TIMESAVER - TB-440-4, ...2-Head Wide Belt Sander40" Width cap.; Drum and Combination Head.Head Configuration:1st Head - 50 HP; 12" rubber covered contact head.2nd Head - 40 HP; combination platen head.Specifications: -- Sander completely rebuilt (15) years ago. -- Rubber covered abrasive rolls were recovered, grooved and balanced, along with ALL pinch rolls recovered at FLETCHER MACHINE CO., Lexington, NC. -- Electric eyes upgraded to BANNER's send and receive type; includes battery backup system for controls (no crashes when machine has power outage). -- Feed speed gear box driven by AC Drive controlled 10 HP motor. -- Rebuild included: Table removed and platens ground flat; all bearings replaced, including pinch rolls and tracking cylinders; tension cylinders plasma sprayed, reground & new factory seal kits. -- Entire machine was disassembled, sand blasted and DUPONT "Zolatone" primed and painted. -- RAINBOW brand feed conveyor belt replaced in 2014. -- Many more upgrades, too many to list: Please contact for additional information. -- Machine is in good condition, running daily, and has had regular recommended service intervals; includes all factory manuals, blueprint drawings, parts list with numbers supplied, and when machine was new. -- Machine used in solid wood wide belt sanding. -- Includes Cloth aluminum Oxide Belts: 7 - 50 grit; 1 - 60 grit; 8 - 80 grit; 2- 120 grit; 8 -1 80 grit..

TIMESAVER 237-3 IC Wide Belt Sander: 3-Head, 36" cap. - Drum, Drum, Finishing Platen. -- 1st Head: Rubber covered contact roll, 11-1/2" dia., 50 HP motor; -- 2nd Head: Finishing platen 2-1/2" 30 HP motor. -- 3rd Head: Finishing platen 2-1/2" wide, 30 HP motor. Specifications: -- 37" x 75" Abrasive belts. -- "POSI-TRAK" electronic sanding belt tracking. -- Motorized part thickness adjustment. -- 0" - 6" Opening, automatic part thickness adjustment. -- Infeed & outfeed spring loaded holddown shoes. -- Variable feed speed from 15 - 45 FPM, 5 HP feed motor.Additional Features: -- Motor load meters. -- Infeed emergency stop bar. -- Controls mounted on belt loading side. , -- Disc brakes on sanding head motors. -- 30" Infeed load area.Actual model: TIMESAVERS "237-3IC"

TIMESAVER - 337-2, ...2-Head Wide Belt Sander36" Width cap., Drum & Combination HeadHead Configurations:1st Head: 11-1/2" Dia. spiral grooved rubber contact roll 40 HP motor.2nd Head: Combination Head, Rubber contact Roll & Platen 30 HOSpecifications: -- 37" x 75" Abrasive belts with pneumatic tracking. -- 2 HP Feed drive; Variable feed speed from 20 - 60 FPM. -- Infeed & outfeed spring loaded holddown rolls on both heads. -- Motorized thickness adjustment with indicator, 0" - 6" opening. -- Infeed safety stop bar. - Also has adjustable shoes before and after each head. Equipped with & Features: -- Controls mounted on belt loading side. -- Sanding head motors with air caliper disc brakes --Motor load meters.

Timesavers 2321-45-01 (2) Head wide Belt Sander51" Width cap, Drum, Combination HeadHead Configuration1st Head: Steel contact roll, 8" dia., 30 HP motor.2nd Head: Combination head with a rubber-covered contact roll 5-1/2" dia. and 2-1/2" wide segmented finishing platen, 25 HP motor, (2) dial indicators for contact roll height adjustment.Specifications: 52" x 103" Abrasive belts, -- "Posi-Trak" electronic tracking & pneumatic tensioning, conveyor belt feed. -- 15 - 45 FPM Variable feed speed with inverter control, -- Automatic conveyor belt tracking; -- Double in-feed & out-feed spring loaded hold-down rolls.Equipped with & Features -- 0" - 5" Max. motorized part thickness opening with automatic part thickness set-up, -- Air-operated disc brakes, -- Motor load meters, -- 14" in-feed conveyor area, -- In-feed emergency stop bar."Owner's manual included

