Woodworking Equipment For Sale

Model P30N 600 V / 3 Ph / 60 Hz Includes Transformer

Paul AB920 Rip Saw Scanning Fenceless Infeed Infeed & Outfeed (not including decks) The machine has one fixed and 2 moving blades. The minimum distance between the moving blades is 44 mm (1.73"). The maximum distance between the moving saw blades is 210 mm (8-1/4"). The machine is designed for incoming boards with the following min./max. dimensions Length: 4' - 16' Width: 2" - 19" Ripped widths: 1.75" - 8" Thickness: 1" - 2" 480 Volt, 60 hz., 3 phase electrics 75 HP main motor Automatic edging separation after the saw Feed speed up to 300 fpm Fenceless infeed system with automatic skewing capability 16 width sensors on the infeed system

4 Head drill station 20' with powered roll case Hydraulic set stops

PHI IR-3 Preheater;Overall dimensions 5' wide x 4' long, consisting of: (3) IR Medium Wave heating banks, each 1" wide x 54" long, bank has gold foil quartz heating elements.This IR unit is designed to preheat the board to facilitate out gassing and help eliminate solvent pop and air bubbles in the coatings of deep pored materials such as oak. Also used to standardize board temps during colder months as well as decrease dry times of other substrates. These units are primarily (but not exclusively) designed for use before the application of stain and sealer coats. Features: Explosion proof electrics, electrical heat temperature adjustable from 100° - 150° F, variable feed speed from 8 - 30 FPM (2.5 - 9 MPM).

PILLAR MACHINE HPLD 96" CNC BORE & LOCK-DOWEL INSERTER: -- Specifications:(4) Working zones of 24" each and "OPTIONAL" working table length of 96"; CNC controlled head assembly with rapid (side-to-side) traverse.Head assembly with: (1) Horizontal boring & insertion unit with a 3 HP - 18,000 RPM Direct-Drive Spindle motor; "X" Axis is servo controlled for positioning; Digital Mechanical Readouts For Height and DepthHead is currently set up to bore/machine/insert 20 mm Lock-Dowel "Eclips", H-clips, Channel Locks & 8 mm Spring Pin Fasteners.Material thickness capacity 0.5" - 1" max. Material thickness with digital readout for height adjustment. -- Clamping System:(8) Pneumatic, quick side-to-side adjustable hold-down clamps for horizontal "Lock-Dowel" processing on the panel edge.(1) Pneumatic Clamping Bar for vertical boring into the panel face/back. -- Operator Interface:15" Color Touchscreen control + Windows 10 Operating System. Ethernet 1 x PCIE Broadcom GbE (or similar), USB: 2 x USB 2.0 (or similar), Serial Port: 1 x RS-232 (or similar)The on-screen graphics of the operator interface have been designed to allow for quick programming at the machine. Typically, programs can be written and recalled in less than one minute.The Interface is open architecture allowing it to integrate with design software that can give hole locations in the form of a .xml file or a bar code (with bar code reader purchase found in options).Standard Features in the software include: 1. Graphic interface to show where holes are to be drilled and if a dowel is to be inserted. 2. Pattern Drilling/Inserting.3. Password protection of certain features/functions. 4. Online diagnostic capability (if machine is connected to an internet connection). 5. Toggle between Metric or Imperial programing parameters. -- Features: This machine will insert H-clips, Channel Locks and Spring Pins with ease. Using CNC control, this machine positions the drilling spindle to bore holes and insert the Lockdowel hardware. -- Complete with:Anti slip table surface, rack & pinion drive, and centralized dust collection manifold. -- Actual model is: PILLAR MACHINE HPLD

The seller has confirmed that this Pinheiro planer is in good working/running condition. - Double sided planer with side saw - Complete package - Manual - no year...Motor HP 20 bottom, 10 top

(2) 2-1/2 HP motors 5/8” arbors 12” blade capacity max width 3 - 5/16” nax depth 2-5/8”

12” blades 1-1/2 HP motors - 3 phase foot pedal control

PMK C 1205 Single End Coping Machine -- With the C-1205 Coping Machine you can run your Styles first or run your cope first, this machine using a 7.5 HP motor has counter rotating spindles to insure Chip free coping of either square. -- Single profiled or double profiled parts. Since we are only coping one end at a time the length doesn't matter. We can also cope more than one part at a time up to 13.5" wide on the C-1205. -- Two counter-rotating spindles 1.25" in Diameter. -- Capacity of maximum (2) cutters on stack tooling -- Spindle Speed 7,000 RPM; cycle time approx. (4) Seconds. -- Side Pressure Clamp to insure proper alignment with a fence. -- Cutter Heads totally enclosed for Safety!

