Woodworking Equipment For Sale

EXTREMA PERFORMA XS-2P52 Wide Belt Sander (2) Heads;52" Width cap. Drum, Roller and Platen - 75"; Belt Lengths Head Configuration: -- 1st Head: Contact drum 30 HP motor; -- 2nd Head: Roller and Platen 30 HP motor.Features: -- Over thickness safety device -- Infeed bed rollers -- Digital thickness controller -- Individual amp meters -- Disc brakes on sanding heads -- Telemecanique electrics. -- Camozzi pneumatics -- Variable speed drive system.Specification: -- Feed motor 3 HP -- Elevation motor 0.5 HP -- Max. thickness 6" - Min. thickness 1/8" -- Contact drum 1st head 8" dia. -- Roller drum on 2nd head 5" dia. -- Dust Collection requirements 4800 CFM -- Feed speeds 15 - 50 FPM. -- Weight 6500 Lbs -- AMPS (220 V / 460 V ) 148/74.

EZ SANDER EZ-3760 Wide Belt SanderEZ-Sander's are built to with the ability to hold very tight tolerance (+/-.003) side to side when set up properly.Specifications: -- The sanding head is a combination head that consists of a 5" rubber-covered contact drum for the more aggressive sanding and then followed by an adjustable 2-1/2" graphite-covered felt polishing platen for doing very fine finishing sanding using a 37" X 60" abrasive belt. -- The conveyor belt speed is set to run at 10 - 30 FPM and is controlled via AC variable speed unit mounted in the main control panel. Simply adjust the dial setting to your desired feed speed. -- Double infeed and outfeed hold-down rolls are provided to help ensure proper part feeding through the Sander. -- The conveyor table/bed opening has a 0" to 5" opening allowing the operator to sand some parts as thick as 5" and the ability to sand very thin parts as well. -- Power raising and lowering of the conveyor bed is standard. -- Digital thickness display is standard.Complete with & Features: -- EZ Sander is equipped with a state-of-the-art electronic tracking system for the abrasive belt. -- Emergency stop heavy-duty caliper disc brakes bring the sanding head to a stop within 4 to 5 Sec when activated by the machine's safety interlock system. -- Limit Switches on both sides of the abrasive belt to keep the belt from over-travel. NOTE: -- Available in single phase with a 7.5 HP or 10 HP 3-Phase main drive motor. -- Voltage change to 440 Volt ...$275.

Cabinet Door Finishing System --4 Air Spray Guns --3 different lines and pumps --Paper feed belt with various speed options --Infrared sensors detect exact measurements of cabinet doors or mouldings and spray only the pieces being sent through. --System includes: (1) Dry Room and fan for air movement. --System is in great condition and works well. Our shop got to the point where we were really only using it to prime doors and it is capable of so much more than that.

Fanuc Robot with Controller Box and Teach Pendant Model: S-420iF Type: A05B-1313-B501 Part #: R98Y03430 Date: 1998.11

45 KVA 480 volt to 208Y/120

Felder Format 4 Tempora 60.16L Edgebander

Felder Creator 950 Premium CNC Center

Felder Creator 950

Felder Format 4 Edgebander Model: Tempora 6012

Felder Format 4 Edgebander Model: Tempora 6012 Return conveyor is no longer available.

Felder Profit H10 CNC Router (2) Vacuum Pumps 7.5 HP Tool Changer Outfeed Conveyor

Felder Profit H10 CNC Router (2) Vacuum Pumps 7.5 HP Tool Changer Outfeed Conveyor

Large table size, extendable in all three directions by up to 39" (1,000 mm) without the requirement of tools. Comfortable one-handed lever operationHeavy-duty eccentric clamp, usable on the left and right-hand side.Specifications: -- 3 HP motor, tilting head, manual hand lever control for mortise length and depth; 13" x 22" table with eccentric clamp -- 3000 RPM, reversible motor that caters for left and right cutting bits and a solid quad-jaw chuck with clamping range from 0–20 mm -- Lateral range of motion is 250 mm, cut depth is 160 mm, available height adjustment is 130 mm and there are solid locking stops in all three directions for setting precise stops.Features: 2-Jaw chuck with 5/8" capacity, Dust control collection tray below the cutter out to an 80 mm outlet,Complete with (2) adjustable and removable extension wings; fence for 90° & 45° mortises, extended stop bar on each side of table.

FELDER FORMAT KAPPA 450 Sliding Table SawSpecifications: -- 126" (3,200 mm) cutting length w/scoring, anodized 14-3/4" x 126" aluminum sliding table with tracking by roller bearings, locks for easy panel loading in any position; 450 mm dia. main saw blade. -- Motorized raise, lower and tilting (0° - 45°) of blade with digital readout. -- Equipped with: -- 7.5 HP Main motor, 1.0 HP scoring motor unit w/external adjustment; square crosscut fence with (2) stops, standard rip fence with 1,250 mm (49") rip cap. w/digital readout; extension table with miter fence, and sliding outrigger support. -- Includes: -- (2) 4" Dia. dust outlets; swing away overarm saw guard.

Model G660 230V / 3Ph / 60 Hz With Premilling Automatic edge feeding

FELDER G-330 EDGEBANDER0.4 - 3 mm Edge thickness cap. and 40 mm panel thickness; 3" min. width and 4-3/4" min. panel length.Equipped with: -- Quick Melt Teflon coated glue pot for granular hot-melt adhesive. -- Heavy Duty guillotine for up to 3 mm thick PVC. -- Integrated Operator PLC controls and an LCD display. -- "Anti-slip" rubberized surface chain pads.Workstations: -- Single motor, Double Blade End Trim with HF motor - 12,000 RPM. -- Top & Bottom Flush/Bevel Trim, bevels 0° - 15° (0.5 HP motor - 12,000 RPM each). -- Open space at out feed . -- Single feed speed of 26 FPM.Complete with: -- Sound & Safety enclosure over trim stations and outrigger panel support, and used tooling.NOTE: Seller states that the equipment has less than 500 hours of use!

Photos coming! System includes: 24” in-line sander- Single head with buffing roller and clean up brush $340024” Double roll coaters 3ea-24” 2 bulb UV ovens 4ea24” Reverse rollcoaters 2ea24” 3 head brush denibber with double cleanup brushes 53” 2006 Heeseman sander- head 1 is a drum, head 2 is a cross belt, head 3 is a pad and has a clean up brush

There are (4) machines at this facility. Two are used in production and the other two are in storage. 87" Capacity

FIN - ST 1600, ...Top/Bottom Cleaning Brush.62" Width and 3-1/8" max. thickness opening, thickness adjustment by handwheel via worm gear with dial indicator.Equipped with: -- Top & Bottom nylon brushes driven by 3 HP drive motor (only 1-brush with machine). -- Separate variable speed feed motor with magnetic controls driving 3" dia. rubberized infeed & outfeed pinch rolls. -- Full fabricated sheet metal enclosure for efficient dust collection, dust enclosure hood with central 6" dia. dust outlet connection.

Manufacturer’s Specs. Hopper Feed 5 HP 5600 RPM Shaper Rotobelt Sanding Station 103” Triangular Belt Sander Air Blow Off Double Wheel Foiler Single Wheel Foiler