Woodworking Equipment For Sale
2044 Results Found
$ 20,500
OLIVER 5385 Single Head Wide Belt SANDER (37") 1-Head and 37" belt width Combination Sanding Head with rubber covered contact roll and adjustable finishing platen, 1/8" - 5" Thickness capacity, 36" width capacity.Specifications: -- 20 HP Main drive motor. -- 1 HP Variable speed (15 to 45 FPM). -- 1/4 HP Power raising and lowering conveyor bed motor. -- 37" X 75"; Abrasive belts for longer life and less loading.Features; -- Central control panel features digital thickness set-up control for accurate stock height and removal. -- Four post lift design assures accurate consistent results. -- Oscillating belt is controlled by an air sensor to prevent sanding lines. -- Finishing Platen is fully adjustable and can be removed. -- Multiple dust ports for efficient dust management. -- Independent motors run the sanding belt, feed conveyor, and table elevation for maximum power to each operation.
$ 4,550
OLIVER 4705 SHAPER 5 HP, Sigle phase or 7.5 HP, 3-PhSpecifications and Features: -- Massive cast iron precision ground table provides a solid work surface. -- Cast iron base provides a steady platform. -- 3/4"; and 1-1/4"; interchangeable spindles are included for added versatility. -- Three spindle speeds allow more choices to produce a better finish. -- Reversing spindle gives more options for each set-up. -- Innovative dovetail design accurately raises and lowers the spindle. -- Fence is independent and features micro adjustments for quick set-up. -- Top mounted control panel includes a digital readout for spindle height. -- Large hand wheel for quick spindle height adjustment. -- Magnetic controls with emergency off switch for safer operation. -- Includes miter gauge. -- Spindle Speeds: 5,000, 7,000 and 10,000 RPM. -- Maximum Tool Diameter: 7"; Below Table, 8"; Above Table. -- Spindle Diameter: 1-1/4"; and 3/4"; Interchangeable. -- Vertical Spindle Travel: 4". -- Table Height: 36-1/2". T-Slot: 3/4" x 3/8". -- Dust Port Diameter: 4". -- 800 CFM min. -- Optional collet for router bits available special order --[1/2" Spindle for Models 4705 & 10047 Shaper]1/2" Spindle for Models 4705 & 10047 Shaper$89.99Model 10047[3/4" Spindle for Models 4705 & 10047 Shaper]3/4" Spindle for Models 4705 & 10047 Shaper$89.99Model 10047[1" Spindle for Model 4705 Shaper]1" Spindle for Model 4705 Shaper$99.99Model 4705[1/4" Collet for Models 4705 & 10047 Shaper]1/4" Collet for Models 4705 & 10047 Shaper$69.99Model 4705[1/2" Collet for Models 4705 & 10047 Shaper]1/2" Collet for Models 4705 & 10047 Shaper$59.99Model 4705[1-1/4" Spindle for Model 4705 Shaper]1-1/4" Spindle for Model 4705 Shaper$99.99Model 4705 prices may vary.
$ 15,999
OLIVER 4470 25" Shelix Cutterhead Planer; 10 HP motor Single Phase, or 15 HP 3-Phase motor. Full 25" of cutting width, over 9" of cutting capacity, and the ability to take up to 1/4" off in a single pass through , Byrd Shelix Cutterhead this planer will take whatever you can dish out. -- The Digital Thickness Controller and Powered Table Travel eliminate guesswork, make dialing in settings a breeze. But ease of operation isn't everything, this OLIVER outputs stock that's true and straight. -- A Sectional Infeed Roller and Chip Breaker apply uniform pressure on uneven stock, coupled with a Driven Outfeed Roller to keep your stock in place. -- And a powerful 10 HP motor Single Phase motor, or 15 HP 3-Phase motor.
