EXTREMA ET-160 Fixed Spindle Shaper;"Extremely" Well-built and with solid features.Specifications: -- Solid spindle of 1-1/4" with 5-13/16" under the nut. -- Large 10 HP motor. -- (3) Spindle speeds of 5,500 - 7,500 & 10,000 RPM. -- Heavy cast iron table with a 12-3/8" max. table ring. -- Spindle lock, micro-adjustable back fence, and reversing switch. -- Miter gauge, cutterhead guard assembly, operator's manual, and tool kit.

EXTREMA XP-615AZ Single Sided Head PlanerSpecifications: -- Width: 24" -- Main HP: 15 HP -- Feed HP: 1 HP -- Elevation HP: 0.5 HP -- Max. Thickness: 8.75" -- Min. Thickness: 0.375" -- Max. Cut: 0.25" -- Min. Length: 10.5" -- Cutterhead Speed: 6000 RPM -- Feed Speed: 20-42 ft/min -- Air Requirements: 1000 CFM -- Thickness Adjustment: PLC ControllerBed Roller Adjustment: External -- Powered Bed Rollers: Top and Bottom -- lnfeed Roller: Standard -- Amps (230V / 460V): 41A/20A -- Weight: 2345 LbsFeatures: -- Solid cast-iron construction -- Sectional infeed rollers -- Huge 8-3/4"thickness capacity -- 6000 RPM cutterheads -- Anti-kickback fingers -- Segmented chip breakers -- Sectional feed rollers -- XP-615 Digital Controller -- Motorized table elevation -- Available with straight, STEALTH, or ilECTDFi cutterheads -- Heavy duty screwjack elevation system -- Easy access internal workings -- External bed roller adjustmentsOptional: -- In-feed Roller

EXTREMA - DCY-1220 L3 TYPHOON: Cyclone Filtration Dust Collection System. -- Powerful 2-stage dust collection drops out heavier dust particles through a Rotary Air Lock, allowing you to choose the disposal system before passing finer particles through the fan and filter. -- Air volume rated @ 8,800 CFM. -- Unit includes: 20 HP Motor with a Soft Start already wired in. -- Rotary air lock with: 1 HP Motor @ 38 CFM. -- Low noise operation. -- Standard support frame: LEG 3; 164" clear height x 149" clear width x 91" clear depth. Includes after filter Baghouse DC-327E. Features: 16" Inlet; (3) sections with (9) socks per section. -- Filter Socks: 6" Dia. x 70-7/8" for greater air-to-filter ratio; (1) micron filter. -- Unit is enclosed.

EXTREMA XF-DC4 Power Feeder w/Mounting ColumnExtrema has a wide range of power feeders that range from compact junior feeders to large 5-roller feeders. The XF-DC4 Series features a 4-roller system with variable speeds. Includes the 2/3 HP DC brushless servo motor for higher torque and better variable speed control than a 1HP AC motor.Specification: -- "EXTREMELY" Heavy duty 4-Roll Power Feeder with 4-3/4" & 2-1/4" rubber rollers. -- 2/3 HP Motor with forward/reversing switch. -- Variable speed from 7-72 FPM -- Heavy duty cast aluminum construction of the feeder housing. -- Cast iron stand components with fully adjustable mounting column. -- 3/4" Flotation of rollers for material thickness variations. -- Standard reach from base is 720 mm / 28-3/8" (optional 850 mm / 33-7/16" arm available)

"EXTREMA XF-54T.1 Power Feeder w/Mounting Column;EXTREMELY" Heavy duty 5-roller continuous belt Power Feeder with (3) 44.5" x 1/2" tracks. -- 1 HP Motor with forward/reversing switch. -- (4) Speeds of 15 - 28 - 39 & 78 FPM. -- Heavy duty cast aluminum construction of the feeder housing. -- Cast iron stand components with fully adjustable mounting column. -- 3/4" Floatation of the rollers. -- Standard reach from base is 720 mm / 28-3/8" (optional 850 mm / 33-7/16" arm available)

EXTREMA XF-34.1 Power Feeder w/Mounting Column;EXTREMELY" Heavy duty built 3-Roll Power Feeder with 4-3/4" dia. and 2-1/4" wide rubber rollers. -- 1 HP Motor with forward/reversing switch. -- (4) Speeds of 13 - 26 - 36 & 72 FPM. -- Solid cast aluminum construction of the feeder housing. -- Cast iron stand components with fully adjustable mounting column. -- 3/4" Floatation of the rollers. -- Standard reach from base is 720 mm / 28-3/8" (optional 850 mm / 33-7/16" arm available).

