Custom-Built DEIMCO Through Feed Sprayer with a BLASDEL IR Preheat Tunnel that is available MARCH of 2023. Until then, the System can be seen in operation. -- Line was designed to preheat Fiber Cement board prior to painting and is followed by a Single-Arm Reciprocating Sprayer with 4-Spray Gun cap. Spray Guns not included.SEE ATTACHED VIDEO FOR A GOOD LOOK AT THE LINE's OPERATION!Built in 2019, the System was used for approx. (2) years; current owner changed their process and no longer requires the equipment.Oven width cap.: 60" Wide, 1-3/4" part height cap.; overall Oven dimension: 84" Wide x 12-1/2' long x 55" high, excluding the Blower & Stack. Line/Conveyor: Variable speed drive, 18.5 FPM to 26 FPM; Reciprocator operates up to 260 FPM and set by the HMI. 2-Zone Oven: -- Zone 1: (2) Upper left side wall/ceiling mounted; 18" x 60" emitters. -- Zone 2: (2) Right upper side wall/ceiling mounted 18" x 60" emitters; 8" clearance between emitters & rolls. Heaters: Natural gas using 7" WC; 480 Volt preheat; TC, FM, flange frame. - Gas Ratings: 360,000 BTUH Max. input ; 100,000 BTUH standby input; Air Exhaust on infeed & Injection Blower on outfeed. Electrical ratings: 26.6 Amps, 480 V - 3 Phase, 60 Hz.Exhaust: 980 CFM, 1 HP Motor.Control Panel: 60 AMP Disconnect switch, ALLEN-BRADLEY "Panel View Plus HM", IEC contactor & High Temp PID exhaust.NOTE: (25) New replacement conveyor rollers & (40) reconditioned rollers for IR Tunnel.DIEMCO Sprayer complete with: (1) Reciprocating Arm holds (4) guns and reads the leading & trailing edge to turn on & off the guns as the parts feed through; best to run full width loads through Sprayer; Overspray funnels into buckets.Spray Guns turn on & off based on the part leading & trailing edge; read by a light curtain on the infeed end.Dims: GFS Spray Cabin: 13' Deep x 8-1/2' wide x 9' high surround the reciprocating arm. - Filter & Exhaust Section: 13' Wide x 3' Deep x 10' High.

MCRS is a Bagging System for mulch, compost, rock, or sand. This system is complete with a 2-yard product surge hopper, a 20' X 24" wide troughed incline product delivery conveyor with a cleated belt, an 8' bag closing conveyor, and a custom 7.5 HP Elec/hydraulic power unit. The system can fill bags by time and depth of stream or digitally with load cells.Standard construction carbon steel Powder Coated Industrial Gray(RAL 7046).The MCRS operation has been designed for one man to bag fill, bag close, and stack three bags per minute continually. -- The operator hangs bag #1 on the scale, hits the palm switch to close the CG spout, and automatically fills it. -- Bag #1 will drop once the timer times out onto the moving conveyor and hangs bag #2 into position, hits the palm switch, and starts the filling. -- The operator steps to his left. Bag #1 contact a wand switch and is in position underneath the impulse sealer. --The operator starts the bag into the impulse sealer. Once completed, bag #1 is then manually stacked. -- Bag #2 filled and waiting for the operator's return. -- Bag #2 is then released, and bag #3 hung. -- The process is then repeated.The Front End loader feeds the system. Consists of the following --infeed hopper --incline conveyor --dosing system --bag closing system:Bag Closing System Consists of a (CON 508) 8' long x 1' wide smooth top belt to take bags into aposition where a wand switch manually stops them. The bags are then prepared and enteredinto theImpulse Sealer (31103737610) Programmable Impulse Sealer for the repeated sealing of thermoplastic films such as polyethylene and polypropylene. This automatic single-impulse heat sealer is controlled by a plug-in transistorized circuit board and electronic timers. The timed closure ensures an even and consistent seal. --THE PRICE REFLECTS AN UPGRADE FROM THE IMPULSE SEALER TO A SEWING SYSTEM.The operator has hands free to handle the product quickly. This type of machine generally increases workers' productivity.The electric foot pedal is included for manual operation. -- Seal Length: 24" -- Seal Thickness: 8 mil -- Seal Width: 10 MM

