Veneer Equipment For Sale

The seller has confirmed that these (2) Amitec VT veneer slicers are in good working/running condition. They are ready to load! - (2) Available - Slices log cants in the lengthwise direction - Compares to the Marunaka SL-250 - 9-7/8" (250mm) Max lumber slicing width: With up to 9-7/8" high cant, veneer thickness 1/25" to 3/8". 75° knife angle with 18 ° knife bevel - Knife length: 46-1/2" (1,180mm) - Motorized upper feed beam with Continuous belt feed - Variable speed: 120-180FPM (40-60 m/min) - 30HP feed motor - Head elevator: 1HP - Approximate weight: 16,000 lbs - 327"L x 62"W x 75"H

102" Width cap. Veneer Clipper completely reconditioned to modern mechanical and safety standards to meet todays manufacturing needs. Original machine frame will be fully disassembled cleaned and repainted. The frame is the only part of the original machine used and all components are upgraded.Mechanical upgrades include:1. 2-Hand anti-tie back push button cycle activation 2. Photo safety eyes located on both front and back side of blade3. Full safety guarding including a fully enclosed knife section 4. New electric motor and gear box main drive system5. New knife and shear bar6. All new electrical/control box with Components and Wiring7. All new upgraded bearings including replacing Babbitt bearings Machine comes with a full (1) year warranty

There are (4) machines at this facility. Two are used in production and the other two are in storage. 87" Capacity

Italpress Matrix membrane-less press. See photos for specifications. Heating platen dimensions................................ 1,450 x 2,800 mm (57" x 110") Maximum useful lamination area........................1,250 x 2,600 mm (49" x 102") Maximum work piece thickness ......................... 43 mm (1.7") PVC foil width...................................................... 1,420 -1,450 mm (55.9" - 57") Maximum laminating pressure..............................200 metric tons (220 US tons) Maximum platen temperature................................ 150° C (302° F)

LANGZAUNER G-5920 Cross-Cut Guillotine. Specifications: -- 35.5" Blade hydraulic pressure bar and knife; -- 5 Gal tank, pump is driven by 1.5 HP motor.Complete with: -- 2-Hand operation or foot pedal, Emergency-Stop, (3) photocells for safety, -- All safety guards per international standards.

--Make an Offer!--Liquidation Surplus Machine-- OMPEC TRO/10/R50 TYPE CE 3200 10-1/2' Hydraulic Veneer Guillotine, with 10° Cut & 50 mm (1.97") Fence Teeth Specifications: Max. cutting length 3,250 mm (127.95"), Nominal cutting length 112". Cutting width 23 - 1,020 mm (0.91" - 40.16"). Max. cutting height 80 mm (3.15"). Table height 950 mm (37.40"). Equipped with: 7.5 kW (10 HP) Hydraulic motor. Motorized parallel back fence, with 1/2 HP Motor, Digital readout, & Hand wheel for fine adjustment, and Parallel rack & pinion guides. 2-Handed operation & Safety light curtain. Complete with: Manual. Replaceable cutting pads. NOTE: Very well maintained, though machine has been stored outside under tarp, thus some surface rust can be expected.

RAIMANN Model ASA 1650, Veneer Patcher.Specifications: -- 61" Throat cap., 3 HP gear motor with new/rebuilt drive unit, strip type mechanical plug-feeder mechanism - cap. of up to (40) plugs/Min.; -- Thickness of veneer patchable 1/32" - 1/5" (0.08 mm - 0.2 mm) (softwoods), 1/20" - 3/16" (hardwoods). P-34 dies. -- Tool sequence: Veneer patch is cut by the table die and scrap is ejected into discharge chutes, veneer patch blank is then positioned against the underside of the table die, plug punch cuts replacement veneer patch from underside and patch is inserted into the proper position. -- Reconditioned by experts. -- Overall size: 10' 8" (3,250 mm) Length x 67" (1,700 mm) height; approx. weight 12,000 Lbs (5,450 kG). -- Optional Glue applicator add ...$9,975. -- Optional strip feeder add ...$6,750.Actual model is RAIMANN Model ASA 1650

SAVI HFK-250 Veneer Guillotine; General Specs: -- 102.4" (2,600 mm) Width cap., 4" daylight opening, hydraulically operated knife, 4 HP Leroy-Somer motor powers hydraulic unit with reservoir. -- Originally fitted with motorized parallel fence with 0.5 HP two speed gearmotor drive, push button operated, adjustable from 1" - 50" with magnified tape reader in front of machine. -- Equipped with: 2nd Cut feature with automatic reset, laser guide line light, photoelectric barrier guard for knife & hold-down beam, 2-hand operation of knife cycle. -- Note: Rear fence has been removed or modified. Shaft has chain/sprocket.

--In Auction--Starting bid: $100-- Schuetz Tool Bladder Press Specifications: (2) Shuttle tables, approx. 55” x 106” press capacity. Hot air design with 3mm silicone membrane to press veneer into profile, typical cycle time 3 minutes using proper glue that sets at 200°F. Can use PVA which would extend cycle time to approx. 15 > 45 minutes depending on the actual glue mix used to achieve 80%+ cure strength. Includes Hydraulic Pump. SPECIAL NOTE: Fully operational, however, need 4 or 5 heating rods replaced, new rod parts are included for you to install ( don't have the capability to remove them). The current average operational temperature is 150° F. NOTE: Above specs are taken from literature and thought to be accurate. As always please take advantage of the inspection period to verify. Items seen in the background are NOT a part of this Lot.