"EXTREMA XF-34.3 Power Feeder w/Mounting Column;EXTREMELY" Heavy duty 3-Roll Power Feeder with 4-3/4" & 2-1/4" rubber rollers. -- 1 HP Motor with forward/reversing switch. -- (4) Speeds of 13 - 26 - 36 & 72 FPM. -- Heavy duty cast aluminum construction of the feeder housing. -- Cast iron stand components with fully adjustable mounting column. -- 3/4" Floation of the rollers. -- Standard reach from base is 720 mm / 28-3/8" (optional 850 mm / 33-7/16" arm available)

EXTREMA XF-38.1 Power Feeder w/Mounting Column;"EXTREMELY" Heavy duty 3-roll Power Feeder with 4-3/4" & 2-1/4" rubber rollers. -- 1 HP Motor with forward/reversing switch. -- (8) Speeds of 7 - 13 - 18 - 22 - 26 - 36 - 43 - 55 & 108 FPM. -- Heavy duty cast aluminum construction of the feeder housing. -- Cast iron stand components with fully adjustable mounting column. -- 3/4" Floation of the rollers. -- Standard reach from base is 720 mm / 28-3/8" (optional 850 mm / 33-7/16" arm available)

EXTREMA XF-38.3 Power Feeder w/Mounting Column;"EXTREMELY" Heavy duty 3-Roll Power Feeder with 4-3/4" & 2-1/4" rubber rollers. -- 1 HP Motor with forward/reversing switch. -- (8) Speeds of 7 - 13 - 18 - 22 - 26 - 36 - 43 - 55 & 108 FPM. -- Heavy duty cast aluminum construction of the feeder housing. -- Cast iron stand components with fully adjustable mounting column. -- 3/4" Floation of rollers for material thickness variations. -- Standard reach from base is 720 mm / 28-3/8" (optional 850 mm / 33-7/16" arm available)

EXTREMA XF-3J Power Feeder w/Mounting Column;3-Roll Power Feeder with (3) rubber feed rollers. -- 0.25 HP Single phase motor. -- (4) Speeds of 20 - 26 - 33 & 43. -- Cast aluminum construction of the feeder housing. -- Heavy cast iron Universal Stand components. -- 1/2" Flotation of the rollers. -- Fully adjustable Mounting Column w/locking joints.

EXTREMA XF-44.1 Power Feeder w/Mounting Column;"EXTREMELY" Heavy duty 4-roll Power Feeder with 4-3/4" & 2-1/4" rubber rollers. -- 1 HP Motor with forward/reversing switch. -- (4) Speeds of 13 - 26 - 36 & 72 FPM. -- Heavy duty cast aluminum construction of the feeder housing. -- Cast iron stand components with fully adjustable mounting column. -- 3/4" Flotation of the rollers. -- Standard reach from base is 720 mm / 28-3/8" (optional 850 mm / 33-7/16" arm available)

EXTREMA XF-44.3 Power Feeder w/Mounting Column;"EXTREMELY" Heavy duty 4-Roll Power Feeder with 4-3/4" diameter x 2-1/4" wide rubber rollers. -- 1 HP Motor with forward/reversing switch. -- (4) Speeds of 13 - 26 - 36 & 72 FPM. -- Heavy duty cast aluminum construction of the feeder housing. -- Cast iron stand components with fully adjustable mounting column. -- 3/4" Flotation of the rollers. -- Standard reach from base is 720 mm / 28-3/8" (optional 850 mm / 33-7/16" arm available).