TIMESAVERS BM24-2 Wood Brush Sander. One 24" sanding brush is followed by a second brush for finish or sealer sanding. -- Includes MASTER SAND (1) set of hubs and brushes. -- Drives: 7.5 HP Variable Speed Drives on each head. 1 HP Variable Mechanical feed drive. Feed speed is adjustable from 10 - 40 FPM. -- Features: Spring-Loaded holddown rolls that can feed min. 12" long parts. Rough-top conveyor belt. (2) dust outlet connections at 4" dia. requiring about 450 CFM each.Other Specifications: -- Sanding wheel diameters: 11" rotating at 200 - 1,200 RPM. -- Feed/Passline height variable: 29 - 34.5" -- Maximum workpiece width: 24". -- Maximum workpiece height: 5.5". Minimum thickness: 0.200" -- Dust collection required: 900 CFM. -- Machine dimensions/Weight: 58" Long, 48" wide, 52" high. 925 Lbs. -- Electrical Load: 21 Amps @ 460/3/60.

TIMESAVERS 43- 3 OB Orbital Sander3-Head, 43" width cap. with (2) Orbital heads and (1) finishing brush. -- 1st & 2nd Orbital Heads: Each orbital head with (1) 10" wide platen for a total of (2) platens, each platen features a "dual action" head with a high-speed orbit and combined back-and-forth oscillation to remove abrasive belt cross-grain scratches. -- "Quick change" system for abrasive material, (2) 7.5 HP main orbit motors, and 1 HP oscillation motor. 3rd Head: Rotary abrasive brush with 2 HP motor, single side brush wear/height adjustment. -- Conveyor belt feed with Ruff-Tex conveyor belt, variable feed speed from 5 - 20 FPM, infeed & outfeed holddown pinch rollers on all heads. -- 0" - 6" Motorized part thickness opening, constant pass line-height of conveyor bed assembly, extended infeed load area, motor load meters on sanding heads. -- Includes a DOUCET Return Conveyor System -- New transformer for 230 or 460 Volt, specifically for this machine is available at an additional cost

TIMESAVERS 52-20 ORBITAL SANDER2-Head, 52" width cap. with (2) Orbital heads.Specifications: 1st & 2nd Orbital Heads: Each orbital head with (2) 5" wide platens, each platen features a "dual action" head with a high-speed orbit and combined back-and-forth oscillation to remove abrasive belt cross-grain scratches. -- 1st Head: 7.5 HP 230/460V 3PH motor -- 2nd Head: Oscillating platen 7.5HP, 330/460V, 3Ph"Quick change" system for abrasive material -- Conveyor belt feed with Ruff-Tex conveyor belt, variable hydraulic feed speed from 5 - 20 FPM, vacuum bed assembly, infeed & outfeed holddown pinch rollers on all heads. -- 0" - 6" Motorized part thickness opening with mechanical digital readout, constant pass line of conveyor feed bed assembly, motor load meters on sanding heads -- Push button controlsNOTE: Feed Motor and Feed Belt have been taken apart for shippingThe above specs are taken from literature and considered accurate. As always please take advantage of the inspection period to verify.

TIMESAVERS 2331-04-334 DUAL HEAD DENIBBING SANDER2-Head, 42" width capacity Sanding / Denibbing system. -- (2) 5" Wide platens featuring a "dual" action head with a high-speed orbital movement and combined back & forth oscillation to remove abrasive belt cross-grain scratches; platens designed with a quick change system for abrasive material. -- (1) Nylon abrasive impregnated (150 grit) Cleaning / De-Nibbing brush, 10" dia., drive unit for brush rotation, brush wear adjustment via jack screws. -- Vacuum holddown conveyor system with variable feed speed 5 - 15 FPM. -- Double infeed and outfeed holddown pinch rollers. -- Power raising and lowering of the conveyor bed with AUTO-SET feature, 0" to 6" part thickness capacity. (4) DUFF-NORTON acme screw jacks under conveyor bed, 36" infeed conveyor area.....below in the comments see what the current owner says:

TORIT - 460-IRD-20: Dust CollectorAn easy and economical solution for a wide range of wood dust collection applications. Downflow air pattern allows airflow & gravity to move filtered dust to collection receptacles for longer bag filter life and reduced pressure drop.Specifications -- 20 HP Direct drive; floor mounted blower. -- Fan inlet: 17". -- CFM: 7,000. -- Set of filter bags. -- Steel elbow from fan to collector. Motor Starter included.

Automatically feeds, shapes & ejects Rosette blocks in sizes from 5-1/2" - 8" max. square blocks; 3 HP motor belt drives 4-3/4" spindle cutterhead @ 7,500 RPM. -- Operation: Adjustable hopper feed to side of spindle automatically indexes Rosette blocks under cutterhead up against a corner-V holding fixture with overhead spring fingers, cutterhead advances and machines Rosette, then automatically ejects block to front (hydraulic position of block and air eject cylinder). -- Features: Cutterhead equipped for standard 16°/60° corrugated back 1/4" thick knives to be ground at 0° hook angle. -- Produces up to (500) Rosettes/Hr; Rosette profiles can be ground on any profile grinder for infinitely variable design possibilities; table top unit may include base.

MINNESOTA 24-8 Multi-Spindle Carving Machine.Specifications: -- Spindles/Capacity: (24) Spindles, 8" between centers & 72" length capacity. -- Motors: (12) 0.75 HP motors with (1) motor driving (2) spindles via flat belt. -- Features: Manual table elevation, motorized stock rotation, non-indexable head. -- Comes with: (2) Sets of carving tools (one medium and one fine). -- Includes: Tables for flat carving - to be confirmed (?).

MOAK - NO. 7, ...Spindle ShaperSpecifications: -- 1.5 HP motor, belt driven to spindle; 9,000 RPM spindle speed; 1" diameter spindle. -- Length of spindle above table is 5"; 3-1/4" vertical adjustment of spindle; 22" x 42" table; manual starter; 750 Lbs machine weight.

MOLDOW Style, by ' NEU-JKF', Modular Baghouse with chain-sweep bottom feeding into a Rotary Air Lock (RAL) at the end of filter bank. -- General Data: Approx 35,600 CFM running at a 5:1 Air-to-Cloth Ratio. Total of 7,125 sq. ft. of filter area comprised of (14) modules each containing (27) filter bags. Filter bags are 8.5" dia. by approx. 96" long. All modules including inlets are fitted with filter bags. -- Main fans: Total of (3) Material Handling (MH)fans. (2) NORTHERN BLOWER Size 23, Des 5691, CL 3 Fans each belt driven by 60 HP TEFC motor. Fan inlets supplied by 26" dia. pipes. (1) type JK 25 HP MH blower. -- Filter Cleaning: Each module is supplied with a 2 HP approx. regenerative high pressure fans to sequentially back-flush the dust from the bags during operation and thereby falling into the continuous hopper with a drag-chain-sweep mechanism that rides along the bottom of hopper and feeds into the RAL. -- Return Air: All modules are ducted into one return air manifold pipe. -- Electrical Controls: CONQUEST free standing electrical control panel with visual light indicators for monitoring system status. Panel contains all start/stop pushbuttons and selector switches, and main disconnect. -- Includes: Steel Support frame with a walkway to the access doors which can act as explosion vents. Full set of polyester filter bags. -- Inquire for a cost for professional dismantling and transportation.