$ 7,999
OLIVER 4455 22" Straight Knife Planer, 5 HP single phase or 10 HP, 3-Ph.The OLIVER "4455" Planer has a super-wide capacity, it'll handle stock up to 22" wide, and takes up to 3/16" off in a single pass.Specifications: -- 4-Knife HSS straight knife cutter head. -- A Sectional Infeed Roller and Chip Breaker apply uniform pressure on an uneven stock, coupled with a Driven Outfeed Roller to keep your stock moving smoothly. -- Add (2) feed speeds for extra quality, a Digital Thickness Guage for quick reference, and a powerful 10 HP motor. -- Max depth of cut 3/16" min part length 10"; Max work pc 22" w x 9" Thickness.
$ 4,400
OLIVER 4430 20" PLANER WITH HELICAL HEAD20" Maximum stock width cap., 1/4" to 8" max. stock thickness, 10" minimum stock length. Equipped with: -- 5 HP Main drive motor and mechanical raising and lowering of the cutter head. -- Fixed bed height of 29-7/8". Table dimensions 20"L X 21"W. Overall all table dimensions with infeed and outfeed bed extensions 51"L X 21"W. -- 3-1/4" Dia. Helical Cutter Head with 4-sided carbide inserts. -- Auto-Depth lock via nitrogen-charged cylinders eliminates snipping. -- 8" Max. thickness adjustment via handwheel includes LED Digital readout for head positioning. -- 4-Post support for proper head alignment.Complete with: -- 5" Dust outlet and built-in mobile base for ease of movement
$ 3,200
OLIVER 15" Planer with Helical Cutterhead - 10014, 3 HP (Single Phase)Unique design allows motor and cutter head to move in unison.Specifications: -- Auto-depth lock features twin nitrogen cylinders virtually eliminates snipping. -- Helical cutter head with premium carbide inserts. -- 4-Sided cutting inserts are indexed and easy to replace. -- Heavy cast iron construction including extension wings. -- Table and extensions wings are precision ground for smooth stock feeding. -- Table is fixed allowing easy use of auxiliary stock support. -- Wixey digital read-out allows precise thickness settings. -- Large handwheel and support struts allow easy height adjustment. -- Four-post design ensures head alignment regardless of stock thickness. -- Two-speed feed gearbox for better cuts, Oil bath gear lubrication for years of performance.Complete with: -- 4"; Port allows excellent dust management. -- Built-in mobile base allows easy movement in the shop. -- Magnetic switch for added protection and safety.
$ 9,995
22"; Planer with Byrd Shelix Cutterhead - 4455B, 7.5 HP shingle phase or 10 HP, 3-phBYRD Shelix carbide inserts are indexed for quick changing.Specifications: -- Max depth of cut 3/16", min. part length 10"; max. work pc dims 22" w x 9" thickness. -- (2) Adjustable Bed Rollers, plus one infeed and one outfeed roller. -- Cutterhead speed 5,000 RPM and head is equipped with (110) Byrd knife inserts. -- 2-Speed gearbox provides the perfect feed rate of 20 and 30 FPM.Features: -- Massive cast iron construction throughout. -- Polished built-in table roller assists movement of rough stock. -- Segmented infeed roller and sectional chip breaker easily handles rough stock. -- Magnetic controls with emergency off switch for safer operation. -- Digital readout allows precise thickness settings. -- Hinged access to cutter head and feed rollers for quick set-up. -- 3 V-belt drive smoothly transfers power to drive train and cutter head. -- Easy access to the motor, drive train, and gearbox assists in maintenance and adjustment. -- 5"; Dust chute easily handles chip removal (requires approx. 900 CFM) -- Powerful EFC motor available in single or three-phase. -- Single phase motor 7.5 HP, 220V Only (38 Amp)
$ 13,000
OLIVER 4470 25" Straight Knife Planer Full 24" of cutting width, over 9" of cutting capacity, and the ability to take up to 1/4" off in a single pass through the 4-knife standard cutter head, this planer will take whatever you can dish out. -- The Digital Thickness Controller and Powered Table Travel eliminate guesswork, make dialing in settings a breeze. But ease of operation isn't everything, this OLIVER outputs stock that's true and straight. -- A Sectional Infeed Roller and Chip Breaker apply uniform pressure on uneven stock, coupled with a Driven Outfeed Roller to keep your stock in place. -- And a powerful 10 HP motor Single Phase motor, or 15 HP 3-Phase motor. --OPTIONAL EQUIPMENT: Byrd Shelix Cutterhead (ADD $2,400)
$ 9,500
OLIVER - 299-D, ...24" Planer (8" thickness capacity) -- Capacity: 24" x 8" Thick planes stock as short as 11". -- 3-Knife steel cutterhead motor: -- 5 HP; 3 PH. -- Sectional infeed rolls: - (12) 2" Wide sections: Sectional chip breaker. -- (12) 2" Wide sections with: 1/4" Independent Lift. -- (2) Driven bed rolls; feed motor: 1 HP - 3 PH REEVES Variable speed 15 - 60 FPM.