EXPRESS SCALE CM-780D-II Bagging System with ConveyorsSpecifications: -- Air-operated double door weigh hopper: 3.5 CuFt -- Load cells: 100 KG (220 Lbs) -- Weigh Range: 10-110 Lbs or 5-100 kG -- Cycle Speed (simplex): 13 bpm (50 lbs or 25 kG) -- Cycle Speed (duplex): 22 bpm (50 lbs or 25 kG) -- Typical Accuracy: ±2-3 oz. or ±56-85 gramFeatures: -- 1280 Express Digital Programmable Controller with digital readout -- RS232 output -- Operator station. -- Protect individual or all parameters via pass-code protection -- Ethernet connectionSystem Equipped with: -- Gravity Feeder: High-Output Gravity Gate (13" x 8") 2-position for bulk and dribble feed. Handlingfree-flowing products such as grain, seed, and prilled fertilizers. Rated at 14-16 bags per minuteSimplex or 22-24 BPM - duplex. Typical accuracies will be +/- 2-3 ounces (56-85 grams). -- Spout Assembly: Dust Tight 21", 25", or 31" Circumference -- Hopper Surge: For simplex scale only, mild steel construction gray powder coated 40 CU' capacity(operator platform and handrail not included) 4"x 4" x 1/4" wall tube, 3/16" Metal Plate for wallsof Hopper. -- Conveyor: 22' x 18" product delivery: 2 HP Motor, 3" Scoop Cleat Belting w/ Hopper for Unloading Bulk Bags -- Bag Closing Conveyor with Air-Flo Hot Air Heat Sealer: 10' overall length, 1/2 HP motor, 12"-wide 3-ply neoprene smooth top belt, 110V variable speed motor mounted internally, adjustable conveyor height 13.5" to 18.5" and adjustable back plate, electrical controls include on/off switch.Backed by a 1 year warranty and lifetime customer support.

EXTREMA RC-04 Rotary Air Lock Standard capacity Rotary Air Lock; Cycles waste off of a cyclone dust collector while maintaining internal pressure.Specifications: -- The Rotary Air Lock is an essential device for dust collectors that dump directly into a dumpster or hopper. -- This unit has a 16" dia. lock with a 1/2 HP motor. -- 33 RPM TEFC Direct drive motor. -- 16" Inlet dia. & 16" outlet diameter. -- (8) Rubber blades. -- Does not include electrical controls. -- Features: Approx. 10 Cu. Ft./Min capacity.

EXTREMA DB-100 TYPHOON BLOWER. Capacity 10 HP, 6,350 CFM. -- Solid heavy gauge steel construction. -- Heavy duty dynamically balanced steel impeller, 12" inlet, 14" impeller, 14" outlet. -- Rotatable collection port for use in a variety of applications. -- Safety guards on all inlets. - Complete with magnetic starter. -- Note: 460 Volt available.

EXTREMA DB-150 TYPHOON BLOWER. Capacity 15 HP, 7,900 CFM. -- Solid heavy gauge steel construction. -- Heavy duty dynamically balanced steel impeller, 14" inlet, 25" impeller, 16" outlet. -- Rotatable collection port for use in a variety of applications. -- Safety guards on all inlets. - Complete with magnetic starter. -- Note: 460 volt available.

EXTREMA RC-10 Air Lock Standard capacity Rotary Air Lock; Cycles waste off of a cyclone dust collector, while maintaining internal pressure. -- The Rotary Air Lock is an essential device for dust collectors that dump directly into a dumpster or hopper. -- This unit has a 16" dia. 1 HP - 33 RPM TEFC Direct drive motor -- 16" inlet dia. & 16" outlet dia. -- (8) rubber blades. -- Does not include electrical controls. -- Features: 38 Cu. ft./min. cap.