MOLDOW 184 MXN-324 Expandable Baghouse - 18 Total Modules with (4) Inlet Sections. Specifications. -- 72,000 CFM modular/expandable unit, currently with (14) Filter sections @ 5,000 CFM per section (24 bags per section). -- Approx 336 filter (8.6" dia. by 120" long) , 9,300 sq. ft. of total filter media, 7.75:1 air to cloth ratio Shell is under negative pressure allowing a high efficiency clean air fan.. -- Main Fan: Air Handling IAP A600 SWSI, Class IV, S/N 26862-1 rated at 90,000 CFM @ 1321 RPM, 16.0/20.3" SP & 290/308 BHP. Fan is A - Airfoil type wheel & is non-overloading powered by MARATHON "445Ta" belt driven TEFC 300 HP motor.. Currently fan inlet is connected with a 30" pipe. Regenerative Filter Cleaning: -- Each row of filter bags is cleaned continuously during operation by use of a regeneration carriage/trolley rides along top of filter bank) with a 4 KW (5.3 HP) high-pressure fan that sends air from the clean-air chamber back through the filter bags using nozzle pipes.Bags are fitted with an inner spring bracing. Special bag design reduces air velocity which increases air and dust loading considerably. -- Equipped with: Built-in bottom drag link chain which brings dust to one end where it is discharged through approx. 9" x 30" Rotary Air Lock (RAL). Currently a transfer fan moves dust to storage bin.. Summer/Winter Diverter/Abort Gate connected on outlet/return air line.Comes with: -- Relay Fan, IAP 911 RBO, to pneumatically convey collected dust at discharge of RAL. -- Platform with safety railings and ladder to access regeneration cabinet (return air plenum). -- Interior electrical control panel, support frame, and exterior ductwork. Single heavy sheet metal flanged rectangular return air pipe. Overall Dimensions: -- 45' Long by 12'-9" wide by 28.5' high (5.5' hopper to ground, 8' high hopper and 15' top section). -- Professional dismantling, rigging, transport and installation is available upon request.

MORBIDELLI UNIFLEX HP 1.1 CNC MACHINING CENTER (2-HEAD): -- Specifications:Flexible "TOP & BOTTOM" Machining Center that uses an innovative panel handling system. -- Positioning SpeedsThe "UNIFLEX" can reach positioning speeds of: 130 MPM in "X" Axis; 80 MPM in "Y" axis; 50 MPM in "Z" axis with total safety, providing an unmatched working capacity. -- Working DimensionsMax. worktable part size for: "X" axis is 118" (3,000 mm); "Y" axis is 51" (1,300 mm) "Z" axis max. part thickness 3.1" (80 mm).Min. worktable part size for: "X" Axis is 7.8" (200 mm); "Y" axis 2.7" (70 mm); min. part thickness 0.157" (4 mm). -- Worktable:Automatic LH infeed air table with gripper clamps; automatic RH outfeed transfer conveyor with belts; both infeed & outfeed are considered Robot ready. -- Boring Units:(1) Top mounted boring block: 4.2 HP (3 kW); variable speed from 1,500 - 6,000 RPM; (48) vertical spindles: 24-Spindles in "X axis & 24-spindles in "Y" axis; (6) horizontal spindles with: (2+2) in "X" axis & (1+1) in "Y" axis; (1) 4.2 HP (3 kW) - 9,000 RPM, NC controlled 0°-90° "X/Y" Grooving Saw, max. 120 mm dia. blade.(1) Bottom mounted boring block: 4.2 HP (3 kW); variable speed from 1,500 - 6,000 RPM; (48) vertical spindles: 24-Spindles in "X axis & 24-spindles in "Y" axis; (6) horizontal spindles with: (2 + 2) in "X" axis & (1 + 1) in "Y" axis; (1) 4.2 HP (3 kW) - 9,000 RPM, NC controlled 0°-90° "X/Y" Grooving Saw, max. 120 mm dia. blade. -- Machining:(1) Top mounted 10 HP (7.5 kW) electro-spindle with: HSK D-50 Adaptor; "ERC 32" tool holders & RC-32 collets, 1,500 - 24,000 RPM.(1) Bottom mounted 10 HP (7.5 kW) electro-spindle HSK D-50 adaptors, "ERC 32" tool holders & RC-32 collets; 1,500 - 24,000 RPM. -- Operator Interface:PC Front-End with: "XYLOG PLUS" + Windows environment Operating system; 20 GB hard drive; 17" TFT monitor; international keyboard, soft touch keypad & industrial mouse; RS-232 Serial ports, USB ports; (1) 1.44 MB floppy drive; (1) CD ROM drive; all mounted in separate control console. -- Operating System:"XYLOG PLUS" Offers Real time multitask processing; programs can be transferred via diskette or downloaded by wire. -- Complete with: Pneumatic part clamping devices; sound enclosure; safety mats. -- Operating features: Machine can work the panel from above & below at the same time and can produce (2) identical or mirrored panels per cycle with no difficulty.The "UNIFLEX" can machine porous materials since the pieces are held with grippers, directly managed by the numerical control; it can even process small pieces and carry out "through" machining.(4) Operating modes at each cycle, it can change automatically from: Top machining to bottom machining, to top & bottom machining together, either on (1 or 2) stacked panels. -- Actual model is MORBIDELLI UNIFLEX HP.

MORBIDELLI AUTHOR 503 FT CUSTOM CNC MACHINING CENTER (W/ATC): -- Specifications:4' x 8' Custom Stationary Extruded Aluminum Table for "Nested Base" manufacturing;Working cap. "X" axis is 125.2" (3,180 mm), "Y" axis is 41.3" (1,050 mm) for routing "Z" axis stroke is 5.7" (144 mm); max. material thickness is 3.1" (80 mm) -- Positioning speed:"X " & "Y" axis is 213 FPM. (65 MPM), "Z" axis is 82 FPM (25 MPM). -- Work Table: 4' x 8' Custom Stationary Extruded Aluminum Table for "Nested Base" manufacturing;(2) pneumatic side stops, (2) working areas -- Machining Units:(1) 10 HP (7.5 kW) Vertically mounted electro-spindle router with ISO-30 adapter, LH & RH rotation, inverter driven from 12,000 - 18,000 RPM,(1) 5-position ATC tool rack mounted on the LH side for automatic tool change, -- Operator & Machine Control:Separate control cabinet with Morbidelli "TRIA 7500" CNC Multi-processor, VGA monitor, ergonomic keypad, 3-1/2" disk drive, and (2) serial ports RS-232 & RS-242.Offers incredible list of functions from (a) auto-diagnostic to (z) zooming; -- Complete with: Voltage stabilizer 208. 230, 460 V, 60 Hz, 3 Phase Auto Transformer (1) 100 m³/Hr vacuum pump. -- Actual model is MORBIDELLI AUTHOR 503 FT CUSTOM

MORBIDELLI AUTHOR M400 FR FLAT TABLE MACHINE(W/LOADING/RAKE/OFFLOADING): -- Specifications:5' x 12' Stationary extruded aluminum "MATRIX" table for "Nested Base" manufacturing with "Rake" and "Automatic Off-Loading Conveyor".Loading/working/processing direction is from LH (facing to RH (facing). -- Work Area:"X" Axis 143.7" (3,650 mm), "Y" axis 62.9" (1,600 mm), "Z" axis stroke 11" (280 mm), max material thickness is 6.69" (170 mm). -- Positioning Speeds:"X" & "Y" Axis 279 FPM (85 MPM), "Z" axis 98 FPM (30 MPM).Closed loop AC servo drive system with Precision Rack/Pinion in "X" axis & recirculating ground ball screw in the "Y" & "Z" axis.All axes ride on precision prism linear guideways. -- Work Table:5' x 12' Aluminum grid "MATRIX" vacuum table machined with a square grid pattern for fixturing parts, grid pattern allows use of vacuum pods or closed cell rope gasket material and use of spoil boards.(9) Independent, NC controlled working zone areas; external pop-up reference pins located on the sides & back of the table for positioning parts. -- Boring Unit "F37L2":3 HP (2.2 kW) - variable speed up to 7,000 RPM motor; F37L2 Boring Block with (24) Vertical spindles with (10) independent vertical spindles in "X" axis & (14) spindles in "Y" axis.The 10-spindle "X" axis boring unit is NC controlled with a 11.5" (293 mm) "Y" adjustable spread from its home position & independently controlled according to the drilling pattern being performed, this feature is IDEAL for high-speed line hole drilling.(12) Horizontal spindles with (4+4) in "X" axis on the programmable Independently NC controlled 10-spindle vertical boring unit, & (2+2) on the 14-spindle boring unit in "Y" axis. (1) NC controlled 0° - 90° "X" / "Y" Grooving Saw for max. 120 mm dia. blade. -- Machining:(1) 16.5 HP (12 kW) "Power 2000" Electro spindle w/lifetime lubrication and HSK F63 adaptor, NC controlled spindle speeds from 900 - 18,000 RPM.(1) 16-position "Rapid-16 traveling ATC tool plate for "on the fly" ATC NC Touch-off Probe for automatic Tool Length setting. -- Operator & Machine Control,PC Front End with XILOG PLUS + Windows "7" operating system. 17" high resolution LCD flat screen; ergonomic keypad.USB Ports, serial ports RS-232 & RS-242 & Ethernet adaptor.Programs can be transferred via USB or downloading by wire is possible; all computer components are mounted on a mobile stand. -- "XILOG Plus" offers incredible list of functions from: (a) Auto-diagnostic to (z) zooming; controlled acceleration & deceleration; encoder feedback; dynamic tool correction via PLC due to active tool wear using space-and-time criteria. -- Additionally equipped with: Onboard mini-CAD with built-in programming for writing circles, ellipses, & angles with only a few keystrokes.Onboard cycle optimization; onboard calculator; mirror-imaging and repeat imaging; all electronics mounted in an air conditioned, dust-free environment control cabinet. -- Complete with:(3) 300 m³/Hr "BECKER" Vacuum pumps;

MORBIDELLI N 100 15 FLAT TABLE MACHINE (W/ATC/BORING/RAKE): -- Specifications: 5' x 12' x 37" H High-efficiency laminate aluminum with Magnetic vacuum locking system.Grid pattern allows use of vacuum pods or closed cell rope gasket material & use of spoil boards for nested base machining, Part location pop-up pins mounted on table perimeter, Chips conveying device. -- Working Area: X-Axis 3,686 mm (145.12"), Y-Axis 1,555 mm (61.22"), Z- Axis 150 mm (5.91"). -- Travels:X-Axis 4,230 mm (166.54), Y-Axis 1,985 mm (78.15"), Z-Axis 250 mm (9.84"). -- Positioning Speeds: X- & Y- Axes 35 MPM (114 FPM), Moving Gantry, High precision rack & pinion system for X & Y Axes, Ground ball screws for Z-Axis, All axes ride on extra-large precision profile linear guide ways. -- Boring Unit: 2.2 kW (3 HP) Motor, (12) Independent vertical roto-axial spindles with (8) in X-Axis & (4) in Y-Axis, Maximum spindle speed 8,000 RPM. -- Machining: (1) 15 kW (21 HP) Air-cooled electro spindle with HSK F63 Adaptor, Variable spindle speeds to 24,000 RPM, (1) 14-Position TR side tool changer. -- Operator Interface:Mobile console with Integrated PC “EYE-M"; Industrial PC with 21-1/2" Full HD Multi-touch color touchscreen, WINDOWS Operating system, "MAESTRO SUITE" with Auto-diagnostic to Zooming, Controlled acceleration & deceleration, Encoder feedback, Dynamic tool correction via PLC due to active tool wear using space-and-time criteria, "TECPAD" Remote pendant with 7" Color touchscreen. -- Complete with: PRO-SPACE safety system which allows worktable access to all sides of the machine, (1) 300 m³/Hr. Vacuum pump, Automatic lube system, -- NOTE: Machine was de-installed by a technician and is currently in storage.