Call for Price
OLIVER 2019 Wood Turning Lathe;This lathe brings the lathe back to the OLIVER line, in true OLIVER Fashion! -- Starting with a solid, stable cast iron base, legs, bed, tool rest, and headstock. -- OLIVER adds a powerful reversible 2 HP motor with a wide speed range for a variety of tasks. -- A frequency inverter and RPM Digital Readout give you an accurate read on your speed so you can precisely adjust for any particular job.Specifications: -- 41" Between Centers, 18" Swing over bed, 40" Swing Outboard; -- Spindle Speed 200 - 2,400 RPM, Front Faceplates 6". (2).Features: -- One of the best features on the lathe is the In-board and Out-board headstocks (slides on the bed), enabling you to work on very large Bowls and most anything else you need to turn. The slide extension can increase the center distance to 57" with optional extension bed.Includes: -- Integral spindle index for (36) positions.Dimesniosn/Weight: 46.5"long x 19.5" depth x 49.25" height. Approx. 415Lbs.Available Options: -- Bed extension that mounts in two positions....Protective Safety Guard. Assembly.... Please call. -- See attached literature for more specifications.
$ 9,950
OLIVER - 34-DD, ...Disc Sander (Double)(2) 30" Dia. steel discs; 5 HP double shafted motor turns @ 1,050 RPM.(2) Steel side tables, 40" x 15", (1) slotted and (1) plain; both tables tilt 10° up and 45° down.(1) Table with 6" manual vertical adjustment; rack travel adjustment by screw & crank. -- Complete with: Magnetic controls; (2) dust outlets; large handwheels for easy adjustments.
$ 9,500
OLIVER 299 Single Surface Planer;24" Width x 8" thickness cap., Cabinet Planer; -- 7.5 HP Cutterhead motor, and the OLIVER "ITCH" carbide cutterhead. -- 2 HP Gear box variable speed feed works with speeds of 15 - 60 FPM; sectional feed rolls, sectional chipbreakers. -- Complete with: Knife grinding equipment for OLIVER carbide cutterhead, knife setting device, top dust hood, quick set adjustment on bed rollers.One of the "Original" OLIVER Planers!
OLIVER 17"; SWING FLOOR DRILL PRESS17" Floor model Drill Press with a durable cast iron head, table and base.Equipped with: -- 3/4 HP motor, 240 to 3,400 RPM motor drives (16) different speeds making it suitable for heavy industrial use. -- The spindle is equipped with a heavy duty 5/8" capacity drill chuck on a MT-2 Morse taper. -- Spindle travel 3-1/8" -- Large 12" x 12" table with clamping slots. -- Rack and pinion system makes it easy to adjust the table up and down.
