Woodworking Equipment For Sale

Komo VR508 CNC Router 60" x 120" Table 25 HP Sullair Vacuum Pump Dust Collector (10 or 15 HP - need to confirm) (2) Two main router heads with Quick Change (2) Vertical Drill Units (1) 8 HP 10" Saw Fanuc Control

KRAMER K2024-1U -- K20 Series system is a heavy-duty barrel tumbler with standard capacity of 4.80 cubic feet. -- K20 system is a deburring machine solution that features a timer, variable speed, a heavy chain drive, and removable, interchangeable barrels. -- This deburring turn-key machine can configured to handle (1) to multiple barrels at a time. The barrels are mounted in a cradle and can be interchanged to divide up the load. -- Includes (1) Unlined barrel -- Variable speed control 25 - 50 RPM; 24-Hour timer; Start-stop switch. -- Complete unit dimensions are 58" W x 32" D x 50" H.

The K14 Series system is a small, heavy-duty, bench-top, barrel tumbler with standard capacities ranging from 0.75 - 1.5 cubic feet. -- The K14 system is a deburring machine solution that features a timer, variable speed, a heavy chain drive, and removable, interchangeable barrels. -- The barrels are mounted high enought to allow a screen and pan underneath so the barrel can be emptied without lifting and dumping. -- This deburring turn-key machine can handle loads of up to 200 Lbs. The barrels are mounted in a cradle and can be interchanged to divide up the load. -- (1) Steel barrel lined with a durable Polyurethane lining; 14" diameter across corners by 22-1/2" wide; Quick action lock on covers, solid, watertight doors. -- Variable speed control 25 - 50 RPM; 24-Hour timer; Start-stop switch. -- Complete bench-top unit dimensions are 44-1/2" W x 25" D x 24" H.

KREG DK 3100 Electric 3-spindle Pocket DrillSpecifications: -- 1.5 HP Direct drive electric motor; 39-1/2" table/ top working height; (0.5 - 1) Sec cycle time. -- Drills (2) pocket holes in (1) machining cycle across rails of varying widths with 3/8" dia. step bit in (1) smooth operation. -- Drill spindles in the machine are fixed at 3/4" - 1" and 1-3/4" on center allowing it to handle most common rail widths of 1-1/2" up to 3-3/4" with ease. -- One of the (3) Spindles is with left-handed, simply remove one bit from the spindle not being used to set the desired 2-hole spacing. -- The bits are supported all the way to the workpiece by a hardened steel drill guide that ensures tear-out free holes and consistent placement in virtually any material.Features: -- 15ø Boring angle for greater stability, reduced screw breakout & splitting. This produces a smaller "flat-bottom" pocket hole with rounded sides that can be plugged with a dowel if desired.Includes: -- Pressure gauge, fence, hold down, and foot pedal control.

KREG KFT 4X8 Face Frame Assembly. -- American-Made 4' x 8' Frame Assembly Clamp with floor stand. -- Working surface at approximately 30° angle for convenience. -- Unit includes; (4) Overhead air cylinders mounted on an overhead beam adjustable up-and-down. -- Clamping beam that moves from left-to-right by means of rollers. -- Squaring bars (fences) on the bottom and both ends of the table. -- Clamping beam with an air filter/oiler/regulator and air outlet at lower end of the beam. -- Optional pneumatic screw gun & pneumatic flex hose.

KREG DK 5100 5-Spindle Pneumatic Pocket Hole Machine. -- Individually actuated motors, (5) 0.75 HP motors, mounted on 6" centers. -- Hardened steel drill guides to support drill bit through the operation; 1-touch, foot pedal cycle. -- Swings stops for optimized material positioning; dust collection chutes for efficient chip removal. -- Complete with pre-filter and automatic lubricator.

KREG DK 3100 Pocket Hole Boring MachineElectric 3-spindle Pocket Drill; 1.5 HP direct drive electric motor; 39-1/2" table/ top working height; (0.5 - 1) Sec cycle time. -- Drills (2) pocket holes in (1) machining cycle across rails of varying widths with 3/8" dia. step bit in (1) smooth operation.... Drill spindles in the machine are fixed at 3/4" - 1" and 1-3/4" on center allowing it to handle most common rail widths of 1-1/2" up to 3-3/4" with ease. -- One of the (3) Spindles is with left-handed, simply remove one bit from the spindle not being used to set the desired 2-hole spacing. -- The bits are supported all the way to the workpiece by a hardened steel drill guide that ensures tear-out free holes and consistent placement in virtually any material. -- Features: 15° Boring angle for greater stability, reduced screw breakout & splitting. This produces a smaller "flat-bottom" pocket hole with rounded sides that can be plugged with a dowel if desired. -- Includes: Pressure gauge & cycle counter, fence, holddown & clamping assembly, (2) 3/8" cobalt drill bits, and foot pedal control.

Electric Single Spindle Pocket Drill. Specifications: -- Capacity: Materials from 1/2"- to 1 1/2"-thick. -- 1.5 HP direct drive electric motor (also available 1.5 HP direct drive pneumatic motor); 40" table top working height; 1 Sec cycle time. -- Drills the pocket hole with a 3/8" dia. step bit in (1) smooth operation. The bit is supported all the way to the workpiece by a hardened steel drill guide that ensures tear-out free holes and consistent placement in virtually any material. -- Electrical: 110 VAC, Pneumatics: 90 PSI, recommended for clamping. -- Dimensions: 50"H x 24"W x 24"D (40" table height), 176 lbs.Features: -- 15° Boring angle for greater stability, reduced screw breakout & splitting. -- This produces a smaller "flat bottom" pocket hole with rounded sides that can be plugged with a dowel if desired. Includes: -- Pressure gauge & cycle counter, fence, holddown tower, (1) 3/8" cobalt drill bits, and foot pedal actuation.

Pneumatic Single Spindle Pocket Drill;Specifications: -- 1.25 HP direct drive pneumatic motor; 40" table top working height; (0.5 - 1) Sec cycle time. -- Drills the pocket hole with a 3/8" dia. step bit in (1) smooth operation. -- The bit is supported all the way to the workpiece by a hardened steel drill guide that ensures tear-out free holes and consistent placement in virtually any material. Pneumatics: 120 PSI recommended. Features: -- 15° Boring angle for greater stability, reduced screw breakout & splitting. This produces a smaller "flat-bottom" pocket hole with rounded sides that can be plugged with a dowel if desired. Includes: -- External regulator, filter & lubricator, (1) 3/8" cobalt drill bit, and foot pedal actuation. Just add $150 to the price of the machine for shipping.

Pneumatic Single Spindle Tabletop continuous operation drill;Specifications: -- 1.25 HP direct drive pneumatic motor; 8" tabletop working height; 1 Sec cycle time. -- Drills the pocket hole with a 3/8" dia. step bit in (1) smooth operation; the bit is supported all the way to the workpiece by a hardened steel drill guide that ensures tear-out free holes and consistent placement in virtually any material. -- Capacity: Materials from 1/2"- to 1-1/2" thick.Features: -- Pneumatic drill motor, pneumatic clamping. -- 15° Boring angle for greater stability, reduced screw breakout & splitting; this produces a smaller "flat-bottom" pocket hole with rounded sides that can be plugged with a dowel if desired.Includes: -- External regulator, filter & lubricator, 3/8" cobalt drill bit, and foot pedal actuation.Requires a compressor able to produce 8 CFM at 120 PSI (50% duty cycle).

Kremlin AIRMIX 15C25 Spray Pump perfect for painting small quantities of fluid products, water or solvent-based. Up to 90 bar of fluid pressure to compensate pressure drops.Specifications: -- (2) 5-gallon stainless steel covers/agitators, 3-way mixing valve for easy change-over, including hose. -- Pressure Ratio 15/1, Maximum Fluid Pressure 90 (1305) bar (psi), Maximum Air Pressure 6 (87) bar (psi) -- Air Consumption 2.8 (1.65) m³/h (cfm) -- Maximum Temperature 60 (140) °C (°F) -- Weighted Sound Level 71.2 dBA -- Recommended Air Pressure 2 - 5 (29 - 72.5) bar (psi) -- Fluid Output at 30 cycles/mn 0.75 (0.2) l/min (gal/mn), Fluid Output at 20 cycles/mn 0.5 (0.13) l/mn (gal/mn), Fluid Volume per Cycle 25 cc -- Free Flow Rate 1.5 (0.39) l/mn (gal/mn) -- Fluid Output at 15 cycles / mn 0.375 (0.01) l/mn (gal/mn) -- Air Consumption at 30 cycles/mn at 4 bar (60 psi) 2.8 m³/h (cfm), Displacement Per Cycle 25 (1.52) cc (cubic inch) -- Motor Type 245-4 -- Air Inlet F3/8 BSPP, Fluid Outlet F 3/8 NPS / M1/2'' JIC, Fluid Inlet F 1/2 BSPP / M26x125 -- Number of Cycles per liter of products 40 -- Height 57.5" x Width 32" x Depth 17", Weight 7.7 Lbs

Single belt oscillating "Tiltable Bed" 0° - 90° sander, 3 HP main motor, 3,400 RPM, belt size 6" x 89", 30.5" long platen. -- Max sanding length 30.5", 4" vertical adjustment of front table, 36" table height, oscillating rate of 121 times/min. -- Includes: (4) interchangable spindles, sizes are 1.25" - 1.5" - 2" & 2.5" dia.

KUFO SK-12RS Straight Line Rip Saw w/Return Conveyor;Entry level Straight-Line Rip Saw with a guaranteed 6' glue line. -- Powered by a 15 HP direct drive motor. -- 12" Dia. Blade capacity for up to 3-1/4" max. cutting height, 4,200 RPM blade speed. -- Equipped with (6) holddowns and a Wye-Delta soft start for lower amp requirements during start-up. -- 1 HP Feed motor, 36 - 145 FPM feed speed, 6" chain width and automatic chain lubrication. -- Treated chain links, pins and raceways withstand heavy use because of an automatic oiler. -- Large 15-3/4" rip capacity. -- Overarm control box mounted on the in-feed side. -- Total space requirements are about the same as a standard size tablesaw. -- Complete with side mounted return conveyor.

Oscillating Edge Sander with end sanding kit. -- 6" Wide x 89" long abrasive belt. -- Tilting 6" x 24" platen. -- 3 HP, single or 3-Phase motor w/emergency switch. -- 6" Diameter drive pulley. -- 8" x 24" Front table with a 4" vertical adjustment and miter gauge. -- End table for radius work. -- Heavy tables, fabricated steel base and dust hood. -- 3-Phase unit model # is SK-3000SDN3.

Kuka KR60-3 Robot System KR C4 Control System Kuka Programming Smart Pad Robot Enclosure (3) Heave duty conveyor racks

KUNDIG DUPLEX 53-RC-E Wide Belt Sander (2) Heads; 52" Width cap. Drum, Combination Head.Head Configuration1st Head: 7-1/4" Dia. rubber covered contact roll, 25 HP motor.2nd Head: Combination head with rubber covered contact roll and segmented finishing platen, infeed sensors sense the panel and electronically control the platen height with timers, variable edge control can also be set, 20 HP motor.Specifications: Abrasive belt size 54" x 75" with air tensioning and electronic abrasive belt tracking, both heads with abrasive grit thickness adjustment, 2 HP Variable feed drive. -- Conveyor belt speeds 9 - 45 FPM, controlled by electronic inverter & adjustable on the control panel; infeed & outfeed rubber covered holddown rollers.Equipped with & Features: -- Workpiece thickness cap. 1/8" - 6-1/4", motorized thickness adjustment with LED readout. -- A joystick controls the conveyor opening and start/stop of the feed, automatic "over-thickness" protection and automatic conveyor belt tracking. -- Constant passline of conveyor height at 35". -- Air blow off of second head abrasive belt. -- Emergency stop button, motor load meters, magnetic controls.NOTE from the seller: There is a small leak in the air bladder . The sander has 6,541 working hours

LA NUOVA SCOLPITRICE 201-16 Multi-Spindle Carving Machine.(16) Cutter Stations, 55" max. workpiece length,Specifications: -- (16) Dual carving spindle heads, 8" between spindles, 20" max. working diameter. -- Each head has a roughing & finishing spindle, all heads swivel 360° with pneumatic locking. -- Upper carriage controlled by (2) High Frequency changers allowing (2) motor speeds of 12,000 & 18,000 RPM. -- Pneumatic chucking of material, stock turns 360°. Copy stylus of hardened and ground steel, adjustable for depth on either side. -- Traverse feed of carving heads was patented and requires no maintenance. -- Includes: Lot of tooling. Table for flat/horizontal copying.Note: Machine completely gone over and all heads rebuilt in 2011 and used sparingly since.Actual model is 201-16.

V2000 60 x96TS-1VL-ONS-OCE-06PS Transportation Simulator Performs both rotary and vertical motions Designed for testing larger crates up to 60-in. by 96-in

LACEY-HARMER E-LINE Self-contained Visible Diode Laser End ShooterEconomical self-contained Visible Diode Laser; optics housed in a sealed cell to provide added protection against contaminants and moisture; nickel plated housing. -- Specifications: 100 Millampere operating current, -20° - +40° C operating temperature, 90 V for 250 nano-Sec mechanical stock. Beam angle with 5 mW - 15 mW output, 636 nm wave length. -- Options: 36" Long Diode Array Stand adjustable up to 90° from mounting surface, lines move easily and parallel to each other, micro-adjustment to make lines parallel, no tools needed -- Projects a line from approx. 12' to 15' depending on area lighting -- Consisting of two parts; (1) crossbar style mounting bracket, please add...$ 143; (2) axis slide brackets for easy positioning, add...$ 125 each or alteratively a simple universal stationary mounting bracket add...$ 30.

LACEY-HARMER LD-2002 Diode LaserEconomical self-contained Visable Diode Laser, optics housed in a sealed cell to provide added protection against contaminants and moisture; nickel plated housing. -- Specifications: 100 Millampere operating current, -20° to +40° C operating temperature, 90 V for 250 nano-sec surge protection. Beam angle 5 to 90 degrees, 5mW to 35mW output, 636 nm wave length for lines up to 20' projection. -- Options: 36" Long Diode Array Stand adjustable up to 90° from mounting surface, lines move easily and parallel to each other, micro-adjustment to make lines parallel, no tools needed. -- Optional items consist of: Crossbar style mounting bracket, please add...$ 90; axis slide brackets for easy positioning, add...$ 125 or alteratively a simple universal stationary mounting bracket, please add...$ 30.