EXTREMA XF-54T.3 Power Feeder w/Mounting Column;"EXTREMELY" Heavy duty 5-roller CONTINUOUS BELT Power Feeder with (3) 44.5" x 1/2" tracks. -- 1 HP Motor with forward/reversing switch. -- (4) Speeds of 15 - 28 - 39 & 78 FPM. -- Heavy duty cast aluminum construction of the feeder housing. -- Cast iron stand components with fully adjustable mounting column. -- 3/4" Floatation travel of the rollers. -- Standard reach from base is 720 mm / 28-3/8" (optional 850 mm / 33-7/16" arm available)

EXTREMA PERFORMA XS-2P52 Wide Belt Sander (2) Heads;52" Width cap. Drum, Roller and Platen - 75"; Belt Lengths Head Configuration: -- 1st Head: Contact drum 30 HP motor; -- 2nd Head: Roller and Platen 30 HP motor.Features: -- Over thickness safety device -- Infeed bed rollers -- Digital thickness controller -- Individual amp meters -- Disc brakes on sanding heads -- Telemecanique electrics. -- Camozzi pneumatics -- Variable speed drive system.Specification: -- Feed motor 3 HP -- Elevation motor 0.5 HP -- Max. thickness 6" - Min. thickness 1/8" -- Contact drum 1st head 8" dia. -- Roller drum on 2nd head 5" dia. -- Dust Collection requirements 4800 CFM -- Feed speeds 15 - 50 FPM. -- Weight 6500 Lbs -- AMPS (220 V / 460 V ) 148/74.

EZ SANDER EZ-3760 Wide Belt SanderEZ-Sander's are built to with the ability to hold very tight tolerance (+/-.003) side to side when set up properly.Specifications: -- The sanding head is a combination head that consists of a 5" rubber-covered contact drum for the more aggressive sanding and then followed by an adjustable 2-1/2" graphite-covered felt polishing platen for doing very fine finishing sanding using a 37" X 60" abrasive belt. -- The conveyor belt speed is set to run at 10 - 30 FPM and is controlled via AC variable speed unit mounted in the main control panel. Simply adjust the dial setting to your desired feed speed. -- Double infeed and outfeed hold-down rolls are provided to help ensure proper part feeding through the Sander. -- The conveyor table/bed opening has a 0" to 5" opening allowing the operator to sand some parts as thick as 5" and the ability to sand very thin parts as well. -- Power raising and lowering of the conveyor bed is standard. -- Digital thickness display is standard.Complete with & Features: -- EZ Sander is equipped with a state-of-the-art electronic tracking system for the abrasive belt. -- Emergency stop heavy-duty caliper disc brakes bring the sanding head to a stop within 4 to 5 Sec when activated by the machine's safety interlock system. -- Limit Switches on both sides of the abrasive belt to keep the belt from over-travel. NOTE: -- Available in single phase with a 7.5 HP or 10 HP 3-Phase main drive motor. -- Voltage change to 440 Volt ...$275.

Cabinet Door Finishing System --4 Air Spray Guns --3 different lines and pumps --Paper feed belt with various speed options --Infrared sensors detect exact measurements of cabinet doors or mouldings and spray only the pieces being sent through. --System includes: (1) Dry Room and fan for air movement. --System is in great condition and works well. Our shop got to the point where we were really only using it to prime doors and it is capable of so much more than that.

FANUC - S430iW, ...RobotFANUC Robot for palletizing rectangular compressed bags.Specifications -- (6) Axes. -- Payload: 165 kG (255 Lbs). -- H-Reach: 2,643 mm (104"). -- Robot mass: 1,300 kG (2,860 Lbs). -- Complete with: Pendant control. -- Complete with: Gripper type arm and pallet gripper. -- Refurbished with (90) days Warranty. -- Buyer to install safety guards.NOTE: Machine was rebuilt is 2021.