Call for Price
Call for Price
OMAB GRU-100 (BACCI Style) 4-Spindle Copy Lathe/ShaperSpecifications: -- Capacity: (4) Spindle duplicating/carving/copy heads with (4) copy belt sanders for asymmetrical parts. Max. working height: 6.5" (165 mm), max length capacity 39.4" (1000 mm). -- Speeds: (3) Carriage speeds: 3 IPM (75 mm/Min)_up to 7.87 IPM (200 mm/Min). Spindle speeds: 25 minimum to 42 maximum RPM. Features: -- Carriage feed motor 1.8 HP. Cutter drive motor 2.2 KW (3.9 HP). Bell cutters 1.38" (35 mm), Minimum working radius 0.71" (18 mm). -- Comes with: Installed cup-style cutters. -- NOTE: Larger diameters are possible by using every second carriage position, i.e. (2) heads instead of four heads. -- Dimensions approx 94" long x 37" wide x 78" High . Weight about 2400 lbs NOTE: Specifications are from similar BACCI lathes and need to be verified prior to purchase.
Call for Price
OMAL VELOX 1300 CNC BORE, GLUE & DOWEL INSERTER W/Optional LASER MEASURING SYSTEM: -- Specifications:PLC Controlled automatic step-by-step, boring, glue injection & dowel insertion into panel components, drawer parts, chair pieces, etc., at random spacing. -- Features:Auto Laser measuring device with Parametric Control. Touch Screen PLC control. -- Working Capacity:51" (1,300 mm) In X-axis work area, 1.57" Y-axis stroke with manual depth setting, 1.57" Z-axis stroke with manual vertical settings.10 mm to 40 mm (0.39" - 1.57") Material thickness capacity in the "Z" axis.The machine is currently set up for 8 mm dia. x 30 mm long max. dowel dimension. -- Work Areas:(2) Loading zones with a cycle time of one second for each bore, glue and dowel insertion when holes are on 32 mm intervals.Equipped with a brushless motor, ball nut and ball screw for quick positioning, -- Dowel Inserter:OMAL "SURE SHOT" revolver system guarantees a dowel is inserted every time. (1) Dowel insertion unit with 8 mm diameter dowel capacityStandard dowel dimension is 8 mm x 35 mm, Maximum dowel length is 40 mm, and maximum dowel projection is 14 mm. -- Operator & Machine Control:Touch Screen Control for writing and storing programs & is programmable in the "X" axis.Graphics programming 2.5D with simultaneous working display; Automatic Mirror-Image (left and right) programming; Parametric programming; Graphical aid.Internal self-diagnosis; Historical report of alarms, -- Complete with:(2) Working zones with, (1) horizontal drilling unit, (1) gluing unit, (1) dowel insertion unit. (1) 8-Liter cap. high-pressure glue tank, (1) 8-liter cap. water tank (for cleaning), (1) Vibratory Dowel Hopper, (4) pneumatic hold-down clamps, and Dual foot pedal controls. -- Options Include:Laser Measuring System, automatically measures the part, populates the program list of parts width & calculates all the inserting location for the part being processed. -- Actual Model is OMAL VELOX 1300
$ 29,800
OMAL - INSERT 900, ...CNC Point-to-Point Bore, Glue & Dowel InserterSpecifications: -- Capacities: X-Axis 900 mm (35.44"); Y-Axis 40 mm (1.57") stroke; Z-Axis 10 - 40 mm (0.39" - 1.57") thickness. -- Table size; 15-5/8"; x 49"; x 35"; H; (4) working zones: (2) 450 mm (17.72") W. -- Max. dowel size: 8 mm Dia. x 30 mm L (0.31" dia. x 1.18" L). -- Max. dowel projection: 15 mm (0.59"). -- Spindle speed: 6,000 RPM. -- Cycle time: 0.8 Sec.Equipped with: -- (4) 2-1/4" Dia. pneumatic hold-downs. -- (1) Horizontal drilling unit with: 3/4 HP - 3,380 RPM TEFC Motor; (1) glue injection unit & (1) dowel insertion unit. -- PC-Based controller with: 12" Display; (2) foot pedal controls.Complete with: -- BROVIND VIBRATORI "OB 300 DC": 14" Dia. x 5-1/2"; D vibratory Bowl Feeder with: "NC-02M-50 DC" Variable Speed Controller. -- (1) 8 L Cap. High Pressure Glue Tank; (1) 8 L Cap. Water Tank.