PMK C 1203 Single End Coping/Tenoning Machine -- With the C-1203 Coping Machine you can run stiles first or cope first, this machine using a 5 HP motor has counter rotating spindles to insure chip free coping of either square, single profiled or double profiled parts. -- Since we are only coping one end at a time the length doesn't matter. We can also cope more than one part at a time up to 9.5" wide on the C-1203. -- (2) Counter rotating spindles 1.25" diameter. -- Spindle Speed 7,000 RPM; cycle time approx. (4) seconds. -- Side Pressure Clamp to insure proper alignment with fence. -- Cutter Heads totally enclosed for Safety!

PMK MACHINERY C-1203 HSK -- With the C-1203 Coping Machine you can run your Styles first or run your cope first, this machine using a 5 HP motor has counter rotating spindles to insure Chip free coping of either square, single profiled or double profiled parts -- Since we are only coping one end at a time the length doesn't matter. -- We can also cope more than one part at a time up to 9.5" wide on the C-1203 -- Two counter rotating spindles 1-1/4" diameter, rotating at 7000 rpm -- 60 seconds or less tooling change -- Stacking tooling, 2 per spindle -- 7 1/2 HP 3 phase 230 /460 motor -- Unlimited part length -- Cycle time approx. 4 seconds. -- Side Pressure Clamp to insure proper alignment with fence. -- Cutter Heads totally enclosed for Safety! -- Included set of heads and insert tooling for popular door style and flooring

Pneumafil 13.5 460-10 304 Stainless Steel Reverse Air Bag House, 5,922 SQ/FT Cloth Media, 47,000 CFM @ 8:1 Air/Cloth Ratio, Very Good Condition, $82,000.00

Porter Planer Model 700 S/N 5916, Straight Knifes 10HP Motor

4X56 belt 1hp motor 3phase Controls work & motor runs

POWERMATIC TS29 TILING SPINDLE SLIDING TABLE SHAPER WITH 4 ROLL FEEDERSolid construction & design for any job from the largest to the smallest. -- Fully enclosed fabricated steel base to minimize sound level & vibration. -- Oversized 33-1/2" x 51" cast iron table with 11" x 51" sliding table that is supported by (6) tapered precision bearings. -- Sliding table with miter head, holddown & fence to accommodate numerous applications from end cuts to tenons. -- Fully adjustable rear fence with extruded aluminum face & accurate mechanical digital readouts on either side for fast & accurate setup to increase repeatability. -- 7.5 HP motor drives an extra large quill assembly with (3) oversized bearings to accept a variety of interchangeable spindles & router collets. -- Long 7" vertical spindle travel to allow the operator to stack tooling, 6-1/4" under the nut. -- Spindle capacity 3/4", to 1-1/4" -- (5) Spindle speeds in forward & reverse to provide the correct speed for any application (3000,4000,6000,8000,10000 rpm). -- Multiple table inserts for max. 9" opening for straight & tilting arbor operations which allow for virtually any size cutter. -- Arbor tilts 5°back and 45° forward for increased versatility with tooling. -- Large scale "ACCU Fence" with integrated dust collection shroud & cutterhead guard. -- AMBI-TECH Electronic brake. -- Clamping miter gauge. -- Push button magnetic control.

POWERMATIC 225 HELICAL HEAD PLANER24" x 8" Cap., 7.5 HP direct drive cutterhead motor, BYRD Spiral cutterhead.1.5 HP drive motor, variable feed speed from 20 - 100 FPM with forward/reversing switch. -- Features: sectional serrated infeed roller and sectional chipbreaker, (2) adjustable powered bed rollers; table size 24" x 48", with manual height adjustment. --Complete with: Magnetic motor controls & 8" dia. dust hood. Fully rebuilt recently and equipped with a BYRD Spiral cutterhead!

POWERMATIC 100 Single Sided PlanerSpecifications: -- 12" Cap. with 1/16" to 5" thickness opening -- 5 HP motor - 5,300 RPM -- 3-knife cutterhead with high speed steel knives -- 3-1/8" dia. head; 18 FPM fixed feed speed. -- Solid infeed rolls; 12" x 24" precision ground cast iron table. -- 1/4" max. depth of cut -- 7-1/2" min. stock length (unbutted). -- Complete with: Magnetic controls, cutterhead guard with dust chute on enclosed steel stand. -- Belt driven head

1 HP tenoner Approx. 2HPsaw Approx 28" x 16" table

Powermatic OES9138 Oscillating Edge Sander Includes: (5) Sander belts

POWERMATIC 221 PLANER WITH BYRD HELICAL HEAD20" x 8" Cap., 10 HP TEFC belted drive motor, BYRD Helical cutterhead, hand wheel micro-adjust table; 1 HP feed motor for variable speed from 20 - 50 FPM, segmented infeed roll and sectional chipbreaker, 4" dia. smooth outfeed roll. -- Complete with: Magnetic starter and dust hood.