KREG DK 3100 Electric 3-spindle Pocket DrillSpecifications: -- 1.5 HP Direct drive electric motor; 39-1/2" table/ top working height; (0.5 - 1) Sec cycle time. -- Drills (2) pocket holes in (1) machining cycle across rails of varying widths with 3/8" dia. step bit in (1) smooth operation. -- Drill spindles in the machine are fixed at 3/4" - 1" and 1-3/4" on center allowing it to handle most common rail widths of 1-1/2" up to 3-3/4" with ease. -- One of the (3) Spindles is with left-handed, simply remove one bit from the spindle not being used to set the desired 2-hole spacing. -- The bits are supported all the way to the workpiece by a hardened steel drill guide that ensures tear-out free holes and consistent placement in virtually any material.Features: -- 15ø Boring angle for greater stability, reduced screw breakout & splitting. This produces a smaller "flat-bottom" pocket hole with rounded sides that can be plugged with a dowel if desired.Includes: -- Pressure gauge, fence, hold down, and foot pedal control.

KREG KFT 4X8 Face Frame Assembly. -- American-Made 4' x 8' Frame Assembly Clamp with floor stand. -- Working surface at approximately 30° angle for convenience. -- Unit includes; (4) Overhead air cylinders mounted on an overhead beam adjustable up-and-down. -- Clamping beam that moves from left-to-right by means of rollers. -- Squaring bars (fences) on the bottom and both ends of the table. -- Clamping beam with an air filter/oiler/regulator and air outlet at lower end of the beam. -- Optional pneumatic screw gun & pneumatic flex hose.

KREG DK 5100 5-Spindle Pneumatic Pocket Hole Machine. -- Individually actuated motors, (5) 0.75 HP motors, mounted on 6" centers. -- Hardened steel drill guides to support drill bit through the operation; 1-touch, foot pedal cycle. -- Swings stops for optimized material positioning; dust collection chutes for efficient chip removal. -- Complete with pre-filter and automatic lubricator.

Kremlin AIRMIX 15C25 Spray Pump perfect for painting small quantities of fluid products, water or solvent-based. Up to 90 bar of fluid pressure to compensate pressure drops.Specifications: -- (2) 5-gallon stainless steel covers/agitators, 3-way mixing valve for easy change-over, including hose. -- Pressure Ratio 15/1, Maximum Fluid Pressure 90 (1305) bar (psi), Maximum Air Pressure 6 (87) bar (psi) -- Air Consumption 2.8 (1.65) m³/h (cfm) -- Maximum Temperature 60 (140) °C (°F) -- Weighted Sound Level 71.2 dBA -- Recommended Air Pressure 2 - 5 (29 - 72.5) bar (psi) -- Fluid Output at 30 cycles/mn 0.75 (0.2) l/min (gal/mn), Fluid Output at 20 cycles/mn 0.5 (0.13) l/mn (gal/mn), Fluid Volume per Cycle 25 cc -- Free Flow Rate 1.5 (0.39) l/mn (gal/mn) -- Fluid Output at 15 cycles / mn 0.375 (0.01) l/mn (gal/mn) -- Air Consumption at 30 cycles/mn at 4 bar (60 psi) 2.8 m³/h (cfm), Displacement Per Cycle 25 (1.52) cc (cubic inch) -- Motor Type 245-4 -- Air Inlet F3/8 BSPP, Fluid Outlet F 3/8 NPS / M1/2'' JIC, Fluid Inlet F 1/2 BSPP / M26x125 -- Number of Cycles per liter of products 40 -- Height 57.5" x Width 32" x Depth 17", Weight 7.7 Lbs

Single belt oscillating "Tiltable Bed" 0° - 90° sander, 3 HP main motor, 3,400 RPM, belt size 6" x 89", 30.5" long platen. -- Max sanding length 30.5", 4" vertical adjustment of front table, 36" table height, oscillating rate of 121 times/min. -- Includes: (4) interchangable spindles, sizes are 1.25" - 1.5" - 2" & 2.5" dia.

Oscillating Edge Sander with end sanding kit. -- 6" Wide x 89" long abrasive belt. -- Tilting 6" x 24" platen. -- 3 HP, single or 3-Phase motor w/emergency switch. -- 6" Diameter drive pulley. -- 8" x 24" Front table with a 4" vertical adjustment and miter gauge. -- End table for radius work. -- Heavy tables, fabricated steel base and dust hood. -- 3-Phase unit model # is SK-3000SDN3.

KUFO SK-12RS Straight Line Rip Saw w/Return Conveyor;Entry level Straight-Line Rip Saw with a guaranteed 6' glue line. -- Powered by a 15 HP direct drive motor. -- 12" Dia. Blade capacity for up to 3-1/4" max. cutting height, 4,200 RPM blade speed. -- Equipped with (6) holddowns and a Wye-Delta soft start for lower amp requirements during start-up. -- 1 HP Feed motor, 36 - 145 FPM feed speed, 6" chain width and automatic chain lubrication. -- Treated chain links, pins and raceways withstand heavy use because of an automatic oiler. -- Large 15-3/4" rip capacity. -- Overarm control box mounted on the in-feed side. -- Total space requirements are about the same as a standard size tablesaw. -- Complete with side mounted return conveyor.

KUFO LS-500E Self-contained Dust CollectorDesigned for use in industrial environments for extracting different kinds of dust and dry shavings from single or multiple dust sources. It can be installed directly without any additional fire or explosion protection measures.Features: -- 5 HP Direct drive blower with backwardly curved blades and 2,649 CFM air flow rating; Inlet dia. 10". -- The blower is located on the clean air side. -- Noise reduction cover to reduce from 82 dB. to 76 dB. -- Fire control system with built-in Fire Sprinkler featuring auto-temperature activation (requires a water line hook-up). -- Pulse-jet filter cleaning with compressed air. -- (1) Dust collection tank container.Options: -- Built-in Fire Extinguisher with auto temperature activation -- "Y" Adapter with 9-3/4" inlet opening with 4" x (5) fitting -- Noise Reduction option (76 dB from 82 dB without).

KUFO LS-1000E Self-contained Dust CollectorDesigned for use in industrial environments for extracting different kinds of dust and dry shavings from single or multiple dust sources. It can be installed directly without any additional fire or explosion protection measures.Specifications: -- 10 HP Direct drive blower with backwardly curved blades and 5,239 CFM air flow rating; Inlet dia. 12". -- 5 Micron Top Filters -- Blower is located on the clean air side. -- Top sound reduction cover at 83 db from original 90 db. -- Fire control system with built-in Fire Sprinkler featuring auto-temperature activation (requires a water line hook-up). -- Pulse jet filter cleaning with compressed air. -- (2) Dust collection tank containers.Options: -- Built in Fire Extinguisher (2) with auto temperature activation. -- "Y" Adapter with 9-3/4" inlet opening with 4" x (5) fitting.

KUFO UFO-104D Dust Collector4-Bag self-contained free-standing unit (4 up & 4 down, all cloth), 23-3/4" dia. bags. -- Features: 4,167 CFM, 10 HP Motor. -- Bottom mounted 6-manifold inlet branch with (6) 4" inlets connect to a 9.5" dia. inlet; available as option: manifold with (5) 5" dia. inlets. -- Complete with: (4) Upper filter bags 2.5 micron and (4) lower cloth collector bags 2.5 micron, lower collector bags have 21 cu. ft. storage cap. each (84 cu. ft. total) -- Equipped with: Push button starter, base is mounted on (4) swivel casters.

KUFO UFO-103H Dust Collector. With 1-micron dust filtration efficiency this collector will make your shop cleaner, healthier, and more productive. -- (3) Fabric filter top bags are mounted above individual plastic collection bags. -- The multi-bag system is placed on sturdy steel legs in a horizontal series. -- 3,125 CFM Output with single-stage blower. -- Heavy Duty 5 HP motor with push button control and motor starter. -- 14" Steel blower fan impellers are dynamically balanced. -- Collection bag snap-in rings for easy installation and removal of bags. -- Filter bags filter out dust particles down to (1) Micron in size; 6 mil thick plastic bottom collection bags are standard.

KUFO UFO-103HC Modular Dust Collector - Cartridge filtration dust collection system.The "V" weave of the cartridge filter features up to six times more filtering area than standard filter bags. -- (3) Cartridge units are mounted above individual plastic collection bags. -- The multi-bag system is placed on sturdy steel legs in a horizontal series. -- 3,433 CFM Output with single-stage blower. -- Additional filtration sections can be easily added. -- Heavy Duty 5 HP induction motor. -- Steel blower fan impellers are dynamically balanced. -- Collection bag snap-in rings for easy addition or removal of plastic bags. -- 1-Micron 19" x 30" cartridge filters with 6 mil plastic bottom collection bags are standard. -- Cartridge filters are equipped with internal rotating cleaning scrapers actuated by manually turning a handle positioned at the top of each unit. Height 96". -- Optional upgrade to (3) 39.5" tall Canister Filters.

KUFO UFO-105DC Cartridge Dust Collector. (4) Upper cartridge filter, (4) Bottom bags, 7.5 HP motor, 4,900 CFM. -- Equipped with: Bottom mounted 5-manifold inlet branch with (5) 4" inlets connect to a 8-1/2" dia. inlet. -- Push button starter mounted to base with (4) swivel casters. -- Upper cartridges 19-1/2" x 39-1/2", filler material 1 micron Polyester. Bottom bags 19-1/2 x 31" plastic bags (4) ea. -- Unit is pre-wired 220 V.

KUFO UFO-104HT Dust Collector4-Bag self-contained free-standing unit (2 up & 2 down, all cloth), 23-3/4" dia. bags. -- Features: 4,238 CFM, 10 HP Motor. -- Bottom mounted 6-manifold inlet branch with (6) 5" inlets connect to a 9.5" dia. inlet. -- Complete with: (2) Upper filter bags 2.5 micron and (2) lower cloth collector bags 2.5 micron, lower collector bags have 21 cu. ft. storage cap. each (42 cu. ft. total) -- Equipped with: Push button starter.

KUFO UFO-104H2 Dust Collector. -- Includes; Heavy Duty 10 HP induction motor with 6,627 CFM single-stage collection system. (16) upper filter bags, 1-Micron @ 48" height and (4) lower collector bags, 59-1/2 cu. ft. total cap. -- Steel impellers that are dynamically balanced. -- Deflection baffles and bag hooks. -- Factory pre-wired at 220 V. -- Option; Change to 440 V.(Installed dimensions - 155" L x 32" D x 135" H)

KUFO UFO-104H1 Dust Collector. Radial-finned 8-bag Dust Collector. -- 6,627 CFM single-stage collection system. -- Heavy Duty 10 HP induction motor. -- Steel impellers that are dynamically balanced. -- Deflection baffles and bag hooks. -- 30-Micron 23-3/4" bag filters. -- Ready to operate with (8) upper filter bags and (2) lower cloth collector bags. -- Plenty of storage space with (2) bottom bags holding 29-3/4 Cu. ft.(Installed dimensions - 91" L x 32" D x 135" H)

KUFO UFO-105D Dust Collector 8-Bag self-contained free-standing unit (4 up & 4 down, all cloth), 23-3/4" dia. bags. -- Features: 3,812 CFM, 7.5 HP Motor, bottom mounted 5-manifold inlet branch with (6) 4" inlets connect to a 8" dia. inlet; available as option: manifold with (4) 5" dia. inlets. -- Complete with: (4) Upper filter bags and (4) lower cloth collector bags, lower collector bags have 21 cu. ft. storage capacity each (84 cu. ft. total). -- Equipped with: Push button starter, base is mounted on (4) swivel casters.

KUNDIG DUPLEX 53-RC-E Wide Belt Sander (2) Heads; 52" Width cap. Drum, Combination Head.Head Configuration1st Head: 7-1/4" Dia. rubber covered contact roll, 25 HP motor.2nd Head: Combination head with rubber covered contact roll and segmented finishing platen, infeed sensors sense the panel and electronically control the platen height with timers, variable edge control can also be set, 20 HP motor.Specifications: Abrasive belt size 54" x 75" with air tensioning and electronic abrasive belt tracking, both heads with abrasive grit thickness adjustment, 2 HP Variable feed drive. -- Conveyor belt speeds 9 - 45 FPM, controlled by electronic inverter & adjustable on the control panel; infeed & outfeed rubber covered holddown rollers.Equipped with & Features: -- Workpiece thickness cap. 1/8" - 6-1/4", motorized thickness adjustment with LED readout. -- A joystick controls the conveyor opening and start/stop of the feed, automatic "over-thickness" protection and automatic conveyor belt tracking. -- Constant passline of conveyor height at 35". -- Air blow off of second head abrasive belt. -- Emergency stop button, motor load meters, magnetic controls.NOTE from the seller: There is a small leak in the air bladder . The sander has 6,541 working hours

MORBIDELLI AUTHOR 504 R CNC MACHINING CENTER (W/ATC/BORING): -- Specifications: Working Cap. "X" Axis 139-3/8" (3,540 mm); "Y" axis 48-3/8" (1,230 mm) for routing & 39.6" (1,008 mm) for boring; "Z" axis 3.1" (80 mm). -- Positioning Speed:"X" Axis 213 FPM; "Y" axis 131 FPM; "Z" axis is 65 FPM. -- Worktable:(8) Adjustable panel supports each with: (3) Vacuum pods; worktable setup for (2) independent working areas. -- Boring Unit:(29) Independent vertical boring spindles forming a T-configuration with: (15) Spindles on the "X" axis and (14) spindles on the "Y" axis.A total of (8) horizontal spindles with: (3 + 3) on "X" Axis; (1 + 1) on "Y" axis. -- Machining:(1) 9 HP (7 kW) Vertically mounted router; inverter driven (FUJI) at 12,000 - 18,000 RPM.(1) 8-Position ATC for Automatic Tool Changer. -- Operator & Machine Control:"NUM CN" Loaded onto a HP, PC Based Controller mounted in separate control cabinet.15" VGA Color monitor and ergonomic keypad. Remote Control Pendant: Allows the operator to move around and still control all the axis movements, speed, and emergency stop.Includes: USB Ports; (2) serial ports RS-232 & RS-242 (requires no 3rd party CAD system for downloading programs). XILOG-PLUS OPERATOR Interface: Offers incredible list of: Functions from (a) Auto. diagnostic to (z) zooming; controlled acceleration & deceleration, encoder feedback, dynamic tool correction via PLC due to active tool wear using space-and-time criteria; programs can be transferred via diskette or downloaded by wire. Equipped with: Onboard mini-CAD with built-in programming for writing circles, ellipses & angles with only a few keystrokes; on-board cycle optimization, on-board calculator, mirror imaging, and repeat imaging. -- Complete with:(1) 100 cbm/Hr Vacuum Pump. -- Actual model is: MORBIDELLI - Author 504 .

MORBIDELLI UNIFLEX HP 1.1 CNC MACHINING CENTER (2-HEAD): -- Specifications:Flexible "TOP & BOTTOM" Machining Center that uses an innovative panel handling system. -- Positioning SpeedsThe "UNIFLEX" can reach positioning speeds of: 130 MPM in "X" Axis; 80 MPM in "Y" axis; 50 MPM in "Z" axis with total safety, providing an unmatched working capacity. -- Working DimensionsMax. worktable part size for: "X" axis is 118" (3,000 mm); "Y" axis is 51" (1,300 mm) "Z" axis max. part thickness 3.1" (80 mm).Min. worktable part size for: "X" Axis is 7.8" (200 mm); "Y" axis 2.7" (70 mm); min. part thickness 0.157" (4 mm). -- Worktable:Automatic LH infeed air table with gripper clamps; automatic RH outfeed transfer conveyor with belts; both infeed & outfeed are considered Robot ready. -- Boring Units:(1) Top mounted boring block: 4.2 HP (3 kW); variable speed from 1,500 - 6,000 RPM; (48) vertical spindles: 24-Spindles in "X axis & 24-spindles in "Y" axis; (6) horizontal spindles with: (2+2) in "X" axis & (1+1) in "Y" axis; (1) 4.2 HP (3 kW) - 9,000 RPM, NC controlled 0°-90° "X/Y" Grooving Saw, max. 120 mm dia. blade.(1) Bottom mounted boring block: 4.2 HP (3 kW); variable speed from 1,500 - 6,000 RPM; (48) vertical spindles: 24-Spindles in "X axis & 24-spindles in "Y" axis; (6) horizontal spindles with: (2 + 2) in "X" axis & (1 + 1) in "Y" axis; (1) 4.2 HP (3 kW) - 9,000 RPM, NC controlled 0°-90° "X/Y" Grooving Saw, max. 120 mm dia. blade. -- Machining:(1) Top mounted 10 HP (7.5 kW) electro-spindle with: HSK D-50 Adaptor; "ERC 32" tool holders & RC-32 collets, 1,500 - 24,000 RPM.(1) Bottom mounted 10 HP (7.5 kW) electro-spindle HSK D-50 adaptors, "ERC 32" tool holders & RC-32 collets; 1,500 - 24,000 RPM. -- Operator Interface:PC Front-End with: "XYLOG PLUS" + Windows environment Operating system; 20 GB hard drive; 17" TFT monitor; international keyboard, soft touch keypad & industrial mouse; RS-232 Serial ports, USB ports; (1) 1.44 MB floppy drive; (1) CD ROM drive; all mounted in separate control console. -- Operating System:"XYLOG PLUS" Offers Real time multitask processing; programs can be transferred via diskette or downloaded by wire. -- Complete with: Pneumatic part clamping devices; sound enclosure; safety mats. -- Operating features: Machine can work the panel from above & below at the same time and can produce (2) identical or mirrored panels per cycle with no difficulty.The "UNIFLEX" can machine porous materials since the pieces are held with grippers, directly managed by the numerical control; it can even process small pieces and carry out "through" machining.(4) Operating modes at each cycle, it can change automatically from: Top machining to bottom machining, to top & bottom machining together, either on (1 or 2) stacked panels. -- Actual model is MORBIDELLI UNIFLEX HP.