$ 29,700
OMAL HBD 2500 CNC BORE, GLUE & DOWEL INSERTER: Specifications: -- NC Controlled, automatic step-by-step boring, glue injection & dowel insertion into panel components: Drawer parts, chair pieces, etc. at random spacing or automatic hole-spacing with simple what-if statement: i.e. parametric programming.Working Capacity: -- 2,500 mm (98.4") In the X-axis; 30 mm (1-1/4") stroke in the Y-axis; 10 mm - 40 mm (0.39" - 1.57") thickness capacity in the Z-axis. (4) Working zones: Center fence and both side fences dropdown for 2- or large 1-zone operation.Tool Plate Configuration: -- X-Axis rack & pinion drive CNC Controlled; carriage speed of 90 MPM (295 FPM); Y- & Z-axis: Manual ball screw with digital indicators.Equipped with: -- (1) Horizontal drilling unit with: 3/4 HP - 6,000 RPM Motor; (1) gluing & (1) dowel insertion unit.Control System: -- PC Numerical Control operating system; Windows/XP, color video flat screen monitor; 40 GB hard drive; keyboard & mouse. -- Graphic operator inter-phase, parametric programming standard; OMAL patented "SURE SHOT" Revolver System with fiber optic sensor to guaranty reliable dowel presence & insertion.Complete with: -- (1) 18-Liter (4-3/4 Gallon) cap.; high pressure glue tank. -- (1) 18-Liter (4-3/4 Gallon) cap.; water tank (for cleaning). -- (1) Vibratory Dowel Hopper, (6) pneumatic hold-down clamps; machine is setup for 8 mm dowels.
$ 11,800
OMAL - INSERT 900, ...CNC Point-to-Point Bore, Glue & Dowel InserterSpecifications: -- Capacities: X-Axis 900 mm (35.44"); Y-Axis 40 mm (1.57") stroke; Z-Axis 10 - 40 mm (0.39" - 1.57") thickness. -- Table size; 15-5/8"; x 49"; x 35"; H; (4) working zones: (2) 450 mm (17.72") W. -- Max. dowel size: 8 mm Dia. x 30 mm L (0.31" dia. x 1.18" L). -- Max. dowel projection: 15 mm (0.59"). -- Spindle speed: 6,000 RPM. -- Cycle time: 0.8 Sec.Equipped with: -- (4) 2-1/4" Dia. pneumatic hold-downs. -- (1) Horizontal drilling unit with: 3/4 HP - 3,380 RPM TEFC Motor; (1) glue injection unit & (1) dowel insertion unit. -- PC-Based controller with: 12" Display; (2) foot pedal controls.Complete with: -- BROVIND VIBRATORI "OB 300 DC": 14" Dia. x 5-1/2"; D vibratory Bowl Feeder with: "NC-02M-50 DC" Variable Speed Controller. -- (1) 8 L Cap. High Pressure Glue Tank; (1) 8 L Cap. Water Tank. -- METROLOGIC "Voyager CG MS9540" Handheld Bar Code Reader.NOTE: Machine control is currently not operational; Seller believes it is its battery.
Call for Price
Single horizontal drill and dowel; 1300 mm work table with four fields; sure shot revolver system to guarantee the fastest cycle time, average one second, and extreme reliability; simple user friendly touch screen; heavy duty steel frame for maximum rigidity; large phenolic table with robust clamps suitable also for delicate materials; barcoding and ethernet ready; laser for measuring the part and populate the program;