EXTREMA DB-250 TYPHOON BLOWER. Capacity 25 HP, 10,350 CFM.Specifications: -- Inlet 18", 27" impeller, 20" outlet. -- Solid heavy gauge steel construction. -- Heavy duty dynamically balanced steel impeller. -- Rotatable collection port for use in a variety of applications. -- Safety guards on all inlets. -- Complete with magnetic starter. Note: 460 Volt available

EXTREMA DCY-1220 L3 TYPHOON Cyclone Filtration Dust Collection System. -- Powerful two-stage dust collection drops out heavier dust particles through a Rotary Air Lock, allowing you to choose the disposal system, before passing finer particles through the fan and filter. -- Air volume rated @ 8,800 CFM. -- Unit includes; 20 HP Motor, with a Soft Start already wired in. -- Rotary air lock with a 1 HP motor @ 38 CFM. -- Low noise operation. -- Standard support frame LEG 3 164" clear height x 149" clear width x 91" clear depth. -- Return air filters also available.

EXTREMA DCY-1215 L3 TYPHOON Cyclone Filtration Dust Collection System.Powerful two-stage dust collection drops out heavier dust particles through a Rotary Air Lock, allowing you to choose the disposal system, before passing finer particles through the fan and filter. -- Air volume rated @ 7,600 CFM. -- Unit includes: 15 HP Motor, with a Soft Start already wired in. -- Rotary air lock with a 1 HP motor @ 38 CFM. -- 14" Inlet Low noise operation. -- Standard support frame LEG 3 164" clear height x 149" clear width x 91" clear depth. -- Return air filters also available.

EXTREMA DCY-1425 L3 TYPHOON Cyclone Filtration Dust Collection System. Powerful two-stage dust collection drops out heavier dust particles through a Rotary Air Lock, allowing you to choose the disposal system, before passing finer particles through the fan and filter. -- Free air volume rated @ 10,500 CFM. -- Low noise operation. Equipped with: -- 25 HP Motor, with a Soft Start already wired in. -- Rotary air lock with a 1 HP motor @ 38 CFM. -- Standard support frame LEG 3 164" clear height x 149" clear width x 91" clear depth. Other Options available: Return Air Filters (DCF-5) plus the pipe to connect the Cyclone with the filter and 460V electric rather than 230 Volt.

EXTREMA DC-3250S TYPHOON Fabric Filtration Dust Collection System. With 1-micron dust filtration efficiency this collector will make your shop cleaner, healthier, and more productive.Specifications: -- (6) Fabric filter top bags are mounted above individual plastic collection bags. -- The multi-bag system is placed on sturdy steel legs in a horizontal series. -- 10,000 CFM Output with single-stage blower. -- Additional filtration sections can be easily added. -- Heavy Duty 25 HP induction motor, 18" inlet -- 27" Steel blower fan impellers are dynamically balanced. -- Collection bag snap-in rings for easy addition or removal of plastic bags. -- 1-Micron filter bags with 6 mil plastic bottom collection bags are standard. -- Wye-Delta soft start power switch. Options: Remote control, changing 230 to 460 voltage

EXTREMA DC-232.3 TYPHOON Fabric Filtration Dust Collection System. -- Powerful, portable, and affordable dust collector with roll around casters mounted to a steel platform base. -- (2) Oversized Fabric filter top bags are placed above fabric collection bags. -- 2,950 CFM Output with single-stage blower. -- 3 HP Induction motor. -- Filter bags filter dust particles down to (2) Micron in size. -- Quad 4" dust port adapter.

EXTREMA DB-75 TYPHOON BLOWER. Capacity 7.5 HP motor and rated at 4,700 CFM. -- Solid heavy gauge steel construction. -- Heavy duty 13.5" dia. dynamically balanced steel impeller. -- 12" Inlet, 13.5" impeller, 14" outlet. -- Rotatable collection port for use in a variety of applications. -- Safety guards on all inlets. -- Complete with magnetic starter. -- Note: 460 Volt available

EXTREMA DCF-327E Baghouse Dust Collector.Features a 16" inlet; unit has (3) sections with (9) socks per section. -- Filter Socks: 6" Dia. x 70-7/8" for greater air-to-filter ratio; (1) Micron filter. -- Available for outdoor & indoor use; unit is enclosed. -- Excellent addition to the "DCY Typhoon" Dust Collector; ...ask us why!