HOLZ-HER CUT 6120 FRONT LOAD, AUTOMATIC PANEL SAW: -- Specifications: 3,900 mm (153.5") Max. rip cut cap., 3,900 mm (153.5") pull back pusher stroke; 82 mm (3.2") saw blade projection.15 HP (11 kW) Main saw motor, 1.5 HP (1.1 kW) scoring motor. -- Saw Carriage:Variable feed speed from 3 - 320 FPM (1 - 100 MPM ), return speed of 416 FPM (130 MPM).Motorized bi-directional grooving capabilities with electronic adjustment for 0 mm - 35 mm.Automatic cutting length limiter adjusts the cutting height & cutting length at the end of the workpiece. -- Pusher Fence:(7) Material gripper clamps, (1) Double Finger mounted at the cross-cut fence location for narrow strip cutting & (6) standard clamps. 82 FPM (25 MPM) forward positioning speed, 328 FPM (100 MPM) return speed.Variable pressure settings for delicate materials. Pressure beam has an integrated "Last Cut" operation to achieve a "0" mm panel dimension.Rack & pinion movement on both sides to assure the pusher remains parallel. -- Operator & Machine Control:PC Front-End with "CUTCONTROL 2" + "EASY-PLAN" + Windows operating system,19" TFT Display with unlimited program storage; keypad for data entry, USB & RS-232 serial port, "CUTCONTROL 2" offers Real-Time 3D Moving Graphics, diagnostic for errors or machine malfunction by means of an error signal code, incremental or absolute programming in mm or inches."CUTCONTROL 2" allows the operator to easily input information for absolute, serial, format, grooves, perforations, & position cutting which allows the machine to easily adapt to various situations & materials."Opti-Cut" & "EASY-PLAN" is a very user friendly on-board Optimizing System for all types of various cutting patterns, including angled cutting -- Complete with: Non-Marking rear roller support rails: Solid Air Cushion Table before & after the cutting line, ensures easy panel handling. Pneumatic crosscut side aligner, adjustable from 0" - 82.6" (0 - 2,100 mm). Side aligner is "Fully Automatic" adjustment when panel is less than 1,300 mm (51")"Quick Change" Blade system with automatic saw blade height adjustment; Electronic positioning of the scoring blade through the NC control.(3) Adjustable via "pneumatic locking" air support tables, ea. 70.8" x 23.6" (1,800 x 600 mm); -- Actual Model is HOLZ-HER CUT 6120 Dynamic

HOLZ-HER - 1435-SE EDGEBANDER"1906" Cartridge Glue System; 5 mm edge thickness cap. (up to 8 mm w/optional tooling); automatic magazine coil & strips; 3 mm PVC cap. pneumatic guillotine for coil cutoff. Workstations: -- Double-motor end trim, (2) 0.3 HP - 9,000 RPM motor ea.; chamfers 0° - 10°. -- Universal top & bottom fine trim (for bevels from 0° - 15°); allows simultaneous bevel & profile trimming; (2) 0.8 HP - 18,000 RPM motor ea.; all trim motors are 0.6 kW HF - 300 Cy. -- Top & Bottom PVC scraper unit for 0.8 - 5 mm radius; air jets for blowoff. -- Top & Bottom "jump" buffing (0.3 HP - 1,620 RPM ea.). -- Single feed speed: 35 FPM.Complete with: Built-in Operator Control Panel; outboard panel support; frequency converter; used tooling; and sound enclosure.

HOLZ-HER 1402 HF Compact EdgebanderFeatures: -- Cartridge glue system, 3 mm edge thickness cap., -- Semi-automatic feed magazine, coil stock feeds automatically with guillotine cutoff, all strip stock is fed manually with pusher bar to advance the edging. Digital glue height indicator.Workstations: -- Double motor end trim (1 HP - 10,500 RPM motor ea.) -- Universal top & bottom fine trim (1942M) for bevels from 0° - 15³; allows simultaneous bevel & profile trimming (1 HP - 18,000 RPM motor ea.; trim motors are 0.6 kW HF - 300 Cy). -- Top & bottom PVC scraper unit (1929) for 0.8 - 3 mm radius. -- Top & bottom buffing (1940), 0.3 HP - 1,620 RPM motor ea. -- Single feed speed of 35 FPM. -- Complete with: Fixed outboard panel support, frequency converter, sound enclosure, and used tooling.