speed orbital movement and combined back & forth oscillation to remove abrasive belt cross-grain scratches; platens designed with a quick change system for abrasive material. -- (1) Nylon abrasive impregnated (150 grit) Cleaning / De-Nibbing brush, 10" dia., drive unit for brush rotation, brush wear adjustment via jack screws. -- Vacuum holddown conveyor system with variable feed speed 5 - 15 FPM. -- Double infeed and outfeed holddown pinch rollers. -- Power raising and lowering of the conveyor bed with AUTO-SET feature, 0" to 6" part thickness capacity. (4) DUFF-NORTON acme screw jacks under conveyor bed, 36" infeed conveyor area.....below in the comments see what the current owner says: