SNX nVISION SYSTEM G1 SEMI-AUTOMATIC CONTOUR EDGEBANDER: -- Specifications: Curved (Contour) Edgebander to allow 360° edgebanding to contoured (shaped) panels.Edgebanding is applied automatically as part is advanced past the edgebanding workstations via turntable.Reduced learning curve/expertise for operation as operator simply loads part to vacuum turntable, then activates the edgebanding cycle. -- Working Capacity: The nVision 1 can band Minimum material size 150 mm (6") diameter.Maximum material size 2,400 x 2,400 mm (94" x 94"); Maximum material weight up to 104.5 KG (230 lbs).Material thickness from 10 - 60 mm (0.4" - 2.36"); Banding thickness from 0.5 mm thin tape w/low temp adhesive - 3mm tape. -- Radii Capacity:Minimum Internal (inside) radius 80 mm (3.14"); minimum external (outside) radius 30 mm (1.18") based on 1 mm thick edge tape. &#9679 Edgebanding thickness 1 mm, min = R 30 mm &#9679 Edge thickness 2 mm, min = R 50 mm &#9679 Edge thickness 3 mm, min = R 80 mm &#9679 Panel thickness 10-60 mm with edge thickness 1 mm &#9679 Panel thickness 10-60 mm with edge thickness 2 mm &#9679 Panel thickness 10-45 mm with edge thickness 3 mmIMPORTANT: ALL minimum & maximum radii are affected by tape thickness, quality of adhesive and edgebanding being applied. Radius size dramatically affected by adhesive temperature and quality of edge tape; semi or rigid.Equipped with:Thermal-regulated glue pot heated via (2) 800 Watt heating elements with electronic temperature controls; holds up to 1 kG (2.2 Lbs) of granules. (2) Pressure rollers to copy the shape of the piece, automatic guillotine for coiled material up to 3 mm (0.11") thickness & 57 mm height (0.125" - 2.25"). Features: -- Laser for easy length identification with closed parts without the need for additional length measurement.The Laser also detects a tight radius and will automatically slow the speed + resume the set speed when the detected radius has passed.The machine is also equipped with the foot pedal for manual control/intervention. Motorized turntable for automated edgebanding application to large panels.Holding or support arm has a large inter-changeable vacuum pod to secure panels for edging and trimming.NOTE: Panels can be irregular in shape but must conform to the min. tolerances of inner & outer radii and fit within the work area.Complete with: &#9679 Top & Bottom Trimming unit &#9679 Centralized control panel with individual controls for all stations to enable manual feeding of panels if desired &#9679 Banding station &#9679 Edgeband coil stand &#9679 Standard-size vacuum pod for articulated arm &#9679 80 mm dia. (3") dust extraction outlet &#9679 Foot pedal activation/de-activation control &#9679 Larger feed roller &#9679 QC Glue tank with sensor. -- Actual Model is SNX nVISION SYSTEM G1

SNX NVISION SYSTEM2 CONTOUR EDGEBANDER: -- Specifications: Curved (Contour) Edgebander to allow 360° edgebanding to contoured (shaped) panels.Edgebanding is applied automatically as part is advanced past the edgebanding workstations via turntable.Reduced learning curve/expertise for operation as Operator simply loads part to vacuum turntable, then activates the edgebanding cycle. -- Working Capacity: The "nVision" Contour Bander can band a minimum material size of 150 mm (6") diameter.Max. material size of 2,400 x 2,400 mm (94" x 94"); max. material weight up to 104.5 kG (230 Lbs).Material thickness from 10 - 60 mm (0.4" - 2.36"); banding thickness from 0.5 mm thin tape w/low temp adhesive - 3 mm tape. -- Radii Capacity:Minimum internal (inside) radius of 80 mm (3.14"); minimum external (outside) radius of 30 mm (1'18") based on 1 mm thick edge tape. &#9679 Edgebanding thickness 1 mm, min = R 30 mm &#9679 Edge thickness 2 mm, min = R 50 mm &#9679 Edge thickness 3 mm, min = R 80 mm &#9679 Panel thickness 10-60 mm with edge thickness 1 mm &#9679 Panel thickness 10-60 mm with edge thickness 2 mm &#9679 Panel thickness 10-45 mm with edge thickness 3 mmIMPORTANT: ALL minimum & maximum radii are affected by tape thickness, quality of adhesive and edgebanding being applied. Radius size dramatically affected by adhesive temperature and quality of edge tape, semi or rigid. -- Equipped with:(1) NEW Thermal-regulated glue pot heated via (2) 800-Watt heating elements with electronic temperature controls; holds up to 1 KG (2.2 LBS) of granules. (2) Pressure rollers to copy the shape of the piece, automatic guillotine for coiled material up to 3 mm (0.11") thickness & 57 mm height (0.125" - 2.25"). -- Features: TRIAX 3-AXIS Laser System (patented) for tighter butt joints & easy length identification with closed parts without the need for additional length measurement.The Laser also detects a tight radius and will automatically slow the speed + resume the set speed when the detected radius has passed.The machine is also equipped with the foot pedal for manual control/intervention. Motorized turntable for automated edgebanding application to large panels.(2) "Heavy Duty" Articulating arms to support the parts during edgebanding and trimming & to maximize production throughput. Arm has a large inter-changeable vacuum pod to secure panels during edging and trimming. NOTE: Panels can be irregular in shape but must conform to the min. tolerances of inner & outer radii and fit within the work area. -- Complete with: &#9679 Top & Bottom Trimming unit &#9679 Centralized control panel with Simple PLC Touchscreen Interface with individual controls for all stations to enable manual feeding of panels if desired &#9679 Banding station &#9679 Edgeband coil stand &#9679 Standard-size vacuum pod for articulated arm &#9679 80 mm dia. (3") dust extraction outlet &#9679 Foot pedal activation/de-activation control &#9679 Larger feed roller &#9679 QC Glue tank with sensor.

Combination Differential/Filling Machine SMARTCOATER with: 880 mm (34-1/2") Working/pass-through height; one of the best units ever produced. Dual purpose machine can be utilized as: -- 1) A standard differential Roll Coater for application of UV sealer or top coat material; as a differential Roll Coater the 1st application head is independently utilized to for precisely controlled application. -- 2) A Filling Machine for application of H2O or UV filling material to calibrate substrates with porous veneer; as a Filling Machine, both heads are utilized for application and reverse smoothing or pressing of UV filling material.Specifications: -- (2) Heads, 53" width cap. - 1st Head: 250 mm (9-3/4") Dia. rubber coated applicator roller with separate doctor roller; doctor blades are oscillating. -- 2nd Head: 245 mm (9-5/8") Dia. chromium coated smoothing/reverse roller w/separate chromium doctor roll; all heads are floating to compensate for calibration errors & minimize damages from oversize parts. -- Adjustable opening 0 - 100 mm (3-3/4"); thickness protection safety bar connected to pneumatic emergency lifting; EX-proof electrics on all motors. -- 2 HP Conveyor drive: Variable feed speed from 26 - 131 FPM; 1/2 HP variable RPM drive on doctor rolls and separate 3/4 HP drive on applicator & reverse rollers. -- Electrical power: 480 V, 3-Ph, 3.8 kW; 7 Amps.

SORBINI TM/95-2F Flow Coater Specifications: -- 24" Coating width, 4" max. thickness, hand crank controls curtain thickness, (1) head gravity feed. -- 2 HP feed motor for variable feed speed from 90 - 350 FPM, (1) 1.5 HP circulating pumps, (1) stainless steel tank & return reservoir. -- Conveyor: 24" Wide, 60" Long at infeed, 72" long at outfeed. 34" long center belt.

SORBINI SMART COATER MF Single Head Differential Roll Coater;SORBINI - Single-Head Roll Coater, ... "SMARTCOATER MF" SeriesMachine Features & Benefits:Single-Head Roll Coater designed for smooth application.Conveyor belt made of: Solvent resistant material with automatic tracking rollers mounted underneath the application rollers (182 mm dia.).Application rollers (250 mm dia.) covered with Heavy Duty vulcanized rubber of different shore hardness for different applications & coating products.Heavy gauge chromed steel doctor rollers (173 mm dia.).Feeding belt, coating rollers, and doctor rollers are all driven by independent motors and inverter is controlled directly from the control panel.Self-leveling floating head for optimum application on uneven surfaces.Thickness control and indicator on the control panel.Different types of scrapers are available according to the coating product and type of application.Pneumatic pump for lacquer feeding and recirculation.Differential capability allows for rotation inversion of doctor rollers and for fine adjustment of the applied coating, particularly important for high quality top coats.Safety "Cleaning Mode" to facilitate and safely service the machine.Technical Specifications:Working width from 0 to 1,300 mm (0 to 51 in).Min. workpiece length: 305 mm (12 in).Speed range: 2 - 11 MPM (6-1/2 to 36 FPM).Power consumption: 4 kW.Compressed air required: 15 Nl/Min (0.53 CFM) exhausted solvent/air mix. Working side: Right.Electric equipment: Explosion proof.Footprint Dimensions: Length 898 mm (35 in.) width 3,282 mm (129 in.) height 1,674 mm (66 in.).

CEFLA/SORBINI, VS 34/ACT/1600 - Top Only Panel cleaning machineEquipped with:One (2) Anti-Static ionization bar. One (2) soft horse hair brush, in opposite rotation to panels feed direction, 400 RPM brush speed.One (2) timed, compressed air blower Min. work piece length 290 mm (11.5";).Belt conveyor with variable speed feed from 3 - 16 MPM (approx 10 - 52 FPM). Hand wheel for thickness adjustment.

2022 CNC controller! Under power & ready to demo! 3-Axis CNC Vertical Milling Machine - Seller has outgrown and upgraded to larger capacity CNC Machining Center. - Table size 10" x 50" x 38” H - Travels: X-Axis: 31", Y-Axis: 17", Z-Axis: 23-1/2" - Quill travel 5" - Quill diameter 100 mm (3.94") - No. 40 Spindle taper - Variable spindle speeds 80 - 4,000 RPM - Rapid traverse 150 IPM - Distance from spindle nose to table (Maximum part height) 23-1/2" - Distance from spindle center to column face 19" - Maximum weight of workpiece 1,320 Lbs. - Maximum work capacities: 1" Drilling & Tapping mild steel & Milling (Metal removal rate/mild steel) 5 cu. in./min. - 5 HP Spindle motor - 560 in-oz Continuous torque D.C. servo motors & Precision ground ball screws for X, Y, & Z-Axes - YEONG DIEN Automatic lubrication unit Includes: - 2022 "PROTOTRAK SMX3" 3-Axis CNC Control/3-Axis Digital Readout (Control defines tool path based upon user defined part geometry), with Pentium PC-processor with 512 MB RAM, 10.4? Color active-matrix screen, Touchpad, (4) USB connectors, MICROSOFT "WINDOWS" Operating system, Program feedrate override & Tool path graphics - ALL MACHINE PARTS "MAXI TORQUE-RITE" Pneumatic drawbar, with 40 - 50 ft. Lbs. of torque - EKSTROM CARLSON "MISTIC MIST 1ST-2LC" 1 Gallon Capacity Coolant Mist Generator, with Adjustable air & Liquid control valve - WALDMANN "ROCIA.FOCUS" 600 Lumen 5,000 K Sealed Housing LED Work Light

SPEC AIR Model R-44SQ Dust Collector with Shaker Bag Cleaning, Abort Gate, Spark Detection, Rotary Air Locks and Relay Fan in a closed loop configuration. -- Overall Data: 46,000 CFM with approx. 6170 sq. ft. of cloth area consisting of (286) filter bags operating at 7.4:1 Air-to-Cloth Ratio (ACR). 'Can velocity' (upward) is 211 FPM. Polyester filter bags are 9" dia. x 110" long. -- Fan:/Motor: SPEC-AIR EB-44 Clean Air Fan with approx 44" dia. inlet/outlet, ground- mounted in an upblast arrangement. Fan can deliver 46,000 CFM @ 16" SP. Inspection door, and belt guard. Belt-driven by a TOSHIBA 200 HP High Efficiency (Inverter Duty), TEFC motor, 447T frame at 1780 RPM. -- Bag Cleaning: Via (2) Shaker motors with a lattice of tie-rods inter-connected to each row of bags. Bags are accessed from the top clean air plenum.Timer relay from low voltage controls for bag cleaning. -- Comes with: (2) Tapered hoppers separating the large particles, large access door, Backdraft Dampers adapted to (2) 32" filter inlets, lower hopper bottom each with Rotary Air Lock. Discharge from both RAL's is connected to a Material Handling Transfer/Relay fan into an enclosed container (not included) for continuous collection of waste. A return pipe from container makes this a closed loop configuration. Explosion doors. Safety ladder to top return air plenum.. Magnehelic differential pressure gage to monitor the condition of the filter bags. -- Construction: Heavy gage construction with reinforcing ribs and Flange-bolted in the middle easily allows units to transport into two units, ie 120" x 141".Return Air starts from filter outlet with adaptor to 44" dia. fan inlet. Discharge Silencer of fan outlet has a 44" Abort Gate returns air into building. -- Features: HANSENTEK Spark Detection system. Main electrical panel with pushbottons and controls. -- Includes: Filter housing and outside pipe is fully covered with insulation to minimize heat loss & reduce plant heating cost. -- Overall dimensions: 282"; Long x 120"; Wide x 317"; High. Weight approx. 20,000. Lbs. -- Note: Unit was moved in 2020 to current location, refurbished added installation.

SPEC AIR Model R120-26RD-OC Baghouse Filter Auto Shaker Type Dust Collector Loaded with features. -- Capacity of approx.15,500 CFM and the following features and components: -- EB-26, 60 HP SPEC AIR, Air Handling Fan , 15.500 CFM @ 16" SP mounted in a negative pressure configuration (clean air side) with return air and with automatic 26" dia. Abort Gate Damper according to NFPA-68-69 CODE. 110 volt actuated by the Spark Detection System. -- HANSENTEK AN104 Spark Detection/Suppressions system Per NFPA 64-68 and c/w BPS-9X4 Booster Pump & FLEXCON P2P20 Tank. -- 1,961 sq. ft. of filter area using (97) high efficiency Polyester bags. Operating at 7.9 to 1 ACR (Air to cloth ratio). -- 26"; Diameter Inlet & outlet duct. -- Tangential inlet with Backflow Damper, according to NFPA-68 CODE. -- Top mounted motorized bag shaker. mechanism powered by 1.5 HP. -- Rotary Air Lock with 96" clearance. (4) leg support steel frame & Safety access ladder. -- Explosion Venting Doors, according to NFPA-68 CODE. -- Filter Bag size approx. 9" dia. x 9' long, -- Inline 26" dia. Silencer muffler on return air duct. -- Ground mounted Belt Driven Fan complete with TEFC motor and inspection door. -- Features: 60 HP Soft Start Controller. -- ENGINEERED ELECTRIC Control Panel with starters and controls. -- Manometer gauge to monitor differential pressure (life) of filter media. -- Housing/Support Steel dimensions: 120" long x 120" wide x 32' high. Approx. 13, 500 Lbs. -- Some pictured pipe is included.

SPEEDAIRE - 4B228D, ...Portable CompressorSpecifications: -- 6 HP Reciprocating Air Compressor; Pump # 4B247A; 10.3 SCFM @ 90 PSI; 9.1 SCFM @ 135 PSI. -- Max. pressure rating: 135 PSI; 26-Gallon horizontal air receiver on (2) wheels; motor and flywheel guard.6 HP Motor, wired for single-phase, 240 Volts, 15 Amp. -- Complete with: -- Single-stage Compressor head; air pressure regulator gauge, and tank pressure gauge; start-stop auto or manual cycle controls; pressure relief valve. -- (1) Air discharge port with quick disconnect.

SPROUT Rotary Drum Dryer with Gas Burner;Complete with the following components: -- 7.5 Ft. x 24 Ft. Steel Rotary Dryer Drum. -- Natural Gas Burner (may be converted to LP) with 13.5 Ft. Refractory Lined Furnace Tube. -- Belt Drive with Gear Reducer and Electric Motor. -- Trunnion Bases complete with Forged Trunnion Wheels. -- Forged Trunnion Tracks (weld-on style) ...look like new. -- Vertical drop material Inlet Transition with Side Access Door. -- Rated for approx. 2 TPH water evaporation or about 4.5 TPH wood sawdust input. -- OPTIONAL ITEMS: &#9679 Receiving Bin with Airlock and Screw discharge Conveyor. &#9679 Material Input Screw Conveyor. &#9679 Main Fan.

SQUARE D - 75T3H, ...75 KVA, 480 - 208 V, 3-Phase Autotransformer Specifications: -- Intended for power, heating, and lighting applications. -- Enclosure Rating: NEMA 2. -- Multi-Tap (432 - 504 V) Primary 480 V (Delta); Secondary 208Y / 120 V @ 60 Hz ventilated. -- Aluminum windings. -- cULus Listed. (2) Available; price per unit. - Make offer for both!

SSI Model - 1000-E, Slow Speed, High Torque ShredderSpecifications: -- 50 HP Motor; twin shafts; 40" x 25" ChamberIncludes: -- Stand, feed hopper; controls

STAHL - PTB 01 ATEX 1016, ...Single Sheet Panel Turner.Specifications: -- 40" X 144" Capacity. -- Hydraulic pump for the rotation. -- The turning cycle is to match Finishing Line Speed running between 5.5 to 6 MPM.NOTE: Came out of a Finish Line.

STANMAC SPRAY 300 Moulding Sprayer The Stanmac "Spray 300" is ideal for linear profiles in a wide range of materials and capable of utilizing both waterborne and solvent-based coatings including stains, paints, and lacquers.Spray guns are automatically timed for the start and stop of the spray cycle to ensure the best spray efficiency. The overspray is captured by the spray trough and can be recovered while atomized spray is captured by fiberglass media and clean air is exhausted from the spray cabin.Can be fitted with spray gun packages to include conventional, air-assisted airless, and airless to suit your requirements.Specifications: -- Workpiece max. width: 12"; -- Workpiece min. length: 30" -- Feed Speeds: 30 - 150 FPM -- Feed Motor: 0.5 HP -- Extraction Fan: 3.0 HP -- Number of Spray Guns: 3 -- Recovery Troughs 1 -- Spray Gun Trigger: Electronic Switch -- Piece Counter: Digital -- Filter Media: Replaceable fiberglass media

STANMAC "MC/WB 300" Vacuum Coater; 3- or 4-sided coating. -- 8" Max. width x 2-1/4" max. height cap.; 24" min. length. -- Substrate enters vacuum chamber via 6" conveyor belt and passes through the coating; variable speed from 30 - 200 FPM as the substrate leaves the chamber. -- Negative pressure in the chamber keeps excess fluid inside resulting in 100% transfer efficiency; coating runs through several filters and is sent back to the reservoir for use again. -- Equipped with: (1) 15 HP Regenerative vacuum producer that holds fluid inside vacuum chamber; 15-gallon capacity reservoir; stainless steel vacuum chamber with adjustable substrate holddowns & guides. -- Equipped with: Air operated diaphragm Recycling Pump, high capacity fluid filter, separation tower with stainless baffle, and filtering system. -- Heavy gauge steel construction and free-standing control/operator panel. -- 100% Transfer efficiency; coating thickness controlled with a modulating valve & vacuum pressure gauge. -- Uses waterborne coatings for stains, primers, sealers, basecoats, topcoats, and even fungicides; can be used to coat most solid materials regardless of shape or length.

STAR V MACHINERY SCG-1600 AUTOMATIC CROSS GROOVER + TIGERSTOP TS08 STOP/PUSHER: -- Specifications:(1) Spindle with 7.5 HP - 3,600 RPM motor, 60" max. crosscut cap., material thickness 0.25" - 1.125"; head up & down movement via pneumatic cylinder with linear rail & linear bearings, depth fine adjustment with special threaded adjustable unit. -- Carriage cross-travel powered by a 3 HP hydraulic motor (4GPM), driven ball screw with linear rail & linear bearings; feed rate from 0 - 40 FPM; Heavy Duty welded frame construction. -- Complete with:Safety guards and cutter guards; pneumatic support fence; heavy-duty in-feed & out-feed roller tables. -- Options Include: TigerStop TS08, 8' (96") long, NC controlled stop/pusher system, mounted to the LH side of the machine. (4) manual flip-stops with Pro-Scale digital readouts, for 60″ of scaled capacity, mounted to the RH side of the machine. Reciprocating taping machine is built directly in front of the bed of the cutting area eliminating the need for taping by hand -- Actual Model is STAR V MACHINERY SCG-1600 AUTOMATIC CROSS GROOVER + TIGERSTOP TS08 STOP/PUSHER.

STAR V MACHINERY SLG-2000 36 LINEAR V-GROOVER: -- Specifications:Working table dimensions are 120" long x 36" wide; Working width from 4" - 36"; Working length from 20" - infinite; Working thickness from 0.25" - 1.2".Maximum throat clearance for linear & cross-cuts is 15". -- Equipped with: (2) Independent, 12 HP-3,600 RPM Saw Motors with "servo" control adjustment in "Y" axis & manual "Z" axis adjustment.30 mm Dia. Arbor x 4" clamping length to accommodate wider cove back splash, triple-fold profiles, or using it for hogging and finish cut; 9.5" max. cutter-head dia.1-Saw motor is mounted on the front & 1-Saw motor is mounted on the back of the 8" x 12" x 1/2" heat-treated steel heavy-duty overhead support beam.Side to side head travel via linear rails & bearings, manual head height adjustment via linear rails & bearings. -- Feeding System:(1) 3 HP Variable speed drive belt system with "servo" height adjustment; Feed rate from 0 - 60 FPM, belt feeder moves workpiece on a precision "stainless-steel" roller table; -- Tape Applicator: (2) Automatic Tape Applicators with "servo" adjustment, according to the Saw motor position in "Y" axis. -- Operator Interface:10" HDMl Touch Screen Display for Start/Stop, On/Off, Feed Speed & Axis Position. -- Complete with:; Safety guards and Cutter guards. Anti-Kick-back Device. Emergency Shutoff line. Dust collection requirements 4,200 CFM, collector outlets on cutter guards 5" in dia.. -- Options Include: Increased Working Width Capacity from standard 36" to 40" (1,016 mm) Modify Feeder System to allow 2" Thick Material to pass. Increased Cutter Guarding & Motor Shafts to accept tooling & process 2" Thick Material (1) 10'x30" (3mx76cm) lnfeed Conveyor (1) 10'x30" (3mx76cm) Omni Directional Ball Transfer Table (2) Brazed Carbide 90 Degree V Groove Cutter for up to 1" Thick Material (2) Rolls of 2" (50mm) wide V-Groove Tape. -- Actual model# is STAR V MACHINERY SLG-2000 40-2".

STATE - B-4, ...Oscillating Spindle SanderSpecificationsTilting table design with pedestal floor mount.Table size: 20" x 24".Table height: 40".Table tilt: 15° Up; 45° down.Spindle speed: 1,725 RPM.Vertical oscillation: 1-5/8".Oscillations/Min: 90.Lubrication: Oil bath splash. -- Heavy-Duty 1/2 HP motor; maintenance free; 1,725 RPM; TENV totally enclosed non-vented motor; rated for continuous operation; assuring long term dependable service. -- Safe operator controls; magnetic motor starter with overload protection for save installation.All controls mounted for operator convenience. -- Operator friendly handwheel tilting Engineered worm gear design allows table to be tilted 15° up & 45° down relative to spindle.Easy-to-read scale allows for accurate tilt determination before engaging locking device. A tapered pin locks the table during horizontal sanding operations. -- Safety features: Magnetic motor starter with overload protection; safety labels; well-placed ergonomic controls; 3-throat rings to minimize table-to-spindle clearance; POSITIV-LOK spindles provide safe & quick means of changing spindles. -- Recently cleaned, checked; electrical contacts cleaned; machine partially disassembled cleaned; reassembled & tightened; oil sight glass replaced.Weight: 280 Lbs.

STATE B-4 OSCILLATING SPINDLE SANDER 1.5 HP Motor with manual switch, (9) spindles from 1/4" DIA to 4" DIA., 1,725 RPM spindle rotation, 20" x 24" table tilts 15° up and 45° down, table height 40". Also includes work light