MORBIDELLI AUTHOR 636 FLAT TABLE MACHINE (W/ATC/RAKE): -- Specifications:5' x 12' Stationary extruded aluminum "MATRIX" table for "Nested Base" manufacturing. -- Work Area:"X" Axis 144" (3,660 mm); "Y" axis 57.8" (1,470 mm) for routing & 48" (1,230 mm) for boring; "Z" axis stroke 11" (280 mm); max. material thickness is 7" (180 mm). -- Positioning Speeds:"X" & "Y" Axes 262 FPM (80 MPM); "Z" axis 74 FPM (22.5 MPM).Closed loop AC Servo drive system with: Recirculating ground ball screw in the "X", "Y" & "Z" axis; all axes ride on precision prism linear guideways. -- Worktable:Aluminum grid "MATRIX" vacuum table machined with: Square grid pattern for fixturing parts;, grid pattern allows use of vacuum pods or closed cell rope gasket material and use of spoil boards.(2) Independent working areas; external pop-up reference ins located on the sides & back of the table for positioning parts. -- Boring Unit:3 HP (2.2 kW) - dual speed 4,500 & 6,000 RPM motor; (12) vertical spindles with: (7) spindles in "X" axis & (5) spindles in "Y" axis.(6) Horizontal spindles with (2 + 2) in "X" axis & (1 + 1) in "Y" axis. -- Machining:(1) 15 HP (11 kW) "Power 2000" Electro-spindle w/lifetime lubrication and HSK F63 adaptor; spindle speeds from 900 - 18,000 RPM.(1) 12-position "Rapid-12" traveling ATC tool plate for "on the fly" ATC. -- Operator & Machine Control:PC Front End with: NUM 1040 + Xilog III + Windows Operating System.Includes: 12" High resolution CRT, ergonomic keypad, 1.44 MB & CD ROM disk drives, (2) serial ports RS-232 & RS-242. All housed in air-conditioned cabinet with a KELVIN air conditioner. -- Complete with:(2) 250 cbm BECKER "VTLF 250" Vacuum pump with: Emergency stop rope, handheld pendant control. -- Options Include:Nesting Rake: Off feed table to increase machine/operator output; (1) 208/230/460 Volt transformer. -- Actual model - MORBIDELLI AUTHOR 636 S.

MORBIDELLI U 550 CNC MACHINING CENTER (W/ATC/BORING): -- Specifications: Worktable area "X" axis 126" (3,200 mm); "Y" axis 51" (1,300 mm),;"Z" axis stroke 4.52" (115 mm); max. material thickness 3.1" (80 mm). -- Positioning Speed:"X" & "Y" Axes are192 FPM (58 MPM); "Z" axis 80 FPM (24 MPM). -- Worktable:(8) Adjustable panel supports with (3) vacuum pods per support.(8) Pneumatic backstops, (2) pneumatic side stops & (2) pneumatic center stops; (2) independent work zones. -- Boring Unit:(1) 4 HP (3 kW) - 4,000 RPM Motor; (29) independent vertical spindles at 32 mm centers with (14) vertical spindles in "X" axis & (15) vertical spindles in "Y" axis.(6) Horizontal spindles with (3 + 3) in the "X" axis. -- Machining:(2) 9 HP (6.7 kW) Routers with: ISO 30 Adaptors; variable speed from 12,000 - 18,000 RPM.(1) 5-Position tool racks mounted on the LH side of the machine base for ATC. -- Operator & Machine Control:Separate control cabinet with: "TRIA 7500" CNC 32-Bit multiprocessor (100% MS/DOS compatible), 512 KB user RAM.14" VGA Color monitor; ergonomic extended keypad with (18) function keys; 1.44 MB floppy disk drive & (2) RS 232 & (1) RS 242 serial ports. -- Complete with:(1) 100 cbm/Hr Vacuum Pump; working head safety enclosure; emergency stop rope. -- Actual Model is: MORBIDELLI - U 550.