Schuetz Tool Bladder Press Specifications: (2) Shuttle tables, approx. 55” x 106” press capacity. Hot air design with 3mm silicone membrane to press veneer into profile, typical cycle time 3 minutes using proper glue that sets at 200°F. Can use PVA which would extend cycle time to approx. 15 > 45 minutes depending on the actual glue mix used to achieve 80%+ cure strength. Includes Hydraulic Pump. SPECIAL NOTE: Fully operational, however, need 4 or 5 heating rods replaced, new rod parts are included for you to install ( don't have the capability to remove them). The current average operational temperature is 150° F. NOTE: Above specs are taken from literature and thought to be accurate. As always please take advantage of the inspection period to verify. Items seen in the background are NOT a part of this Lot.

VAC-U-CLAMP FT-1000 52" x 123" Dual Shuttle Table Thermofoil Vacuum Press Overall OEM Specifications: Typical cycle time 5.5 - 7 Min. averaging 7 - 8 Cycles/Hr., Approx. conservative production with 18 Parts/Cycle & 126 Parts/Hr., 1,000 Parts/Day, 5,000 Parts/Week. Table Configuration: (2) Shuttle tables (when one table is in press oven, other table is being loaded or unloaded), Table entry & exit completely automatic & powered by CNC-controlled gear-driven stepper motor. Construction: TIG-welded aluminum tubing covered with 18 GA steel covers that have been powder coated for durability, Aluminum platen easily removable for cleaning if necessary, Easy-access table 36" H. Heating: (24) 1000 W Quartz infrared type lamps, Infrared thermocouple for accurate reading film temperature. Features: Automatic film pressure bar opening/closing connected to safety circuit preventing table movement if bar is not completely closed, Automatic high pressure cooling air as tables exit from oven, Tempered glass viewing window with 300 W Interior halogen light. Includes: 45 CFM Vacuum Pump capable of producing near absolute vacuum (14.7 PSI, 29.9 in. Hg.), 30 Gallon ASME-certified vacuum reserve tank for rapid evacuation & decrease of cycle time, Vacuum lines rated for 3,000 PSI. Operator Controls: OMRON PLC Control, with Color touchscreen display, (5) Storage bays for different film type programs, & Remote access through built-in remote wireless modem. Complete with: (2) 61” W 3-tiered double-sided steel roll racks, Each with (2) Locking swivel & (2) Swivel 3-1/4” Dia. x 1” W Casters, Rack dimensions 76" x 32" x 41" H. NOTE: (1) Shuttle Table Not Installed & in Crate. CURRENCY NOTE: Negotiable Price is listed in U.S. Dollars.

Vac-U-Clamp FT900 Thermafoil mPress Brand new - Seller never used it!

Vac-U-Clamp FT800+ Thermofoil Press 52" x 105" Work area Dispenser Rack (3) Vac bags new in boxes still

The Vantec 2800mm Spindleless Veneer Lathe is designed to process veneer for plywood production from both hard and soft logs. Its metal tempered grooved rollers and lathe knife inclination system work perfectly to make sure there will always be a precise contact area between the lathe knife and the log during the peeling process by eliminating vibration that could cause damage to the Veneer sheets. Vantec Spindleless lathe proves its efficiency by delivering consistent thickness variation and a impressive top linear speed of 180 m/ min throughout the peeling process for face or core veneers with smooth surfaces. - Log diameter up to 600 mm; - Max log length: 2750 mm; - Min log Length: 2300mm; (with stacker) - Min log length:1800mm (no stacker); - Veneer thickness: 1.0 to 4.0 mm; (Pine and eucalyptus); - Log core after peeling: 40 to 45mm; - Maximum linear speed 180 m/min; - Drive panel included; - Each motor is individually connected by a Variable Speed Drive for torque control in two points of traction on the rollers to pre- vent excessive load on tip ends; - Log Central aligner with maximum of 2200 mm of movement; - Pneumatic scriber Knives (02 fitted on the sides to cut in width and 01 in the Center to cut the length); - Width: 7640 mm; - Length: 3400 mm; - Height: 2550 mm; - Approximate weight: 14000 kg.

The Vantec Automatic Rotary clipper is designed to clip 2800 mm veneer sheets into specific sheet sizes as per the auto stacker preselection. It comes with electronic drive panel, automatic gauge system, positioning of clipper knife by Servomotor and encoder. It is de- signed to work with one tensioned clipper knife with gear motor. It also comes with a 2 HP motor on the output. The clipper knife is not included. - Veneer Thickness : 1 to 4 mm; - Max. Log: 2.750mm; - Minimum veneer width cut: 800 mm; - Max. Veneer length cut: 2700 mm; - Min. Veneer length cut: 700 mm; - Min. Venner rounding length: 150 mm; - Rotor gear motor: helical gears; - Clpper rollers power drive: 4 hp 6P; - Outlet conveyor Motor: 2hp 4P (input) 1 hp 8P (output); - Clipper Servomotor: 40 Nm (2x); - Width: 4800 mm; - Length: 6000 mm; - Height: 1700 mm; - Approximate weight: 7.000 kg

The Vantec Veneer Auto Stacker, ELV 1.82B is a Vacuum stacker for 2800 mm Veneer lathe. It is fitted with double stacking system (04 bins), with four veneer transport lines and four 5hp exhausters. with of two stoppers and eight ejecting arms. With drive Panel, VSD for exhaust fans and hydraulics lifting tables. Min veneer sheet length sheet: 2300 mm; • Max veneer sheet length sheet: 2700 mm (or Two sheets of 1350mm); • Min veneer sheet width: 800 mm; • Max veneer sheet width: 1500 mm; • Max height of stacks: 1000 mm; • Exhaust motor: 10 hp 4P (8x); • Inlet conveyor motor: 2hp 8P; • Transport conveyor motor: 6hp 4P; • Hydraulic pump motor: 5hp 4P (3x);

Wemhoner Variopress