EXTREMA DC-250.3 TYPHOON Cyclone & Fabric Filtration Dust Collection System. Powerful two-stage dust collection drops out heavier dust particles into a drum before passing finer particles through the fan and filter.Specifications: -- (1) Fabric filter bag placed above plastic collection bag. -- 2,975 CFM rated output. -- 5 HP Induction motor. -- 14-1/4" Steel blower fan impeller is dynamically balanced. -- Collection bag snap-in ring for easy addition or removal of plastic bag. -- Filter bag filters dust particles down to (1) Micron in size. -- Low noise operation. Includes: Sturdy steel tripod cyclone mounting stand. Drum dollie (drum not included).

EXTREMA DC-275.3 TYPHOON Cyclone & Fabric Filtration Dust Collection System. -- Powerful two-stage dust collection drops out heavier dust particles into a drum before passing finer particles through the fan and filter. -- (2) Fabric filter bags placed above plastic collection bags. -- Air volume output rated @ 4,850 CFM. -- 7.5 HP Induction motor. -- 14-3/4" Steel blower fan impeller and is dynamically balanced. -- Collection bag snap-in ring for easy addition or removal of plastic bag. -- Filter bags filter dust particles down to (1) Micron in size. -- Low noise operation. -- Includes: Sturdy steel tripod cyclone mounting stand and drum dolly. (drum not included).

EXTREMA DC-2100 TYPHOON Cyclone & Fabric Filtration Dust Collection System.Powerful two-stage dust collection drops out heavier dust particles into a drum before passing finer particles through the fan and filter.Specifications: -- (2) Fabric filter bags placed above plastic collection bags with 117 Sq. Ft. total cloth area -- 32 Cu. Ft. of storage capacity -- Rated at 6,400 CFM at 16" static pressure output. -- 10 HP Induction Motor. -- Inlet 13" with 16" Steel blower fan impeller that is dynamically balanced.Features: -- Collection bag snap-in ring for easy addition or removal of plastic bag. -- Filter bags filter out dust particles down to (1) Micron in size. -- Low noise operation. Includes: -- Sturdy steel tripod cyclone mounting stand and drum dollie (drums not included).

EXTREMA DC-3050.3 TYPHOON Fabric Filtration Modular Dust Collection System. -- With 1-micron dust filtration efficency this collector will make your shop cleaner, healthier, and more productive. -- (2) Fabric filter top bags are mounted above individual plastic collection bags. -- The multi-bag system is placed on sturdy steel legs in a horizontal series. -- 3,075 CFM Output with single-stage blower. -- Additional filtration sections can be easily added. -- Heavy Duty 5 HP blower motor. -- 13" Steel blower fan impellers are dynamically balanced. -- Collection bag snap-in rings for easy addition or removal of plastic bags. -- 1-Micron filter bags with 6 mil plastic bottom collection bags are standard. -- Options: Remote control and drum storage kit. -- Also available in Single Phase.

EXTREMA DC-3075.3 TYPHOON Fabric Filtration Modular Dust Collection System.With 1-micron dust filtration efficiency this collector will make your shop cleaner, healthier, and more productive. -- (3) Fabric filter top bags are mounted above individual plastic collection bags. -- The multi-bag system is placed on sturdy steel legs in a horizontal series. -- 4,550 CFM Output with single-stage blower. -- Additional filtration sections can be easily added. -- Heavy Duty 7.5 HP motor with push button control and motor starter, 12" inlet. -- 13.5" Steel blower fan impellers are dynamically balanced. -- Collection bag snap-in rings for easy installation and removal of bags. -- Filter bags filter out dust particles down to (1) Micron in size; 6 mil thick plastic bottom collection bags are standard. -- Options: Remote control and drum storage kit.